Freescale Semiconductor MPC8260-TCOM User manual

3/1999
Rev 1.0
MPC8260 PowerQUICC II
MPC8260-TCOM User’s Manual
MOTOROLA
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MPC8260TCOM User’s Manual PRELIMINARY
2
0•1 INTRODUCTION
This page provides unpacking instructions, hardware preparation, and installation instructions for the
MPC8260TCOM.
0•2 UNPACKING INSTRUCTIONS
NOTE
If the shipping carton is damaged upon receipt,
request carrier’s agent be present during
unpacking and inspection of equipment.
Unpack equipment from shipping carton. Refer to packing list and verify that all items are present. Save
packing material for storing and reshipping of equipment.
CAUTION
AVOID TOUCHING AREAS OF INTEGRATED
CIRCUITRY; STATIC DISCHARGE CAN
DAMAGE CIRCUITS.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

PRELIMINARY MPC8260TCOM User’s Manual
GENERAL INFORMATION
3
CHAPTER 1 - GENERAL INFORMATION
1•1 INTRODUCTION
This manual provides general information, preparation for use and installation instructions, operating
instructions, functional description, and support information for the MPC8260TCOM board.
1•2 FEATURES
The main features of the MPC8260TCOM board are as follows:
• Two Fast Ethernet channels connected guilelessly to the Level One LXT970 device.
• The 2 Fast-Ethernet use FCC1 and FCC3.
• Each one of the Fast - Ethernet module can be disable/disable and controlled by SW.
• Two DS3 channels using the TRAN-SWITCH TXC-03401 FRAMER and TRAN-SWITCH TXC-
20153G DS3 Line Interface Module.
• Each one of the DS3 framer controlled via the MPC8260.
• The 2XDS3 use the TDMA1(DS3_1 FCC2) and TDMA2 (DS3_2 FCC3).
• Each one of the DS3 module can be disable/enable by HW.
• Eight T1 interfaces using MCC1 and MCC2.
• The 8 x T1 use the TOCTL PM4388 as a framer and 2 x PM4314 as a line interface module, both
controlled by the MPC8260.
• Each one of the eight T1 can be independently configured, monitor, isolated and controlled by
SW.
• The TOCTL (PM4388) is controlled by the MPC8260 via the address and data bus.
• The MPC8260TCOM board is powered and controlled by the MPC8260ADS via 2 x 128pin DIN
connectors.
1•3 SPECIFICATIONS
The MPC8260TCOM specifications are given in Table 1-1.
Table 1-1 MPC860SAR-PHY Specifications
CHARACTERISTICS SPECIFICATIONS
Power requirements (no other boards attached) +5Vdc @ 2 A (typical), 2.5 A (maximum)
Operating temperature 0 degrees to 30 degrees C ambient air temperature
Storage temperature -25 degrees to 85 degrees C
Relative humidity 5% to 90% (non-condensing)
Dimensions
Height
Depth
Thickness
9.17 inches (233 mm)
6.3 inches (160 mm)
0.063 inches (1.6 mm)
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MPC8260TCOM User’s Manual PRELIMINARY
GENERAL INFORMATION
4
1•4 GENERAL DESCRIPTION
The MPC8260TCOM Board includes the following modules: 8 x T1/E1, 2 x Fast Ethernet, 2 x DS3.
The MPC8260ADS includes the following modules: ATM155 and Fast Ethernet.
Both MPC8260TCOM and MPC8260ADS implements the following network for H/W & S/W development
applications:
ATM155M (FCC1 on MPC8260ADS) + 8 x T1 (MCC1 & MCC2),
ATM155M (FCC1 on MPC8260ADS) + 2 x Fast Ethernet (FCC2 on MPC8260ADS, FCC3),
ATM155M (FCC1 on MPC8260ADS) + 2 x DS3 (TDMa1 to FCC2, TDMa2 to FCC3),
3 x Fast Ethernet (FCC2 on MPC8260ADS, FCC1, FCC3).
NOTE: Some modules share the same GPIO. Care must be taken when configuring each one of the
modules, to prevent a conflict between them. Before operating the board the user should define the modes
of operation and configure the MPC8260 GPIO to the corresponding module.
Special care must be taken when using the Fast Ethernet interfaces. It do not have a h/w enable
signal, it is configured only through the MII MDC,MDIO signals.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

PRELIMINARY MPC8260TCOM User’s Manual
GENERAL INFORMATION
5
1•5 RELATED DOCUMENTATION
The following publications are applicable to the MPC8260TCOM and may provide additional helpful
information.
• MPC8260 Spec.
• MPC-SIERRA TOCTL PM4388. (http://www.pmc-sierra.com/register/toctl.asp#D)
• MPC-SIERRA QDSX PM4314. (http://www.pmc-sierra.com/register/qdsx.asp#D)
• Level-One LXT970 Fast - Ethernet Transceiver. (http://www.level1.com/product/qa/
lxt970qa.html)
• TRAN-SWITCH TXC-03401 DS3 FRAMER. (http://www.transwitch.com/pdh.html#ds3f)
• TRANS-SWITCH TXC20153G DS3 Line Interface Module. (http://www.transwitch.com/
pdh.html#limsn)
• TRANS-SWITCH TXC020020 DS3 Line Interface Device. (http://www.transwitch.com/pdh.html#)
1•6 ABBREVIATIONS USED IN THE DOCUMENT
• FCC - Fast serial Communication Controller.
• MCC - Multi Channel Controller.
• FE - Fast Ethernet.
• TOCTL - PMC-Sierra framer PM4388.
• LIU - Line interface module.
• QDSX - PMC-sierra LIU PM4314.
• DS3 - Serial communication of 44.736Mbps.
• DS3F - DS3 Framer.
• TCOM - MPC8260TCOM Board
• GPIO - General Purpose I/O related to the MPC8260 PORTS.
• ADS - MPC8260ADS
• Module - Each one of the options this board can give: 8 x T1, 2 x FE, 2 x DS3.
• CPM - Communication Processor Module.
• SPEC - Engineering Specification document.
1•7 REQUIRED EQUIPMENT
The MPC8260TCOM operates only with the MPC8260ADS.
The equipment required to connect the communication lines to the two cards is described bellow:
• The RJ45 connectors are separated to two groups:
• 8 x E1/T1 circuit connected by a 8 wires cable.
• 2 x Fast Ethernet circuit connected by a 8 wires cable.
• 4 x BNC 75Ωdedicated to 2 x DS3 circuit connected by a BNC cable. (2 - receive, 2 - transmit)
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MPC8260TCOM User’s Manual PRELIMINARY
GENERAL INFORMATION
6
FIGURE 1-1 MPC8260TCOM Connections.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

PRELIMINARY MPC8260TCOM User’s Manual
SOFTWARE AND HARDWARE PREPARATION
7
CHAPTER 2 - SOFTWARE AND HARDWARE PREPARATION
2•1 SOFTWARE PREPARATION
The TCOM is not a stand alone board. It should be connected to the MPC8260ADS. To select the desired
configuration and ensure proper operation of the MPC8260TCOM board, changes in the MPC8260 GPIO
configuration may be required. The following table describes the different configurations of all the modules
on the board. NOTE:
The FE modules have no H/W protection. Before using one of the FE module make sure that other modules
using the same GPIO are disabled. The following table shows the various types of communication
channels that can be implemented by connecting the TCOM & ADS cards.
The I/O are related to the MPC8260.
The dark column are the modules on the ADS.
Table 2: Ports Function Signals
Ports/name T1
1
A1
T1
2
B1
T1
3
C1
T1
4
D1
T1
5
A2
T1
6
B2
T1
7
C2
T1
8
D2
ADS
ATM8
FE
1
FCC1
ADS
FE 0
FCC2
FE
2
FCC3
TDM1
DS3
1
FCC2
TDM2
DS3
2
FCC3
PA2/DS3-TXCLK/TDMD2-TXCLK(clock20) I I
PA6/DS3-RXSYNC/TDMA1-L1RSYNC II
PA7/DS3-TXSYNC/TDMA1-L1TSYNC II
PA8/DS3-RXD0/TDMA1-L1RXD0 II
PA9/DS3-TXD0/TDMA1-L1TXD0 OO
PA14/MIIRXD3/ATM8-RXD4 II
PA15//MIIRXD2/ATM8-RXD5II
PA16/MIIRXD1/ATM8-RXD6 II
PA17/MIIRXD0/ATM8-RXD7II
PA18/MIITXD0/ATM8-TXD7 OO
PA19/MIITXD1/ATM8-TXD6OO
PA20/MIITXD2/ATM8-TXD5OO
PA21/MIITXD3/ATM8--TXD4 OO
PA26/MIIRXER/ATM8-RxClavII
PA27/MIIRXDV/ATM8-RxSOCII
PA28/MIITXEN/ATM8-RxEnb OO
PA29/MIITXER/ATM8-TxSOC OO
PA3/DS3-RXD1/TDMD2-RXCLK(clock19) I I
PA30/MIICRS/ATM8-TxClav II
PA31/MIICOL/ATM8-TxEnbOI
PB4/MIITXD3/DS3-RXSYNC/TDMA2-L1RSYNC I O I
PB5/MIITXD2/DS3-TXSYNC//TDMA2-L1TSYNC I O I
PB6/MIITXD1/DS3-RXD0/TDMA2-L1RXD0 IOI
PB7/MIITXD0/DS3-TXD0/TDMA2-L1TXD0 OOO
PB8/MIIRXD0/TDMD1-L1RSYNC II
PB9/MIIRXD1/DS3-TXD2/TDMD1-L1TSYNC IIO
PB10/MIIRXD2/TDMD1-L1RXD II
PB11/MIIRXD3/TDMD1-L1TXD OI
PB12/MIICRS/TDMC1-L1RSYNC II
PB13/MIICOL/DS3-TXD1/TDMC1-L1TSYNC IIO
PB14/MIITXEN/TDMC1-L1RXD IO
PB15/MIITXER/TDMC1-L1TXD OO
PB16/MIIRXER I
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MPC8260TCOM User’s Manual PRELIMINARY
SOFTWARE AND HARDWARE PREPARATION
8
PB17/MIIRXDV I
PB18/DS3-RXD2/MIIRXD3 II
PB19/DS3-RXD3/MIIRXD2 II
PB20/DS3-TXD1/TDMD2-L1RSYNC/MIIRXD1 IIO
PB21/DS3-TXD2/TDMD2-L1TSYNC/MIIRXD0 IIO
PB22/DS3-RXD1/TDMD2-L1RXD/MIITXD0 IOI
PB23/DS3-RXD2/TDMD2-L1TXD/MIITXD1 OOI
PB24/DS3-RXD3/TDMC2-L1RSYNC/MIITXD2 IOI
PB25/DS3-TXD3/TDMC2-L1TSYNC/MIITXD3 IOO
PB26/TDMC2-L1RXD/MIICRS II
PB27/TDMC2-L1TXD/MIICOL OI
PB28/TDMB2-L1TSYNC/MIIRXER II
PB29/TDMB2-L1RSYNC/MIITXEN IO
PB30/TDMB2-L1RXD/ATM8-MIIRXDV II
PB31/TDMB2-L1TXD/MIITXER OO
PC9/MIIMDIO XXX
PC10/MIIMDC XXX
PC11/DS3-TXD3 O
PC16/MIITXCLK(clock16)/TDMB2-TXCLK II
PC17/MIIRXCLK(clock15)/TDMB2-RXCLK II
PC18/TDMA2-TXCLK(clock14)/MIITXCLK II
PC19TDMA2-/RXCLK(clock13)/MIIRXCLK II
PC20/MIITXCLK(clock12)/ATM8-TxClk II
PC21/MIIRXCLK(clock11)/ATM8-RxClk II
PC22/TDMB1-TXCLK(clock10) I
PC23/TDMB1-RXCLK(clock9) I
PC24/TDMD1-TXCLK(clock8) I
PC25/TDMD1-RXCLK(clock7) I
PC26/DS3-TXCLK(clock6)/TDMC1-L1TXCLK(clock6) I I
PC27/DS3-RXCLK(clock5)/TDMC1-L1RXCLK(clock5) II
PC28/TDMC2-TXCLK(clock4) I
PC29/TDMC2-RXCLK(clock3) I
PC30//TDMA1-TXCLK(clock2) I
PC31/DS3-RXCLK(clock1)/TDMA1-RXCLK(clock1) I I
PD10/TDMB1-L1RSYNC I
PD11/TDMB1-L1TSYNC I
PD12/TDMB1-L1RXD I
PD13/TDMB1-L1TXD O
Table 2: Ports Function Signals
Ports/name T1
1
A1
T1
2
B1
T1
3
C1
T1
4
D1
T1
5
A2
T1
6
B2
T1
7
C2
T1
8
D2
ADS
ATM8
FE
1
FCC1
ADS
FE 0
FCC2
FE
2
FCC3
TDM1
DS3
1
FCC2
TDM2
DS3
2
FCC3
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

PRELIMINARY MPC8260TCOM User’s Manual
SOFTWARE AND HARDWARE PREPARATION
9
2•1•1 Module Selection.
2•1•1•1 Fast Ethernet selection
As mentioned above, the FE is enabled/disabled by S/W using PC9, PC10 as MII: MDIO and MDC pins.
The FE control is done via the MII internal registers.
FE_1 address = 00001h
FE_2 address = 00010h.
FE_0 address = 00000h (ADS).
2•1•1•2 8 x T1/E1
Each one of the 8 x T1/E1 is enabled by the following ports:
PD4 - T1_1
PD5 - T1_2
PD6 - T1_3
PD7 - T1_4
PD8 - T1_5
PD9 - T1_6
PD18 - T1_7
PD19 - T1_8
2•1•1•3 2 x DS3
Each one of the 2 x DS3 is enabled/disabled by the following ports:
PD25 - DS3 _1 (DS3_1 is enabled only if T1_1 & T1_7 & T1_8 is disabled and PD25 is low).
PA4 - DS3 _2 (DS3_2 is enabled only if T1_3 & T1_4 &T1_5 & T1_8 is disabled and PA4 is low).
2•2 INDICATORS
The MPC8260TCOM has the following indicators.
2•2•1 Fast Ethernet 1 TXD. LD1
LD1 is light whenever the MPC8260 transmits data to FE_1 (LXT970 - U1).
2•2•2 Fast Ethernet 1 RXD. LD2
LD2 is light whenever the MPC8260 receives data from FE_1 (LXT970 - U1).
2•2•3 Fast Ethernet 2 TXD. LD3
LD3 is light whenever the MPC8260 transmits data to FE_2 (LXT970 - U2).
2•2•4 Fast Ethernet 2 RXD. LD4
LD4 is light whenever the MPC8260 receives data from FE_2 (LXT970 - U2).
2•2•5 Fast Ethernet 1 SPEED. LD5
LD5 is light whenever FE_1 (LXT970 - U1) is configured to Fast Ethernet.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MPC8260TCOM User’s Manual PRELIMINARY
SOFTWARE AND HARDWARE PREPARATION
10
2•2•6 Fast Ethernet 1 LINK/LOCK. LD6
LD6 indicates in 100Mbps a scrambler lock and receipt of valid idle code.
LD6 indicates in 10Mbps a Link Valid status.
2•2•7 Fast Ethernet 1 Collision. LD7
LD7 indicates in default mode a collision.
LXT970 can be programmed for other indications. For detailed description see the LXT970 user’s manual.
2•2•8 Fast Ethernet 2 SPEED. LD8
LD8 is light whenever the FE_2 (LXT970 - U1) is configured to Fast Ethernet.
2•2•9 Fast Ethernet 2 LINK/LOCK. LD9
LD9 indicates in 100Mbps a scrambler lock and receipt of valid idle code. (LXT970 - U2)
LD9 indicates in 10Mbps a Link Valid status.
2•2•10 Fast Ethernet 2 Collision. LD10
LD10 indicates in default mode a collision.
LXT970 can be programmed for other indications.
2•2•11 DS3 2 FRAME ERROR. LD11
LD11 is light whenever an error on the F-bit or M-bit is occurred.
2•2•12 DS3 2 RXLOS. LD12
LD12 is light whenever 175 ±75 consecutive zeros appear in incoming data stream.
2•2•13 DS3 2 ENABLE. LD13
LD13 is light whenever DS3 2 is enabled.
2•2•14 DS3 1 FRAME ERROR. LD14
LD14 is light whenever an error on the F-bit or M-bit is occurred.
2•2•15 DS3 1 RXLOS LD15
LD15 is light whenever 175 ±75 consecutive zeros appear in incoming data stream.
2•2•16 DS3 1 ENABLE. LD16
LD16 is light whenever DS3 2 is enabled.
2•2•17 T1/E1 8 ENABLE. LD17
LD17 is light whenever T1/E1 _8 is enabled.
2•2•18 T1/E1 7 ENABLE. LD18
LD18 is light whenever T1/E1_7 is enabled.
2•2•19 T1/E1 6 ENABLE. LD19
LD19 is light whenever T1/E1_6 is enabled.
2•2•20 T1/E1 5 ENABLE. LD20
LD20 is light whenever T1/E1_5 is enabled.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...