Freescale Semiconductor TWR-MPC5125 User manual

TOWER SYSTEMQuick Start Guide for TWR-MPC5125
TWR-MPC5125
For high-resolution display applications

Freescale Tower System
The TWR-MPC5125 module is a single board computer as well as a part of the Freescale Tower System,
a modular development platform that enables rapid prototyping and tool re-use through reconfigurable
hardware. Take your design to the next level and begin constructing your Tower System today.
TOWER SYSTEM
Get to know the TWR-MPC5125
Primary Tower
Elevator Connector
Ethernet
RJ45
Mini-AB USB
Connector
HDMI
Connector
Microphone
Audio Out
Secondary Tower
Elevator Connector
Serial to
USB Bridge
Mini-B USB
Reset
(SW7)
Hibernate
(SW8)
SDHC
Connector
5V Power
Connector

Connect the HDMI cable
Using the HDMI-to-DVI-D cable
provided, connect the HDMI port on the
TWR-MPC5125 to a DVI-D port on a
display monitor. (Alternatively, connect the
HDMI port to an HDMI port on a monitor.
Cable not provided.)
Note: DVI –to–VGA is not supported.
Connect the USB cable
for the Serial-to-USB
bridge to provide power
Power the board from a host computer
by plugging in the dual-port USB cable.
Insert the two Standard-A plugs into two
USB ports a host computer. Then insert
the Mini-B side of the cable into the
Mini-B connector (J19) which is next to
the SDHC card slot.
(Alternatively, the board can be powered
by a 5V barrel jack from a wall supply. The
supply must be a center-hot configuration
2.1 mm jack and the voltage must be 5V.
Cable not provided).
TOWER SYSTEMQuick Start Guide for TWR-MPC5125
Step-by-Step Installation Instructions
STEP
2
In this Quick Start Guide, you will learn how to set up the TWR-MPC5125
module and run the default demonstration software. The following
instructions are for Windows®X P.
STEP
1

TOWER SYSTEM
View video on
the display
The board comes pre-programmed
to automatically boot the LimePC™
Linux operating system with video
demonstration application. Stop Here or
Continue on to LimeOS™
Linux desktop
Connect a USB mouse
and keyboard
Connect a USB mouse and USB keyboard
to a USB hub and connect the hub to the
Mini-AB connector (DOWN4) which is next
to the RJ45 port.
Press Q on the
keyboard or right-click
on the mouse
The video demonstration application will
close, revealing the LimeOS graphical
desktop. Explore with the USB mouse and
keyboard input.
Using the Serial-to-
USB bridge
The Freescale MC9S08JM60 Serial
to-USB bridge solution provides a RS-232
equivalent connection to the host computer
through the USB communications device
class. When plugged in and powered the
USB connection will enumerate as a COM
port on the PC.
To determine the COM port # for the
connection, right click on the My
Computer icon and select “Manage,” click
Device Manager, find and expand ports
(COM and LPT).
STEP
4
STEP
5
STEP
6
STEP
3

TOWER SYSTEMQuick Start Guide for TWR-MPC5125
Install software driver
When the cable is plugged
in the first time, the Found
New Hardware Wizard will start. Select
the option Install from a list or specific
location (Advanced), then select “Next.”
Browse for the file Freescale_CDC_Driver.
inf which is available on the DVD. Select
“Next,” then “Finish.”
Open Microsoft®
HyperTerminal or a
terminal program
of your choice
Select File > New Connection. Type a name
for the new connection. Pick the COM port
number for the connection found in step 4.
Choose the following port settings: Bits per
Second: 115200, Data bits: 8, Parity: None,
Stop bit: 1, Flow control: None.
STEP
8
STEP
7

TOWER SYSTEM
Press the reset button
on the board
Find the U-Boot prompt
on the terminal
Quickly press a key (on the host computer
keyboard) to stop automatic booting. The
U-Boot bootloader is pre-flashed in the
on-board NAND flash memory. At system
start up, U-Boot initializes the system and
allows the user to choose an operating
system to run.
Note: The default operating system that
automatically boots is LimeOS. To select
another operating system such as MQX,
press a key within three seconds to stop
automatic booting (autoboot).
Booting Freescale MQX
RTOS with digital sign
demo application
At the U-Boot prompt, type “run
mqxboot”. The MQX RTOS with demo
application loads into the SDRAM from
the NAND flash and executes.
View images on
the display
The Freescale MQX RTOS with digital
signage demonstration software is
preloaded on the board. This example
application shows how information,
advertising or other messages can be
displayed on screens in retail stores,
corporate buildings and other
public places.
STEP
10 STEP
12
STEP
11
STEP
9

TOWER SYSTEMQuick Start Guide for TWR-MPC5125
To make this the auto-boot option,
type “set bootcmd run mqxboot” and
press “Enter.” Then type “save” to save
this change to the U-Boot environment
variables in the nand flash.
To change back to autoboot Linux,
replace “mqxboot” with “nandboot.”
Booting LimeOS
Linux from the U-Boot
terminal
Press the Reset button and type “run
nandboot” at the U-Boot prompt
For more information, view the following
documents:
•MQXLab:Howtobuildandload
MQX applications
•LinuxLab:Howtorunpre-loaded
applications in the LimeOS Linux
demonstration software
•TWR-MPC5125User’sManual:
Hardware configuration, U-Boot and
Linux information
•MPC5125ReferenceManualandData
Sheet: MPC5125 information
For more information about other
mobileGT families, visit www.freescale.
com/mobilegt to get the latest lab
tutorials, application notes, other
supporting documents and learn about
other training opportunities.
For more information on Tower System
controllers and peripheral modules, visit
www.freescale.com/tower. To become
a member of the online Tower Geeks
community, visit www.towergeeks.org.
STEP
13

Freescale, the Freescale logo, mobileGT and MQX are trademarks
of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off.
All other product or service names are the property of their
respective owners. © 2010 Freescale Semiconductor, Inc.
Doc Number: MPC512CYMNQSG / REV 0
Agile Number: 926-78413 / REV A
Learn more at www.freescale.com/tower.
TOWER SYSTEM