Freewing F-105 Thunderchief User manual

EN 1~8
中9~16
User Manual

Introduction
Basic Product Information
Package List
PNP Install Insturctions
Install Main Wing
Install Horizontal Stabilizer
Install Vertical Stabilizer
Install Pushrod
Pushrod instructions
Battery Size
1
2
2
3
3
4
4
5
5
Center of Gravity
Control Direction Test
Dual Rates
Accessories Description
Motor Specifications
Motor Overview
Accessories Introduction
Servos Introductions
Install nose landing gear
lnstall rear landing gear
1
Item No.:FJ109
F-105 Thunderchief
Catalog
5
6
6
7
7
8
8
8

Contents
PNP ARF Plus Airframe
1
2
3
4
2
Item No.:FJ109
F-105 Thunderchief
Product Overview
800mm(31.5")
530mm(20.8")
2
Wing Loading：70g/dm
2
WingArea：7dm
Motor：2627-4500KV
Brushless Outrunner Motor
Ducted fan: 64mm 5-Blade Fan
ESC: 30A Brushless
Servo: 9g Plastic Servo (2pcs)
Top Speed : 120KPH/75MPH
Empty Weight:360g(without battery)
Bench Tested Thrust: 750g
Landing gear: fixed landing gear
(Optional spare part, need to purchase separately.)
Standard version
,
The package don t include the landing gear, if you need,please contact your local dealer.
No. Name
5
6
7
8
PNP ARF Plus Airframe
No. Name
Glue
Fin

3
Item No.:FJ109
F-105 Thunderchief
Step 1
Step 2
Carbon tube
(Ø4x200mm)
As shown in this photo:
1.Insert the carbon tube into the fuselage and keep
it in the center.
2.Apply the glue on the main wing install position of
fuselage (Indicated position as the photo shown),
then install the main wing on the fuselage and wait for it solidify.
Fuselage
Main wing
1.Use glue to attach the horizontal tail on the fuselage as the
below photo shown.
PNP lnstallation Instructions
Install Main Wing
Install Horizontal Stabilizer

4
Item No.:FJ109
F-105 Thunderchief
Use glue to install the vertical stabilizer on the rear fuselage. Ensure it is 90 degrees to
the horizontal plane of the fuselage. A crooked vertical stabilizer will hinder flight.
A
B
C
D
A-
B-
C-
D-
Elevator pushrod
Plastic tube
9g Servo
Elevator horn
A
B
C
Vertical stabilizer
PNP lnstallation Instructions
Install Vertical Stabilizer
1.Use a servo tester or radio to center
each servo.
2.Insert the threaded side of the rod to
the plastic tube and tighten the clevis.
3.One side pushrod insert to the servo
arm,adjust its length.And insert the
clevis to the elevator pushrod horn.
4.Repeat these 3 steps for the other side.
1Use a servo tester or radio to center .
each servo.
2.One side pushrod insert to the servo
arm,adjust its length.And insert the
clevis to the aileron pushrod horn.
3.Repeat these 2 steps for the other side.
Install Elevator pushrod
Install Aileron pushrod

5
Item No.:FJ109
F-105 Thunderchief
323mm
(12-6/8")
Pushrod diameter Ø1.0mm 1
2
3
2
3
1
Pushrod diameter Ø1.2mm
86mm
(3-3/8")
1
3
1
22
3
365mm
(14-3/8")
PNP lnstallation Instructions
Pushrod Instructions
Elevator pushrod size Elevator pushrod mounting hole
Aileron pushrod mounting hole
Aileron pushrod size
Battery cabin size:
L=150 W=42 H=42.5(mm)
Cockpit
Battery
Velcro
Battery tray
Use rubberized non-slip tape
or hook-and-loop tape
Pull the latch back
and open the cockpit.
Battery Size
We recommend the following LiPo battery:
3S 11.1V 1000mAh ~ 3S 11.1V 2200mAh
>
Discharge rate of C 30C
Before connecting the battery and receiver, please
switch on the transmitter power and make sure
the throttle stick is in the lowest position. Bind your
receiver to your transmitter according to your
transmitter’s instruction manual.
Center of Gravity
Correct Center of Gravity ( CG”) is critical for the aircraft to fly safely and in control. ”
Please refer to the following CG diagram to adjust your plane’s Center of Gravity.
- You can move the battery forward or backward to adjust the Center of
Gravity.
- If you cannot obtain the recommended CG
by moving the battery to a suitable location,
you can also install a counterweight to achieve
correct CG. However, with the recommended
battery size,no counterweight is required. We
recommend not flying with a battery size that
requires a counterweight.
”

H1
H2
H1
H2
H1/H2 7mm/7mm
D/R Rate：75%
H1/H2 9mm/9mm
D/R Rate：100%
H1/H2 13mm/13mm
D/R Rate：75%
H1/H2 15mm/15mm
D/R Rate：100%
升降舵
舵 面 测 试
6
Item No.:FJ109
F-105 Thunderchief
PNP lnstallation Instructions
Control Direction Test
Stick Down Stick Up
Aileron Elevator
Low Rate
High Rate
Dual Rates
According to our testing experience, use the following parameters to set Aileron/Elevator Rate.
Program your preferred Exponential % in your radio transmitter. We recommend using High Rate for the
first flight, and switching to Low Rate if you desire a lower sensitivity. On successive flights, adjust the
Rates and Expo to suit your preference.
Aileron(measured closest
to the fuselage)
Elevator(measured closest
to the fuselage)

A
B
C
D
E
F
G
As the left diagram, install ESC
and power system
A-
B-
C-
D-
E-
F-
G-
ESC fixed wood piece
ESC
64mm EDF power system
Fin
EDF cover
Screw (KA2.3x8)
Fuselage cover
2627-4500
Item No.:MO026272
7
Item No.:FJ109
F-105 Thunderchief
C
A
B
E
DF
G
Step 1Step 2
Step 3Step 4Step 5
2627-4500
11.1(3S) 28
64mm
5-blade EDF 750 49000 50E7201 310 2.4
Weight
(g)
Power system
No. Thrust(g)
Current(A)
Use voltage
(V)
Max power
(W)
Efficiency
(g/w)
EDF Fans
Motor
Specifications
（KV）
Rotating speed
(rpm)
Motor Specifications
A-
B-
C-
D-
E-
F-
G-
Motor 2627-4500KV
64mm Outrunner ducted frame
Screw (PM2.5x6 2pcs)
Motor collet
Motor collet backplate
64mm 5-blade ducted fan
Nut
Motor Overview
Standard version
Note: When the ESC and battery are connected,
avoid touching the ESC by hand to avoid accidental
injury due to heat When testing the EDF, please use
safety test stand for testing.Never hold an EDF unit in
your hand while it is powered on.
Accessories Description

1
2
8
Item No.:FJ109
F-105 Thunderchief
Accessories Introduction
Servos Introductions
Main wing(L)
Main wing(R)
1
2
Positive
Positive
300mm
300mm
9g plastic servo
9g plastic servo
Servo regulation Pos./Rev. Cable length
Position No.
If you need to purchase another brand’s servo, please
refer to the following list to choose a suitable servo.
Step 1
A
B
C
E
F
D
Step 2
G
H
J
D1
D2
D3
I
Step 3
K
Spare part name and parameters
A -
B -
C-
D-
E -
F -
G-
H-
I -
J -
K -
Servo fixed mount
9g Servo
Screw (PWA2.3x8 1pcs)
Set screw (M3x3 4pcs)
Nose wheel strut fixed piece
Nose wheel strut (top)
Wheel connecting part
Nose wheel strut (bottom)
Nose wheel (Ø35x10mm)
Wheel chock
Nose landing gear
Install nose landing gear
Please refer to the following photo for assembly and installation of the landing gear.
A-
B-
C-
D-
E-
F -
Set screw (M3x3)
Wheel chock
Nose wheel (Ø50x15mm)
Rear gear main strut
Main landing gear fixed mount
Main landing gear door
Step 1Step 2
A
B
C
D
E
F
Attention: install the wheel on
the direction of nose fuselage.
Please refer to the following photo for assembly and installation of the landing gear.
Install rear landing gear
Spare part name and parameters
Landing Gear Assemble
Landing gear is the optional part,please consult with the local distributor to purchase, and refer to the
following instructions to install.

Add.:FeiYi Building,face to Labor Bureau, Fumin Middle Road, Dalang Town,
Dongguan City，Guangdong Province, China
HK Freewing Model International Limited
东莞市 飞翼电子科技有限公司
香港飞翼模型国际有限公司
地址: 广东省东 莞市 大朗镇富民 中路402-408号 飞翼楼四楼
Web: http://www.sz-freewing.com
Email:[e-mail]
Tel: [phone] Fax:[phone]
Web: http://www.sz-freewing.com
Email:[e-mail]
Tel: [phone] Fax:[phone]
Dongguan Freewing Electronic Technology Ltd
R