Friedrich MR18DC3E User manual

Printed in Thailand/Imprimé en Thaïlande/Impreso en Thailandia
KEEP THIS OPERATION MANUAL
FOR FUTURE REFERENCE.
CONSERVEZ CE MODE D’EMPLOI AFIN DE
POUVOIR VOUS Y RÉFÉRER ULTÉRIEUREMENT.
GUARDE ESTE MANUAL DE FUNCIONAMIENTO
PARA PODERLO CONSULTAR EN EL FUTURO.
English
Français
Español
OPERATING MANUAL
MODE D’EMPLOI
MANUAL DE FUNCIONAMIENTO
P/N9367076017
COOLING MODEL
ROOM AIR CONDITIONER
MULTI SPLIT TYPE
(2 ROOMS)
Indoor Unit
MW09C3E
Outdoor Unit
MR18DC3E
Indoor Unit
MW12C3E
●Refer to the fold-out page on the cover.

Printed in Thailand/Imprimé en Thaïlande/Impreso en Thailandia
KEEP THIS OPERATION MANUAL
FOR FUTURE REFERENCE.
CONSERVEZ CE MODE D’EMPLOI AFIN DE
POUVOIR VOUS Y RÉFÉRER ULTÉRIEUREMENT.
GUARDE ESTE MANUAL DE FUNCIONAMIENTO
PARA PODERLO CONSULTAR EN EL FUTURO.
English
Français
Español
OPERATING MANUAL
MODE D’EMPLOI
MANUAL DE FUNCIONAMIENTO
P/N9367076017
COOLING MODEL
ROOM AIR CONDITIONER
MULTI SPLIT TYPE
(2 ROOMS)
Indoor Unit
MW09C3E
Outdoor Unit
MR18DC3E
Indoor Unit
MW12C3E
Outdoor Unit
MR24DC3E
●Refer to the fold-out page on the cover.

SPECIFICATIONS
MW09C3E ×2 MW12C3E ×2
MR18DC3E MR24DC3E
COOLING MODEL
230/208 V- 60 Hz
18,800/18,600 BTU/h 23,000/22,600 BTU/h
2,000/1,950 W 2,450/2,450 W
9.0/9.5 A 10.8/12.0 A
R22 1.83 ×2 Ibs. R22 2.31 ×2 Ibs.
●This specifications listed in the above table were measured under the following conditions.
●TEMPERATURE
COOLING
INDOOR 80 °F DB / 67 °F WB
OUTDOOR 95 °F DB / 75 °F WB
●Position of the AIRFLOW DIRECTION flap.
For ADJUSTING THE DIRECTION OF AIR CIRCULATION on Page En-11, use position 2.
●PIPING LENGTH 25 ft
MODELE
UNITÉINTÉRIEURE
UNITÉEXTÉRIEURE
TYPE
PUISSANCE
REFROIDISSEMENT
CAPACITE
ENTREE
INTENSITÉ
FRIGORIGENE
MW09C3E ×2 MW12C3E ×2
MR18DC3E MR24DC3E
MODÉLE REFROIDISSEMENT
230/208 V- 60 Hz
18.800/18.600 BTU/h 23.000/22.600 BTU/h
2.000/1.950 W 2.450/2.450 W
9,0/9,5 A 10,8/12,0 A
R22 1,83 ×2 Ibs. R22 2,31 ×2 Ibs.
●Ces spécifications figurant dans le tableau ci-dessus ont étémesurées sous les conditions suivantes.
●TEMPERATURE
REFROIDISSEMENT
INTERIEURE 80 °F DB / 67 °F WB
EXTERIEURE 95 °F DB / 75 °F WB
●Position du volet de direction de flux d’air. Pour le réglage de direction de circulation d’air àla page Fr-11, utiliser la position
2.
●LONGUEUR DE TUYAUTAG 25 ft
FICHE TECHNIQUE
MW09C3E ×2 MW12C3E ×2
MR18DC3E MR24DC3E
MODELO DE REFRIGERACIÓN
230/208 V- 60 Hz
18.800/18.600 BTU/h 23.000/22.600 BTU/h
2.000/1.950 W 2.450/2.450 W
9,0/9,5 A 10,8/12,0 A
R22 1,83 ×2 Ibs. R22 2,31 ×2 Ibs.
●Las especificaciones mencionadas en la tabla de arriba se basan en las mediciones bajo las condiciones siguientes.
●TEMPERATURA
REFRIGERACIÓN
INTERIOR 80 °F DB / 67 °F WB
EXTERIOR 95 °F DB / 75 °F WB
●Posición de la lama deflectora de la DIRRECCIÓN DEL FLUJO DE AIRE. Para el AJUSTE DE LA DIRECCIÓN DE CIRCULACIÓN
DEL AIRE de la página Sp-11, emplee la posición 2.
●LONGITUD DE LOS TUBOS 25 ft
ESPECIFICACIONES
Fig. 6
Fig. 1
Fig. 2
Fig. 5
Fig. 7
Fig. 3
Fig. 4
Fig. 8
En-1
CONTENTS
SAFETY PRECAUTIONS
WARNING!
CAUTION!
SAFETY PRECAUTIONS .................................... En-1
FEATURES AND FUNCTIONS ........................... En-4
NAME OF PARTS ................................................ En-5
PREPARATION .................................................... En-6
OPERATION ........................................................ En-7
TIMER OPERATION ............................................ En-9
SLEEP TIMER OPERATION .............................. En-10
ADJUSTING THE DIRECTION OF
AIR CIRCULATION ............................................ En-11
SWING OPERATION ......................................... En-12
MANUAL AUTO OPERATION .......................... En-12
CLEANING AND CARE ..................................... En-13
TROUBLESHOOTING ....................................... En-16
OPERATING TIPS.............................................. En-17
This mark indicates procedures which, if improperly performed, might lead to the
death or serious injury of the user.
This mark indicates procedures which, if improperly performed, might possibly result
in personal harm to the user, or damage to property.
Safety Symbols
The triangular symbol indicates DANGER, WARNING and CAUTION items.
This symbol indicates prohibited operations. The prohibited action is indicated both within the symbol,
and in nearby explanations.
●This symbol indicates instructions regarding operations which are to be performed by the user.
●Before using the appliance, read these “SAFETY PRECAUTIONS”thoroughly and operate in the correct way.
●The instructions in this section all relate to safety; be sure to maintain save operating conditions.
●“WARNING”and “CAUTION”have the following meanings in these instructions:
WARNING!
Do not attempt to install this air conditioner by yourself.
●Consult authorized service personnel for all installations.
Consult authorized service personnel for any repairs.
●Do not attempt to remove parts, or service the unit yourself, since you may be
exposed to dangerous electrical shock. This appliance contains no user-service-
able parts.
When moving, consult authorized service personnel for discon-
nection and installation of the unit.

SPECIFICATIONS
MW09C3E ×2 MW12C3E ×2
MR18DC3E MR24DC3E
COOLING MODEL
230/208 V- 60 Hz
18,800/18,600 BTU/h 23,000/22,600 BTU/h
2,000/1,950 W 2,450/2,450 W
9.0/9.5 A 10.8/12.0 A
R22 1.83 ×2 Ibs. R22 2.31 ×2 Ibs.
●This specifications listed in the above table were measured under the following conditions.
●TEMPERATURE
COOLING
INDOOR 80 °F DB / 67 °F WB
OUTDOOR 95 °F DB / 75 °F WB
●Position of the AIRFLOW DIRECTION flap.
For ADJUSTING THE DIRECTION OF AIR CIRCULATION on Page En-11, use position 2.
●PIPING LENGTH 25 ft
MODELE
UNITÉINTÉRIEURE
UNITÉEXTÉRIEURE
TYPE
PUISSANCE
REFROIDISSEMENT
CAPACITE
ENTREE
INTENSITÉ
FRIGORIGENE
MW09C3E ×2 MW12C3E ×2
MR18DC3E MR24DC3E
MODÉLE REFROIDISSEMENT
230/208 V- 60 Hz
18.800/18.600 BTU/h 23.000/22.600 BTU/h
2.000/1.950 W 2.450/2.450 W
9,0/9,5 A 10,8/12,0 A
R22 1,83 ×2 Ibs. R22 2,31 ×2 Ibs.
●Ces spécifications figurant dans le tableau ci-dessus ont étémesurées sous les conditions suivantes.
●TEMPERATURE
REFROIDISSEMENT
INTERIEURE 80 °F DB / 67 °F WB
EXTERIEURE 95 °F DB / 75 °F WB
●Position du volet de direction de flux d’air. Pour le réglage de direction de circulation d’air àla page Fr-11, utiliser la position
2.
●LONGUEUR DE TUYAUTAG 25 ft
FICHE TECHNIQUE
MW09C3E ×2 MW12C3E ×2
MR18DC3E MR24DC3E
MODELO DE REFRIGERACIÓN
230/208 V- 60 Hz
18.800/18.600 BTU/h 23.000/22.600 BTU/h
2.000/1.950 W 2.450/2.450 W
9,0/9,5 A 10,8/12,0 A
R22 1,83 ×2 Ibs. R22 2,31 ×2 Ibs.
●Las especificaciones mencionadas en la tabla de arriba se basan en las mediciones bajo las condiciones siguientes.
●TEMPERATURA
REFRIGERACIÓN
INTERIOR 80 °F DB / 67 °F WB
EXTERIOR 95 °F DB / 75 °F WB
●Posición de la lama deflectora de la DIRRECCIÓN DEL FLUJO DE AIRE. Para el AJUSTE DE LA DIRECCIÓN DE CIRCULACIÓN
DEL AIRE de la página Sp-11, emplee la posición 2.
●LONGITUD DE LOS TUBOS 25 ft
ESPECIFICACIONES
Fig. 6
Fig. 1
Fig. 2
Fig. 5
Fig. 7
Fig. 3
Fig. 4
Fig. 8
En-1
CONTENTS
SAFETY PRECAUTIONS
WARNING!
CAUTION!
SAFETY PRECAUTIONS .................................... En-1
FEATURES AND FUNCTIONS ........................... En-4
NAME OF PARTS ................................................ En-5
PREPARATION .................................................... En-6
OPERATION ........................................................ En-7
TIMER OPERATION ............................................ En-9
SLEEP TIMER OPERATION .............................. En-10
ADJUSTING THE DIRECTION OF
AIR CIRCULATION ............................................ En-11
SWING OPERATION ......................................... En-12
MANUAL AUTO OPERATION .......................... En-12
CLEANING AND CARE ..................................... En-13
TROUBLESHOOTING ....................................... En-16
OPERATING TIPS.............................................. En-17
This mark indicates procedures which, if improperly performed, might lead to the
death or serious injury of the user.
This mark indicates procedures which, if improperly performed, might possibly result
in personal harm to the user, or damage to property.
Safety Symbols
The triangular symbol indicates DANGER, WARNING and CAUTION items.
This symbol indicates prohibited operations. The prohibited action is indicated both within the symbol,
and in nearby explanations.
●This symbol indicates instructions regarding operations which are to be performed by the user.
●Before using the appliance, read these “SAFETY PRECAUTIONS”thoroughly and operate in the correct way.
●The instructions in this section all relate to safety; be sure to maintain save operating conditions.
●“WARNING”and “CAUTION”have the following meanings in these instructions:
WARNING!
Do not attempt to install this air conditioner by yourself.
●Consult authorized service personnel for all installations.
Consult authorized service personnel for any repairs.
●Do not attempt to remove parts, or service the unit yourself, since you may be
exposed to dangerous electrical shock. This appliance contains no user-service-
able parts.
When moving, consult authorized service personnel for discon-
nection and installation of the unit.

En-2
SAFETY PRECAUTIONS
WARNING!
Do not stay in direct cooling airflow for long periods.
●Excessive direct exposure to chilled air could be bad for your health.
●Be especially careful when going to bed, and in rooms where infants, aged, or sick
people are staying.
Do not insert fingers or objects into the outlet port or intake
grilles.
●A fan operates at high speed inside the unit, and personal injury could result.
●Be particularly careful regarding small children.
In the event of a malfunction (burning smell, etc.), immediately
stop operation, disconnect the power, and consult authorized
service personnel.
●Continuing to operate the unit under such conditions could lead to hazard of fire
or electrical shock.
CAUTION!
Be careful to provide adequate ventilation
particularly when using the unit in combi-
nation with other heating apparatus.
●Insufficient ventilation could lead to oxygen starvation.
Do not climb on, or place objects on, the
air conditioner.
●Personal injury could result from a falling object, or if
the unit tips over.
Do not hang on or cover the air conditioner.
Do not expose the air conditioner directly
to water.
●Electrical insulation could be damaged, resulting in elec-
trical shock.
Do not place animals or plants in the direct
path of the air flow.
Do not direct air flow at fireplaces or heat-
ing apparatuses.
●Direct air blowing on fires could result in improper com-
bustion or fire.
Do not set flower vases or water contain-
ers on top of air conditioners.
●Water leaking inside the unit could damage electrical
insulation, leading to danger of electrical shock.
Do not operate the air conditioner with wet
hands.
●Electrical shock could result.

En-3
SAFETY PRECAUTIONS
CAUTION!
Turn off power source when not using the
unit for extended periods.
Take precautions to prevent infants from
accidentally swallowing batteries.
Do not drink the water drained from the air
conditioner.
Take out the batteries from the remote con-
trol unit when not using for a long time.
●Take out the batteries to prevent troubles caused by
battery liquid leakage.
●If leaking battery fluid comes in contact with your skin,
eyes, or mouth, immediately wash with copious
amounts of water, and consult your physician.
Always operate with the air filter installed.
●Operating the unit without the air filter could cause ex-
cessive dirt to collect on internal parts, leading to mal-
function.
Install the indoor unit and remote control
unit at least one meter from any television
sets or radio.
●Signal radiation could be induced into the system to
give erroneous operation.
When installing the indoor unit and outdoor
unit, take precautions to prevent access by
infants.
●Unexpected accidents could occur.
Do not use inflammable gases near the air
conditioner.
Always turn off the electrical breaker when-
ever cleaning the air conditioner or chang-
ing the air filter.
●A fan operates at high speed inside the unit, and per-
sonal injury could result.
Check the condition of the installation for
damage.
●After lengthy use, arrange for visit by authorized serv-
ice personnel to check installation condition.
Do not use in applications involving the
storage of foods, plants or animals, preci-
sion equipment, or art works.
●The quality of the stored items may deteriorate.
Do not touch the heat exchanger radiator
fins.
●Personal injury could result.
●Be particularly careful when cleaning.
●Bending or damage to the fins will affect the efficiency
of the unit.
Do not block or cover the intake grille and
outlet port.
●Obstructing the ports will reduce operating efficiency,
leading to improper operation and possible damage.
Avoid installing the air conditioner near a
fireplace or other heating apparatus.
●Exposure to excessive heat could result in deformation
of the outer case.
Be sure to attach the intake grille securely.

En-4
FEATURES AND FUNCTIONS
AUTOMATIC OPERATION
Merely press the START/STOP button, and the unit will be-
gin automatic operation in either the Cooling or Dry mode
as appropriate, in accordance with the thermostat setting
and the actual temperature of the room.
SLEEP TIMER
When the SLEEP timer button is pressed during Cooling
mode, the thermostat setting is gradually raised during the
period of operation. When the set time is reached, the unit
automatically turns off.
WIRELESS REMOTE CONTROL UNIT
The WIRELESS REMOTE CONTROL UNIT allows convenient
control of air conditioner operation.
SWING OPERATION
The Air Flow Direction Louvers swings automatically up and
down so that the air speeds to every nook and corner of
your room.
REMOVABLE INTAKE GRILLE
The indoor unit’s INTAKE GRILLE can be removed for easy
cleaning and maintenance.
MILDEW-RESISTANT FILTER
The AIR FILTER has been treated to resist mildew growth,
thus allowing cleaner use and easier care.
SUPER QUIET OPERATION
When the FAN CONTROL button is used to select QUIET,
the unit begins super-quiet operation; the indoor unit’s air-
flow is reduced for quieter operation.

En-5
Fig. 1 Indoor Unit
1Operating Control Panel (Fig. 2)
2MANUAL AUTO button
3Remote Control Signal Receiver
4Indicator Lamps (Fig. 3)
5OPERATION Indicator Lamp (red)
6TIMER Indicator Lamp (green)
●If the TIMER indicator lamp flashes when
the timer is operating, it indicates that a
fault has occurred with the timer setting
(see page 17 Auto Restart).
7SWING Indicator Lamp (orange)
8Intake Grille (Fig. 4)
9Air Filter
0Air Flow Direction Louver
ARight-Left Louvers
(behind Air Flow Direction Louver)
BDrain Hose
CInter Unit-Line
DAir Cleaning Filter (optional)
Fig. 5 Outdoor Unit
EPower Supply
FIntake Port
GOutlet Port
HPipe Unit
IDrain port (bottom)
Fig. 6 Remote Control Unit
JSLEEP button
KMASTER CONTROL button
LSET TEMP./SET TIME button ( )
MSignal Transmitter
NTIMER button
OFAN CONTROL button
PSTART/STOP button
QAIR FLOW DIRECTION button
RSWING LOUVER button
Rear side (Fig. 7)
STIME ADJUST button
TACL button
(located inside battery compartment)
UTEST RUN button
●This button is used when installing the
unit, and should not be used under nor-
mal conditions, as it will cause the air con-
ditioner’s thermostat function to operate
incorrectly.
●If this button is pressed during normal op-
eration, the unit will switch to test opera-
tion mode, and the Indoor Unit’s OPERA-
TION Indicator Lamp and TIMER Indicator
Lamp will begin to flash simultaneously.
●To stop the test operation mode, press the
START/STOP button to stop the air condi-
tioner.
Remote Control Unit Display (Fig. 8)
WTransmit Indicator
XClock Display
YOperating Mode Display
ZTimer Mode Display
[Fan Speed Display
\Temperature Set Display
]Timer Set Indicator
`Temperature Set Indicator
NAME OF PARTS

En-6
PREPARATION
CAUTION!
●Take care to prevent infants from acciden-
tally swallowing batteries.
●When not using the remote control unit
for an extended period, remove the bat-
teries to avoid possible leakage and dam-
age to the unit.
●If leaking battery fluid comes in contact
with your skin, eyes, or mouth, immedi-
ately wash with copious amounts of wa-
ter, and consult your physician.
●Dead batteries should be removed quickly
and disposed of properly, either by plac-
ing in a public battery collection recepta-
cle, or by returning to appropriate author-
ity.
●Do not attempt to recharge dry batteries.
Never mix new and used batteries, or
batteries of different types.
Batteries should last about one year
under normal use. If the remote control
unit’s operating range becomes appre-
ciably reduced, replace the batteries and
press the ACL button (Fig. 7 T) with
the tip of a ballpoint pen or other small
object.
Turn on the Power
In the case of a direct line connection, turn on the circuit
breaker.
Load Batteries (AAA ×2)
1Press and slide the battery compartment lid on the re-
verse side to open it.
Slide in the direction of the arrow while pressing the mark.
2Insert batteries.
Be sure to align the battery polarities ( ) correctly.
3Close the battery compartment lid.
Set the Current time
1Press the TIME ADJUST button (Fig. 7 S).
Use the tip of a ball-point pen or other small object to press the button.
2Use the SET TEMP./SET TIME buttons (Fig. 6 L)
to adjust the clock to the current time.
button: Press to advance the time.
button: Press to reverse the time.
(Each time the buttons are pressed, the time will be advanced/reversed in
one-minute increments; hold the buttons depressed to change the time
quickly in ten-minute steps.)
3Press the TIME ADJUST button again.
This completes the time setting and starts the clock.
To Use the Remote Control Unit
●The remote control unit must be pointed at signal receiver (Fig. 1 3) to operate
correctly.
●Operating range: About 7 meters.
●When a signal is properly received by the air conditioner, a beep be heard.
●If no beep is heard, press the remote control unit button again.
Remote Control Unit Holder
3To remove the Remote
Control Unit .
1Mount the Holder. 2Set the Remote Control
Unit.
Screws
Insert
Press in
Slide up
Pull out

En-7
Example: When set to COOL
Example: When set to 80 °F
To Select Mode Operation
1Press the START/STOP button (Fig.6 P).
The indoor unit’s OPERATION indicator lamp (red) (Fig. 3 5) will light.
The air conditioner will start operation.
2Press the MASTER CONTROL button (Fig.6 K) to se-
lect the desired mode.
Each time the button is pressed, the mode will change in the following
order:
AUTO COOL DRY FAN
About three seconds later, the entire display will reappear.
To Set the Thermostat
Press the SET TEMP. buttons (Fig. 6 L).
button: Press to raise the thermostat setting.
button: Press to lower the thermostat setting.
●Thermostat setting range:
Cooling/Drying........................ 64 to 88 °F
Fan ........................................... 62 to 88 °F
About three seconds later, the entire display will reappear.
NOTE:
●During Fan mode, set the unit to “– –“for continuous fan operation regard-
less of room temperature.
The thermostat setting should be considered a standard value, and may differ
somewhat from the actual room temperature.
To Set the Fan Speed
Press the FAN CONTROL button (Fig. 6 O).
Each time the button is pressed, the fan speed changes in the following order:
AUTO HIGH MED LOW QUIET
About three seconds later, the entire display will reappear.
When set to AUTO:
Cooling : As the room temperature approaches that of the thermostat setting,
the fan speed becomes slower.
Fan : The fan will operate at the optimum speed in accordance with the
room temperature in the vicinity of the indoor unit.
When set to QUIET:
SUPER QUIET operation begins. The indoor unit’s airflow will be reduced for
quieter operation.
●SUPER QUIET operation cannot be used during Dry mode. (The same is true
when dry mode is selected during AUTO mode operation.)
●During SUPER QUIET operation, Cooling performance will be reduced some-
what.
sss
Example: When set to AUTO
In order to increase the drying effect
during quiet cooling operation, the fan of
the indoor unit may stop.
OPERATION
s
sss
ss

En-8
To Select Automatic Operation
Press the MASTER CONTROL button to select AUTO.
The operating mode “AUTO”will appear alone in the display. The transmit indi-
cator will flash to indicate the command has been sent, and about three sec-
onds later the entire display panel will reappear.
To Set the Thermostat
Press the TEMPERATURE set button.
About three seconds later, the entire display will reappear.
NOTE: The thermostat setting should be considered a standard value, and may
differ somewhat from the actual room temperature.
LOW HIGH LOW HIGH LOW HIGH LOW HIGH LOW HIGH
When set to
4 °F lower
When set to
2 °F lower
When set to
“normal”
When set to
2 °F higher
When set to
4 °F higher
About Mode Operation
AUTO:
●Depending on the room temperature at the time operation begins, the operating
mode will be switched automatically as shown in the accompanying table.
Also, depending on the operating mode, the room temperature setting will cause
the “standard”temperature to be set as shown.
Actual Room Operating Mode Thermostat Setting
Temperature (standard setting)
88 °F or above →Cooling →82 °F
82 to 88 °F→Cooling →80 °F
78 to 82 °F→Dry →76 °F
74 to 78 °F→Dry →72 °F
Below 74 °F→Dry →68 °F
The operating mode and standard thermostat settings are selected automatically
when operation begins.
●When automatic operation is initiated, the fan will run at very low speed for about
one minute while the unit detects and selects the proper operating mode.
●Once the operating mode has been set, the mode will not change even if the
room temperature changes.
●If the START/STOP button is pressed to recommence operation within two hours
after stopping automatic operation, the unit will begin operating from the same
mode as before.
Cooling:
●Use to cool your room.
Dry:
●Use for gently cooling while dehumidifying your room.
●You cannot heat the room during Dry mode.
●During Dry mode, the unit will operate at low speed; in order to adjust room
humidity, the indoor unit’s fan may stop from time to time. Also, the fan may
operate at very low speed when detecting room humidity.
●The fan speed cannot be changed manually when Dry mode has been selected.
Fan:
●Use to circulate warm air from ceiling area throughout room when using space
heaters.
To Stop Operation
Press the START/STOP button.
The OPERATION indicator lamp (red) (Fig. 3 5) will go out.
During Cooling/Dry mode:
Set the thermostat to a temperature setting
that is lower than the current room tempera-
ture. The Cooling and Dry modes will not
operate if the thermostat is set higher than
the actual room temperature (in Cooling
mode, the fan alone will operate).
During Fan mode:
●Fan operation begins when room tem-
perature in the vicinity of the air condi-
tioner rises above the set thermostat
temperature; when the temperature
drops, fan operation stops.
●If the air emitted feels too cool, raise
the thermostat setting.
Example: When set to “normal”

En-9
TIMER OPERATION
Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (see page 6).
To Use the ON timer or OFF timer
1Press the START/STOP button (Fig. 6 P)
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light.
2Press the TIMER button (Fig. 6 N) to select the OFF
timer or ON timer operation.
Each time the button is pressed the timer function changes in the follow-
ing order:
RESET OFF ON
PROGRAM(OFF ON, OFF ON)
The indoor unit’s TIMER Indicator Lamp (green) (Fig. 3 6) will light.
3Use the SET TEMP./SET TIME button (Fig. 6 L) to ad-
just the desired OFF time or ON time.
Set the time while the time display is flashing (the flashing will continue
for about five seconds).
button: Press to advance the time.
button: Press to reverse the time.
About five seconds later, the entire display will reappear.
To Use the Program timer
1Press the START/STOP button (Fig. 6 P)
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light.
2Set the desired times for OFF timer and ON timer.
See the section “To Use the ON Timer or OFF Timer”to set the desired
mode and times.
About three seconds later, the entire display will reappear.
The indoor unit’s TIMER Indicator Lamp (green) (Fig. 3 6) will light.
3Press the TIMER button (Fig. 6 N) to select the PRO-
GRAM timer operation (either OFF ON or OFF ON
will display).
The display will alternately show “OFF timer”and “ON timer”, then change
to show the time setting for the operation to occur first.
●The PROGRAM timer will begin operation. (If the ON timer has been
selected to operate first, the unit will stop operating at this point.)
About five seconds later, the entire display will reappear.
About the Program timer
●The PROGRAM timer allows you to integrate OFF timer and ON timer operations
in a single sequence. The sequence can involve one transition from OFF timer to
ON timer, or from ON timer to OFF timer, within a twenty-four hour period.
●The first timer function to operate will be the one set nearest to the current time.
The order of operation is indicated by the arrow in the Remote Control Unit’s
display (OFF ON, or OFF ON).
●One example of Program timer use might be to have the air conditioner auto-
matically stop (OFF timer) after you go to sleep, then start (ON timer) automati-
cally in the morning before you arise.
To Cancel the Timer
Use the TIMER button to select “TIMER RE-
SET.”
The air conditioner will return to normal op-
eration.
To Change the Timer Setting
Perform steps 2and 3.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting) af-
ter making the timer setting wait until the
entire display reappears, then press the ap-
propriate buttons to change the operating
condition desired.
To Cancel the Timer
Use the TIMER button to select “TIMER
RESET.”
The air conditioner will return to normal
operation.
To Change the Timer Setting
1. Follow the instructions given in the sec-
tion “To Use the ON Timer or OFF Timer”
to select the timer setting you wish to
change.
2. Press the TIMER button to select either
OFF ON or OFF ON.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting), af-
ter making the timer setting wait until the
entire display reappears, then press the ap-
propriate buttons to change the operating
condition desired.
t
s
t
s
t
s
s
s
s
t
s

En-10
SLEEP TIMER OPERATION
Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped.
To Use the SLEEP Timer
While the air conditioner is operating or stopped, press the
SLEEP button (Fig. 6 J).
The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) and the TIMER
Indicator Lamp (green) (Fig. 3 6) will light.
To Change the Timer Setting
Press the SLEEP button (Fig. 6 J) once again and set the
time using the SET TIME buttons (Fig. 6 L).
Set the time while the Timer Mode Display is flashing (the flashing will continue
for about five seconds).
button: Press to advance the time.
button: Press to reverse the time.
About five seconds later, the entire display will reappear.
To Cancel the Timer:
Use the TIMER button to select “TIMER RE-
SET”.
The air conditioner will return to normal op-
eration.
To Stop the Air Conditioner During Timer
Operation:
Press the START/STOP button.
About the SLEEP Timer
To prevent excessive warming or cooling during sleep, the SLEEP timer function automatically modifies the thermostat setting
in accordance with the time setting. When the set time has elapsed, the air conditioner completely stops.
Set time
1 hour
2 °F4 °F
During Cooling/Dry operation:
When the SLEEP timer is set, the thermostat setting is auto-
matically raised 2 °F every sixty minutes. When the thermo-
stat has been raised a total of 4 °F, the thermostat setting at
that time is maintained until the set time has elapsed, at
which time the air conditioner automatically turns off.
SLEEP timer setting

En-11
ADJUSTING THE DIRECTION OF AIR CIRCULATION
Vertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’s AIR FLOW DIRECTION button. Hori-
zontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers.
Whenever making horizontal airflow adjustments, start air conditioner operation and be sure that the vertical air direction
louvers are stopped.
Vertical Air Direction Adjustment
Press the AIR FLOW DIRECTION button (Fig. 6 Q).
Each time the button is pressed, the air direction range will change as follows:
Cooling/Dry
mode
Fan mode
123(6)NOTE
1234567
CAUTION!
Never place fingers or foreign objects inside
the outlet ports, since the internal fan oper-
ates at high speed and could cause personal
injury.
●Always use the remote control unit’s
AIR FLOW DIRECTION button to adjust
the vertical airflow louvers. Attempt-
ing to move them manually could re-
sult in improper operation; in this case,
stop operation and restart. The louvers
should begin to operate properly
again.
●When used in a room with infants, chil-
dren, elderly or sick persons, the air
direction and room temperature
should be considered carefully when
making settings.
●Always operate the Air Flow Direction
Louvers and the Power Diffuser with
the air flow direction buttons on the
remote control. Forcible movement by
hand can cause incorrect operation. In
such a case, stop the operation to let
the unit return to normal condition.
Right-Left Louvers
knob
●Use the air direction adjustments within the ranges shown above.
●The vertical airflow direction is set automatically as shown, in accordance with
the type of operation selected.
During Cooling/Dry modes : Horizontal flow 1
During Fan mode : Downward flow 6
●If you wish to select a different airflow direction, you may use the remote control
unit’s AIR FLOW DIRECTION button to choose a different setting.
●During AUTO mode operation, for the first minute after beginning operation,
airflow will be horizontal 1; the air direction cannot be adjusted during this pe-
riod.
NOTE
You can select the air direction 1, 2, 3, or 6(downward) by pressing the AIR
FLOW DIRECTION button.
Use the air direction 6when you want to cool yourself for a while after taking
a bath or shower, or after coming back home in summer months.
But, for prevention of condensation on the louver, the air direction 6is auto-
matically released after 30 minutes and turned to the air direction 3.
Right-Left Adjustment
Adjust the Right-Left louvers.
●Move the Right-Left louvers to adjust air flow in the direction you prefer.

En-12
SWING OPERATION
Begin air conditioner operation before performing this procedure.
About Swing Operation
●The SWING range is as follows:
●The SWING operation may stop temporarily when the air
conditioner’s fan is not operating or when operating at
very low speeds.
●The airflow direction can not be adjusted during SWING
operation even when the AIR FLOW DIRECTION button is
pressed.
MANUAL AUTO OPERATION
Use the MANUAL AUTO operation in the event the Remote Control Unit is lost or otherwise unavailable.
How To Use the Main Unit Controls
Press the MANUAL AUTO button (Fig. 2 2) on the main
unit control panel.
To stop operation, press the MANUAL AUTO button once again.
(Controls are located inside the Intake Grille.)
NOTE
The air swings between 4and 7by pressing the SWING
LOUVER button after selecting the air direction 6(down-
ward) by pressing the AIR FLOW DIRECTION button.
Use this operation when you want to cool yourself for a
while after taking a bath or shower, or after coming back
home in summer months.
But, for prevention of condensation on the louver, the
swing of the air direction 4↔7is automatically released
after 30 minutes and turned to the swing of the air direc-
tion 1↔3.
To select SWING Operation
Press the SWING LOUVER button (Fig. 6 R).
The SWING indicator lamp (orange) (Fig. 3 7) will light.
In this mode, the Air Flow Direction Louvers will swing automatically to direct
the airflow both up and down.
To Stop SWING Operation
Press the SWING LOUVER button (Fig. 6 R) once again.
The SWING indicator lamp (orange) (Fig. 3 7) will go out.
Airflow direction will return to the setting before swing was begun.
●When the air conditioner is operated
with the controls on the Main unit, it
will operate under the same mode as
the AUTO mode selected on the Re-
mote Control Unit (see page 8).
●The fan speed selected will be
“AUTO”and the thermostat setting
will be standard.
Cooling/Dry
mode
Fan mode
13, (47) NOTE
13, 47

En-13
Before cleaning the unit, be sure to stop the unit and disconnect the power.
1. Disconnect the power. 2. Turn off the electrical breaker.
●A fan operates at high speed inside the unit, and personal injury could result.
When cleaning the air conditioner, turn off the electrical
breaker.
Never use water that is hotter than 100 °F. The body may
warp or change color.
The unit can be damaged by gasoline, benzine, thinners,
insecticides and other chemical agents.
Do not use inflammable sprays such as lacquer or hair spray
near the air conditioner.
Cleaning the Indoor Unit
Clean the indoor unit by wiping with a cloth dipped in cool
or warm water, then wipe with another soft, clean, dry cloth.
When Not Using the Unit for Extended
Periods (One Month or More)
Operate the unit on fan mode for about one-half day on a
day with clear weather, to assure that the internal parts are
dry (see page 7).
CAUTION!
When not using the unit for extended periods, dis-
connect the power for safety.
CLEANING AND CARE
Cleansing rag
Thinner
Gasoline
Benzine
Lacquer
Hair spray
Inspections and Repairs
Depending on the conditions of use, the internal parts of an air conditioner will become dirty after about two or three
seasons of use, and performance may be affected. For this reason, regular professional maintenance is recommended.
Consult authorized service personnel.
More than
100 °F
WARNING !

En-14
Cleaning the Intake Grille
1. Open the Intake Grille.
1Place your fingers at both lower ends of the grille
panel, and lift forward; if the grille seems to catch
partway through its movement, continue lifting up-
ward to remove.
2Pull past the intermediate catch and open the Intake
Grille wide so that it becomes horizontal.
2. Unlock the Intake Grille.
Hold the Intake Grille with one hand and pull the Knobs
on the right and the left all the way to unlock the Intake
Grille.
3. Clean with water.
Remove dust with a vacuum cleaner: wipe the unit with
warm water, then dry with a clean, soft cloth.
4. Set the mounting shaft of the Intake Grille
into the bearings at the top of the panel.
1Pull the Knobs all the way.
2Hold the grille horizontal and set the left and right
mounting shafts into the bearings at the top of the
panel.
5. Lock the Intake Grille.
Hold the Intake Grille with one hand and push the Knobs
on the right and the left all the way in to lock the Intake
Grille mounting shafts.
6. Close the Intake Grille.
Push the lower edge of the Intake Grille at both ends and
at the center to close it.
CAUTION!
Do not operate with open Intake Grille, as this can
cause accidents.
Intake Grille
Knob
Raise the horizontal Intake Grille to remove it.
Intake Grille
Mounting shaft
Knob
Intake
Grille
Mounting
shaft
Bearing
Knob
Intake Grille
Mounting shaft
Intake Grille

En-15
Cleaning the Air Filter
1. Open the Intake Grille, and remove the Air
Filter.
Lift up the air filter’s handle, disconnect the two lower
tabs, and pull out.
2. Remove dust with a vacuum cleaner or by
washing.
After washing, allow to dry thoroughly in a shaded place.
3. Replace the Air Filter and close the Intake
Grille.
1Align the sides of the Air Filter with the panel, and
push in fully, making sure the two lower tabs are re-
turned properly to their holes in the panel.
2Close the intake grille.
(For purposes of example, the illustration shows the unit
without intake grille installed.)
●Dust can be cleaned from the Air Filter either with a
vacuum cleaner, or by washing the filter in a solution of
mild detergent and warm water. If you wash the filter, be
sure to allow it to dry thoroughly in a shady place before
reinstalling.
●If dirt is allowed to accumulate on the Air Filter, air flow
will be reduced, lowering operating efficiency and increas-
ing noise.
●During periods of normal use, the Air Filters should be
cleaned every two weeks.
Air filter handle
Hooks (two places)
Hooks (two places)
CLEANING AND CARE

En-16
TROUBLESHOOTING
In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the
Power and consult authorized service personnel.
Merely turning off the unit’s power switch will not completely disconnect the unit from the power
source. Always be sure to disconnect the Power Supply Plug and turn off your circuit breaker to
ensure that power is completely off.
Before requesting service, perform the following checks:
WARNING!
Symptom
Doesn’t operate immedi-
ately:
Noise is heard:
Smells:
Mist or steam are
emitted:
Airflow is weak or stops:
Problem
●If the unit is stopped and then immediately started again, the com-
pressor will not operate for about 3 minutes, in order to prevent
fuse blowouts.
●Whenever the Power is disconnected and then reconnected to a
power outlet, the protection circuit will operate for about 3 min-
utes, preventing unit operation during that period.
●During operation and immediately after stopping the unit, the
sound of water flowing in the air conditioner’s piping may be
heard. Also, noise may be particularly noticeable for about 2 to 3
minutes after starting operation (sound of coolant flowing).
●During operation, a slight squeaking sound may be heard. This is
the result of minute expansion and contraction of the front cover
due to temperature changes.
●Some smell may be emitted from the indoor unit. This smell is
the result of room smells (furniture, tobacco, etc.) which have
been taken into the air conditioner.
●During Cooling or Dry operation, a thin mist may be seen emitted
from the indoor unit. This results from the sudden Cooling of
room air by the air emitted from the air conditioner, resulting in
condensation and misting.
●The fan may operate at very low speed during Dry operation or
when the unit is monitoring the room’s temperature.
●During SUPER QUIET operation, the fan will operate at very low speed.
●In the monitor AUTO operation, the fan will operate at very low speed.
NORMAL
FUNCTION
See Page
—
—
—
—
7
7
7

En-17
TROUBLESHOOTING
Symptom
Doesn’t operate at all:
Poor Cooling perform-
ance:
The unit operates
differently from the
remote control unit’s
setting:
See Page
—
6
9 to 10
—
7
6
CHECK ONCE
MORE
Items to check
●Has there been a power failure?
●Has a fuse blown out, or a circuit breaker been tripped?
●Is the POWER switch set to the OFF position?
●Is the timer operating?
●Is the air filter dirty?
●Are the air conditioner’s intake grille or outlet port blocked?
●Did you adjust the room temperature settings (thermostat) cor-
rectly?
●Is there a window or door open?
●Is a window allowing bright sunlight to enter? (Close the curtains.)
●Are there heating apparatus and computers inside the room, or
are there too many people in the room?
●Is the unit set for SUPER QUIET operation?
●Are the Remote Control Unit’s batteries dead?
●Are the Remote Control Unit’s batteries loaded properly?
OPERATING TIPS
Operation and Performance
In Event of Power Interruption
AUTO Restart
●If a power failure occurs during TIMER operation, the timer
will be reset and the unit will begin (or stop) operation at
the new time setting. In the event that this kind of timer
fault occurs the TIMER Indicator Lamp (green) will flash
(see page. 5).
●Use of other electrical appliances (electric shaver, etc.) or
nearby use of a wireless radio transmitter may cause the
air conditioner to malfunction. In this event, temporarily
disconnect the Power, reconnect it, and then use the re-
mote control unit to resume operation.
●The air conditioner power has been interrupted by a power
failure. The air conditioner will then restart automatically in its
previous mode when the power is restored.
●Operated by setting before the power failure. Then, the Air
Flow Direction Louvers will automatically be restored to the
direction before the power failure.
If the problem persists after performing these checks, or if you notice burning smells, or the
TIMER indicator Lamp (Fig. 3 6) flashes, immediately stop operation, disconnect the Power and
consult authorized service personnel.
WARNING!