Fujitsu Inverter Halcyon 9374379392-04 User manual

PART NO.9374379392-04
Compact Cassette Type
9374379392-04_OM.indb 19374379392-04_OM.indb 1 9/6/2010 10:36:17 AM9/6/2010 10:36:17 AM

En-1
SAFETY PRECAUTIONS ....................................... 1
FEATURES AND FUNCTIONS ............................... 2
NAME OF PARTS .................................................. 3
PREPARATORY OPERATION ............................... 4
OPERATION ........................................................... 4
TIMER FUNCTIONS .............................................. 6
ON/OFF TIMER ...................................................... 6
WEEKLY TIMER ..................................................... 7
TEMPERATURE SET BACK TIMER ...................... 9
ADJUSTING THE DIRECTION OF AIR CIRCULATION ... 10
SWING OPERATION ........................................... 10
ECONOMY OPERATION ......................................11
MANUAL AUTO OPERATION................................11
CLEANING AND CARE .........................................11
TROUBLESHOOTING ......................................... 13
OPERATING TIPS ................................................ 14
SELF-DIAGNOSIS ............................................... 16
CONTENTS
SAFETY PRECAUTIONS
●Do not attempt to install this air conditioner by yourself.
●This unit contains no user-serviceable parts. Always consult authorized service per-
sonnel for repairs.
●When moving, consult authorized service personnel for disconnection and installa-
tion of the air conditioner.
●
Do not become excessively chilled by staying for many hours in the direct cooling airflow .
●Do not insert fingers or objects into the outlet port or intake grilles.
●
Do not start and stop air conditioner operation by turning off the electrical breaker .
●Take care not to damage the power supply cable.
●
If the power supply cable of this appliance is damaged, it should only be replaced by the
authorized service personal, since special purpose tools and specified cable are required.
●In the event of a malfunction (burning smell, etc.), immediately stop operation, turn
off the electrical breaker, and consult authorized service personnel.
●In the event of refrigerant leakage, be sure to keep away from fire or any flamma-
bles. (consult an authorized service personnel)
●Provide occasional ventilation during use.
●Do not direct airflow at fireplaces or heating apparatus.
●Do not climb on, or place objects on, the air conditioner.
●Do not hang objects from the indoor unit.
●Do not set flower vases or water containers on top of air conditioners.
●Do not expose the air conditioner directly to water.
●Do not operate the air conditioner with wet hands.
●Do not pull power supply cable.
●Turn off power source when not using the unit for extended periods.
●
Always turn off the electrical breaker whenever cleaning the air conditioner or changing the air filter.
●Connection valves become hot during Heating; handle with care.
●Check the condition of the installation stand for damage.
●Do not place animals or plants in the direct path of the airflow.
●When restarting after a long period of disuse in the winter, turn the power switch on
at least 12 hours before starting the unit.
●Do not drink the water drained from the air conditioner.
●Do not use in applications involving the storage of foods, plants or animals, preci-
sion equipment, or art works.
●Do not apply any heavy pressure to radiator fins.
●Operate only with air filters installed.
●Do not block or cover the intake grille and outlet port.
●Ensure that any electronic equipment is at least 40 in (1m) away from either the in-
door or outdoor units.
●Avoid installing the air conditioner near a fireplace or other heating apparatus.
●
When installing the indoor and outdoor units, take precautions to prevent access by infants .
●Do not use inflammable gases near the air conditioner.
●Install the drain hose so that it drains water properly.
●This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, un-
less they have been given supervision or instruction concerning use of the appli-
ance by a person responsible for their safety. Children should be supervised to en-
sure that they do not play with the appliance.
CAUTION!
● Before using the appliance, read these “SAFETY PRECAUTIONS” thoroughly and operate in the correct way.
● The instructions in this section all relate to safety; be sure to maintain safe operating conditions.
● “DANGER”, “WARNING” and “CAUTION” have the following meanings in these instructions:
DANGER! This mark indicates procedures which, if improperly performed, are most likely to
result in the death or serious injury to the user or service personnel.
WARNING! This mark indicates procedures which, if improperly performed, might lead to the
death or serious injury of the user or service personnel.
CAUTION! This mark indicates procedures which, if improperly performed, might possibly re-
sult in personal harm to the user or damage to property.
DANGER!
9374379392-04_OM.indb 19374379392-04_OM.indb 1 9/6/2010 10:36:25 AM9/6/2010 10:36:25 AM

En-2
FEATURES AND FUNCTIONS
INVERTER
At the start of operation, large amount of power is used to
bring the room quickly to the desired temperature. Afterwards,
the unit automatically switches to a low power setting for eco-
nomic and comfortable operation.
ECONOMY OPERATION
When ECONOMY operation mode is operated, the room tem-
perature will be little higher than the set-temp under cooling
mode and lower than set-temp under heating mode. Therefore,
the ECONOMY mode is able to save more energy than other
normal mode.
SWING OPERATION
The Airflow Direction Louvers swings automatically up and
down so that the air speeds to every nook and corner of your
room.
SUPER QUIET OPERATION
When the FAN button is used to select QUIET, the indoor
unit begins super-quiet operation; the indoor unit’s airflow is
reduced to produce quieter operation.
AUTO CHANGEOVER
The operation mode (cooling, dry, heating) is switched auto-
matically to maintain the set temperature, and the temperature
is kept constant at all times.
Convenient function
WEEKLY TIMER
Use this timer function to set operating times for each day of
the week. Use the DAY OFF setting to switch off timed opera-
tion for a selected day in the coming week. Because all days
can be set together, the weekly timer can be used to repeat
the timer settings for all of the days.
TEMPERATURE SET BACK TIMER
Use this timer function to change the set temperature in the
operation times set for each day of the week. This can be used
together with other timer settings.
REMOVABLE INTAKE GRILLE
The indoor unit’s intake grille can be removed for easy
cleaning and maintenance.
MILDEW-RESISTANT FILTER
The AIR FILTER has been treated to resist mildew growth,thus
allowing cleaner use and easier care.

Remote controller
WIRED REMOTE CONTROLLER
The wired remote controller allows convenient control of indoor
unit operation.
WIRELESS REMOTE CONTROLLER (OPTION)
The optional wireless remote controller can be used.
When you use remote controller, there are following
different points as compared with using wired remote
controller.
[ The additional function for wireless ones ]
• SLEEP
• TIMER
• MINIMUM HEAT
And you can use both wireless and wired remote
controller simultaneously. (But function is limited.)
[ The restricted functions for wired ones ]
• Weekly timer
• Temperature set back timer

Energy saving and
Comfortable function
Clean function
9374379392-04_OM.indb 29374379392-04_OM.indb 2 9/6/2010 10:36:25 AM9/6/2010 10:36:25 AM

En-3
I
H
G
J
K
E
1
C
5
D
A
0
3
4
B
8
6
2
F
9
7
NAME OF PARTS
Remote controller
1START/STOP Button
2SET TEMP. (Temperature) Button
3MODE Button
4FAN Button
5ECONOMY Button
6TIMER MODE (CLOCK ADJUST) Button
7DAY (DAY OFF) Button
8SET BACK Button
9SET TIME ( < > ) Button
0TIMER DELETE Button
ATIMER SET Button
B
Vertical Airflow Direction and Swing Button
CHorizontal Airflow Direction and Swing
Button (This function cannot be used)
D
MAINTENANCE (FILTER RESET) Button
#1
EOperation Lamp
FTimer and Clock Display
GOperation Mode Display
HFan Speed Display
IOperation Lock Display
JTemperature Display
KFunction Display
Defrost Display
Thermo Sensor Display
ECONOMY Display
Vertical Swing Display
Filter Display#1
#1:
Can be used if set correctly during installation.
Please consult authorized serviceman when
using this function.
WIRED TYPE
1Air Filter (In Air Intake Grille)
2Airflow Direction Flaps
3Air Intake Grille
4Remote Controller (Wired)
5Control Panel
6Remote Control Signal Receiver
7MANUAL AUTO Button
●
When the MANUAL AUTO button is
pressed in for more than 10 seconds, the
forced cooling operation will start.
●The forced cooling operation is used
at the time of installation.
Only for authorized service personnel's use .
●
When the forced cooling operation starts
by any chance, press the START/STOP
button to stop the operation
.
●Please press the button at FILTER
INDICATOR RESET.
8
OPERATION Indicator Lamp (Green)
9TIMER Indicator Lamp (Orange)
●
TIMER Indicator lamp lights when the
timer is set from wireless remote control.
0
ECONOMY Indicator Lamp (Green)
●
ECONOMY indicator lamp lights when
ECONOMY OPERATION and MINIMUM
HEAT OPERATION is operating.
9374379392-04_OM.indb 39374379392-04_OM.indb 3 9/6/2010 10:36:25 AM9/6/2010 10:36:25 AM

En-4
PREPARATORY OPERATION
2
Press the SET TIME ( < > ) buttons to set the current time.
Press repeatedly to adjust the current time in
1-minute increments. Press and hold to adjust the current
time in 10-minute increments
.
ex. Monday PM 11:00
SU MO TU WE TH FR SA
1
3
5
Set the current day and time
Press the TIMER MODE (CLOCK
ADJUST) button for 2 seconds
or more. The time display on the
remote controller will flash.
SU MO TU WE TH FR SA
Press the DAY button and select the current day.
A appears around the selected day.
Press again to end.
3
4
SU MO TU WE TH FR SA SU MO TU WE TH FR SA
Press the SET BACK button to switch between the
12- and 24-hour time displays.
SET BACK
OPERATION
Instructions relating to heating are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
To start/stop operation
Operation lamp
Air conditioner ON: Lit brightly
Air conditioner OFF: Not lit
Press the START/STOP button.
9374379392-04_OM.indb 49374379392-04_OM.indb 4 9/6/2010 10:36:26 AM9/6/2010 10:36:26 AM

En-5
To set the operation mode
● Operation mode setting
● Room temperature setting
● Fan speed setting
Lower Rise
AUTO COOL DRY HEATFAN
Press the MODE button to set the operation mode.
If DRY is selected, the fan speed will be set to AUTO.
Temperature setting range
AUTO................................................ 64 to 88 °F
COOL/DRY....................................... 64 to 88 °F
HEAT ................................................ 60 to 88 °F
Press the SET TEMP. buttons to set the room temperature.
AUTO MEDHIGH LOW QUIET
Press the FAN button to set the fan speed.
Press the ECONOMY button to start or stop ECONOMY OPERA-
TION.
For details on the function, refer to page 11.
ECONOMY OPERATION
Room temperature sensor selection
●
This function is locked at the factory. In order to detect the room temperature correctly, consult author-
ized service personnel when using this function.
Press the ECONOMY button for more than 2 seconds to se-
lect whether the room temperature is detected at the indoor
unit or the remote controller.
When the thermo sensor display appears, the room
temperature is detected at the remote controller.
NOTES
• If this function is locked, the location where the room temperature is detected cannot be changed and the mark
flashes when the ECONOMY button is pushed for 2 seconds or more.
Indoor unit
OPERATION
9374379392-04_OM.indb 59374379392-04_OM.indb 5 9/6/2010 10:36:26 AM9/6/2010 10:36:26 AM

En-6
TIMER FUNCTIONS
OFF timer (See page 6.)
Use this timer function to stop air conditioner operation. The timer operates and air conditioner operation stops after
the set time has passed. The timer can be set up to 24 hours in advance.
ON timer (See page 6.)
Use this timer function to start air conditioner operation. The timer operates and air condition operation starts after the
set time has passed. The timer can be set up to 24 hours in advance.
WEEKLY timer (See page 7.)
Use this timer function to set operating times for each day of the week.
Use the DAY OFF setting to switch off timed operation for a selected day in the coming week.
Because all days can be set together, the weekly timer can be used to repeat the timer settings for all of the days.
Temperature SET BACK timer (See page 9.)
Use this timer function to change the set temperature in the operation times set for each day of the week.
This can be used together with other timer settings.
ON/OFF TIMER
2
• Press the TIMER DELETE button to cancel the timer mode.
• The timer mode can also be canceled by changing the timer mode using the TIMER MODE button.
1
NON
STOP
OFF
TIMER
ON
TIMER
WEEKLY
TIMER
No display Press the SET TIME ( < > ) buttons to set the time.
After the time is set, the timer will start automatically.
The amount of time until the OFF timer operates that is dis-
played on the timer display decreases as time passes.
From 1 to 24 hours
SU MO TU WE TH FR SA
ex. OFF timer set for 6 hours
● To cancel
To set the ON/OFF timer
Press the TIMER MODE button to
select the ON timer or OFF timer.
Part lock function
Press the DAY (DAY OFF) button and TIMER SET but-
ton simultaneously for 2 seconds or more to activate the
part lock function and lock all of the buttons on the remote
controller except the START/STOP button, SET TEMP.
buttons, MODE button, and FAN button. Press the buttons
again for 2 seconds or more to deactivate the part lock
function.
When the part lock function is activated, the mark
appears. If any button is pressed during the part lock, the
PL display flashes.
OPERATION
9374379392-04_OM.indb 69374379392-04_OM.indb 6 9/6/2010 10:36:27 AM9/6/2010 10:36:27 AM

En-7
WEEKLY TIMER
Press the TIMER MODE button to select the weekly timer.
2
Press the TIMER SET button for
2 seconds or more.
1
3
SU MO TU WE TH FR SA
369 12 15 18 21
● Day of the week setting
Press the DAY button to select the day of the week, and then press the
TIMER SET button to confirm the setting.
For ALL, all of the days can be set together when a appears around
each day.
ALL SU MO TU WE TH FR SA
SU MO TU WE TH FR SA
369 12 15 18 21
4● Time setting
5● To delete the operating time
NOTES
• The operating time can be set in 30-minute increments only.
• The OFF time can be carried over to the next day.
•
The ON timer and the OFF timer functions cannot be set using the weekly timer. Both an ON and OFF time must be set .
Weekly timer setting
SU MO TU WE TH FR SA
369 12 15 18 21
When the operating time is set, the
mark appears.
ex. The timer is set for 7:00-18:00.
12
Press the SET TIME ( < > ) buttons to set the time, and then press the
TIMER SET button to confirm the setting and proceed to the next ON or OFF
time setting.
Up to 2 times ON and OFF times can be set per day.
Press the DAY button to complete the time setting and return to the day of
the week setting.
ON-1 OFF-1 ON-2 OFF-2
123
Repeat steps 3and 4.
To complete the weekly timer settings, press the TIMER
SET button for 2 seconds or more.
If the TIMER DELETE button is pressed
during steps 3or 4, the operating time for
the selected day will be deleted.
If all the days are selected, the operating
times for all of the days will be deleted.
9374379392-04_OM.indb 79374379392-04_OM.indb 7 9/6/2010 10:36:27 AM9/6/2010 10:36:27 AM

En-8
To set the DAY OFF (for a holiday)
NOTES
• The DAY OFF setting is only available for days for which weekly settings already exist.
• If the operating time carries over to the next day (during a next day setting), the effective DAY OFF range will be set as shown
below.
• The DAY OFF setting can only be set 1 time. The DAY OFF setting is cancelled automatically after the set day has passed.
SU MO TU WE TH FR SA
369 12 15 18 21
SU MO TU WE TH FR SA
369 12 15 18 21
● To cancel
Follow the same procedures as those
for setup.
ex. The DAY OFF is set for Monday.
The mark flashes under a day of the week.
● Normal
Setting dayPreceding day Next day
ON OFF ON OFF
DAY OFF
WEEKLY WEEKLY
● Next day setting
Setting dayPreceding day Next day
WEEKLY
WEEKLY
ON OFF ON OFF
DAY OFF
WEEKLY timer operation
The operating time for the current
day is displayed.
SU MO TU WE TH FR SA
369 12 15 18 21
369 12 15 18 21
ex. Operating time 7:00-18:00
● To start
When the weekly timer is selected,
the timer starts automatically.
● To cancel
• Press the TIMER DELETE button to
cancel the timer mode
.
• The timer mode can also be
canceled by changing the timer
mode using the TIMER MODE
button.
1
During the weekly timer, press
the TIMER SET button for 2
seconds or more to set the
day.
Select the day to set the DAY
OFF
.
2
Press the DAY (DAY OFF)
button for 2 seconds or more
to set the DAY OFF.
3
Press the TIMER SET button
for 2 seconds or more to com-
plete the DAY OFF setting
.
4
WEEKLY TIMER
9374379392-04_OM.indb 89374379392-04_OM.indb 8 9/6/2010 10:36:28 AM9/6/2010 10:36:28 AM

En-9
TEMPERATURE SET BACK TIMER
Temperature SET BACK timer setting
NOTES
• The SET BACK timer only changes the set temperature, it cannot be used to start or stop air conditioner operation.
• The SET BACK timer can be set to operate up to 2 times per day but only 1 temperature setting can be used.
• The SET BACK timer can be used together with the ON, OFF, and weekly timer functions.
•
The SET BACK operating time is displayed only in the SET BACK confirmation display. (Refer to step 1 for the SET BACK confir-
mation display.)
ON OFF
76°F 76°F
84°F
SET BACK temperature
Normal temperature
Temperature SET BACK timer operation
Press the SET BACK button to change to the SET BACK con-
firmation display.
The SET BACK operating time and the set temperature will be
displayed.
1
SET BACK
SU
MO
TU WE TH FR
SA
369 12 15 18 21
If there is no existing
SET BACK tempera-
ture setting, “- -” will
be displayed for the
temperature.
Press the SET BACK button. The SET BACK confirmation display appears for
5 seconds, and then the timer starts automatically.
● To start
SET BACK
ex. Display during SET BACK timer operation
(The operating time will not be displayed.)
SU MO TU WE TH FR SA
2
Press the TIMER SET button
for 2 seconds or more.
3● Day setting ● Operating time setting
Follow the same procedures to set the operating time as those for the weekly timer. The TIMER DELETE button is also
used as described in the procedures for the weekly timer.
SU
MO
TU
WE
TH FR
SA
369 12 15 18 21
ex. When setting all days together
13
24
4● Temperature setting Press the SET TEMP. buttons to set the
temperature. (The temperature setting
range is the same as the range for the op-
eration mode.)
SU MO TU WE TH FR SA
369 12 15 18 21
ex. Operating time 15:00–22:00
5
Repeat steps 3and 4.
Press the TIMER SET button for
2 seconds or more to complete
the temperature SET BACK timer
settings.
● To cancel
Press the SET BACK button, and then
press the TIMER DELETE button while
the SET BACK confirmation display is
displayed. Even if the SET BACK button
is pressed again, the SET BACK timer
will be cancelled
.
12
9374379392-04_OM.indb 99374379392-04_OM.indb 9 9/6/2010 10:36:29 AM9/6/2010 10:36:29 AM

En-10
ADJUSTING THE DIRECTION OF AIR CIRCULATION
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
Start air conditioner operation before performing this procedure.
* Press the START/STOP button to start the air conditioner, and then
proceed as follows.
Press the VERTICAL AIRFLOW DIRECTION and SWING button to adjust the
direction of the vertical airflow.
To set the operation mode
●
Vertical air direction adjustment
Airflow Direction Setting:
1, 2, 3, 4: During Cooling/Heating/
Dry mode
●
The vertical airflow direction is set automatically as shown, in accordance with the
type of operation selected
.
During Cooling/Dry mode : Horizontal flow 1
* During Heating mode : Downward flow 4
●During AUTO mode operation, for the first minute after beginning operation, air-
flow will be horizontal 1; the air direction cannot be adjusted during this period.
●Horizontal air direction adjustment.
The function cannot be used.
●
Attempting to move up/down air di-
rection flaps manually could result
in improper operation; in this case,
stop operation and restart. The
louvers should begin to operate prop-
erly again .
●
When used in a room with infants,
children, elderly or sick persons, the air
direction and room temperature should
be considered carefully when making
settings .
Each time the button is pressed, the air direction range will change as follows:
1234
The remote controller’s display does not change.
SWING OPERATION
Begin air conditioner operation before performing this procedure.
Press the VERTICAL AIRFLOW DIRECTION and SWING button for more
than 2 seconds. (Stop the setting by pressing for more than 2 seconds again.)
To select/stop swing operation
●The SWING operation may stop temporarily when the air
conditioner’s fan is not operating, or when operating at very
low speeds.
About Swing Operation
The type of operation
Cooling/Heating/Dry/Fan
Range of swing
1to 4
9374379392-04_OM.indb 109374379392-04_OM.indb 10 9/6/2010 10:36:30 AM9/6/2010 10:36:30 AM

En-11
ECONOMY OPERATION
Begin Air Conditioner operation before performing this procedure.
To Use the ECONOMY Operation
Press the ECONOMY button.
The ECONOMY Indicator Lamp (green) will light.
ECONOMY operation begins.
To Stop the ECONOMY Operation
Press the ECONOMY button again.
The ECONOMY Indicator Lamp (green) will go out.
Normal operation begins.
About ECONOMY Operation
At the maximum output, ECONOMY Operation is approximately 70% of normal air conditioner operation for cooling and
heating.
If the room is not cooled (or heated) well during ECONOMY operation, select normal operation.
During the monitor period in the AUTO mode, the air conditioner operation will not change to ECONOMY operation even if
ECONOMY operation is selected by pressing the ECONOMY operation button.
When ECONOMY operation mode is operated, the room temperature will be little higher than the set-temp under cooling
mode and lower than set-temp under heating mode. Therefore, the ECONOMY mode is able to save more energy than other
normal mode.
In case of multi-type air conditioner, the ECONOMY operation mode is only available for the set indoor unit.
CLEANING AND CARE
●Before cleaning the unit, be sure to stop the unit and disconnect the power supply.
●Turn off the electrical breaker.
●A fan operates at high speed inside the unit, and personal injury could result.
●Be careful not to drop the intake grille.
●When used for extended periods, the unit may accumulate dirt inside, reducing its performance. We recommend that the
unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service per-
sonnel.
●When cleaning the unit’s body, do not use water hotter than 104 °F, harsh abrasive cleansers, or volatile agents like ben-
zene or thinner.
●Do not expose the unit body to liquid insecticides or hairsprays.
●If the unit will not be operated for a period of 1 month or more, be sure to allow the inner parts of the unit to dry thoroughly,
in advance, by operating the unit in fan mode for half a day.
CAUTION!
Indicator Lamp
:Lighting :OFF
MANUAL AUTO OPERATION
Use the MANUAL AUTO operation in the event the Remote Controller is lost or otherwise unavailable.
●When the air conditioner is operated
with the controls on the MANUAL AUTO
button, it will operate under the same
mode as the AUTO mode selected on
the Remote Controller.
●The fan speed selected will be “AUTO”
and the thermostat setting will be stand-
ard.(76°F)
How To Use the Main Unit Controls
Press the MANUAL AUTO button more than
3 seconds and less than 10 seconds on the
main unit control panel.
To stop operation, press the MANUAL AUTO button once again.
(Controls are located inside the intake grille)
9374379392-04_OM.indb 119374379392-04_OM.indb 11 9/6/2010 10:36:30 AM9/6/2010 10:36:30 AM

En-12
CLEANING AND CARE
1. Push the intake grille’s hooks inward towards the
center of the unit to open the intake grille.
2. Pull out the filter from the intake grille.
3. Clean the air filter.
Remove the dust from the air filters by vacuuming or
washing them. After washing, allow the air filters to dry
thoroughly in an area protected from sunlight.
4. Re-attach the air filters to the intake grille.
1Replace the air filter into its holder.
2Make sure that the air filter makes contact with the filter
stopper when it is replaced into its holder.
5.
Close the intake grille and push the intake grille’s
hooks outward
.
●Dust can be cleaned from the air filter either with a vac-
uum cleaner, or by washing the filter in a solution of mild
detergent and warm water. If you wash the filter, be sure
to allow it to dry thoroughly in a shady place before rein-
stalling.
●If dirt is allowed to accumulate on the air filter, airflow will
be reduced, lowering operating efficiency and increasing
noise.
Cleaning the Air Filter
Grille Hook
Air Filter
Intake Grille
Air Filter
Filter Hook
Grille Hook
After turning the power on,
press the MAINTENANCE button for
2 seconds or more on the remote control, or
press the MANUAL AUTO button
for 2 seconds or less on the indoor unit.
Filter Indicator Reset (A special setting)
● Can be used if set correctly during installation.
Please consult authorized serviceman when using this function.

It lights on when it is time to clean the air
filters.
:Flashing :OFF
9374379392-04_OM.indb 129374379392-04_OM.indb 12 9/6/2010 10:36:31 AM9/6/2010 10:36:31 AM

En-13
TROUBLESHOOTING
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical
breaker, and consult authorized service personnel.
Merely turning off the unit’s power switch will not completely disconnect the unit from the power
source. Always be sure to turn off the electrical breaker to ensure that power is completely off.
Before requesting service, perform the following checks:
Symptom Problem
See
Page
NORMAL
FUNCTION
Doesn’t operate immedi-
ately:
●If the unit is stopped and then immediately started again, the com-
pressor will not operate for about 3 minutes, in order to prevent
fuse blowouts.
●Whenever the electrical breaker is turned off then on again, the
protection circuit will operate for about 3 minutes, preventing unit
operation during that period.
—
Noise is heard: ●During operation and immediately after stopping the unit, the
sound of water flowing in the air conditioner’s piping may be heard.
Also, noise may be particularly noticeable for about 2 to 3 minutes
after starting operation (sound of coolant flowing).
●During operation, a slight squeaking sound may be heard. This is
the result of minute expansion and contraction of the front panel
due to temperature changes.
—
*●
During Heating operation, a sizzling sound may be heard occasion-
ally. This sound is produced by the Automatic Defrosting operation
14
Smells: ●Some smell may be emitted from the indoor unit. This smell is the
result of room smells (furniture, tobacco, etc.) which have been
taken into the indoor unit.
—
Mist or steam are
emitted:
●During Cooling or Dry operation, a thin mist may be seen emit-
ted from the indoor unit. This results from the sudden Cooling of
room air by the air emitted from the indoor unit, resulting in con-
densation and misting.
—
*● During Heating operation, the outdoor unit’s fan may stop, and
steam may be seen rising from the unit. This is due to the Auto-
matic Defrosting operation.
14
Airflow is weak or stops: *● When Heating operation is started, fan speed is temporarily very
low, to allow internal parts to warm up.
*● During Heating operation, if the room temperature rises above
the thermostat setting, the outdoor unit will stop, and the indoor
unit will operate at very low fan speed. If you wish to warm the
room further, set the thermostat to a higher setting.
—
*● During Heating operation, the unit will temporarily stop opera-
tion (between 4 and 15 minutes) as the Automatic Defrosting
mode operates. During the Automatic Defrosting operation,
will be shown on the remote controller display.
14
●The fan may operate at very low speed during Dry operation or
when the unit is monitoring the room’s temperature. —
●During QUIET operation, the fan will operate at very low
speed. —
●In the monitor AUTO operation, the fan will operate at very low
speed. —
●In case of Multi-type unit, if multiple units are operated in differ-
ent operation modes as shown below, the units operated after-
ward will stop and the OPERATION indicator lamp (green) will
flash, will be shown on the remote controller display.
Heating mode and cooling mode (or dry mode)
Heating mode and fan mode
16
Water is produced from
the outdoor unit:
*● During Heating operation, water may be produced from the out-
door unit due to the Automatic Defrosting operation. 14
The ECONOMY Indicator flashes
●Clean the filter. Afterwards, turn the ECONOMY Indicator off. 12
thermo sensor display
on the remote controller
is flashing:
●The room temperature sensor may be malfunctioning. Please con-
sult authorized service personnel. —
WARNING!
9374379392-04_OM.indb 139374379392-04_OM.indb 13 9/6/2010 10:36:32 AM9/6/2010 10:36:32 AM

En-14
TROUBLESHOOTING
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
Symptom Items to check See Page
CHECK ONCE
MORE
Doesn’t operate at all: ●Has the circuit breaker been turned off?
●Has there been a power failure?
●Has a fuse blown out, or a circuit breaker been tripped?
—
●Is the timer operating? 6 to 8
Poor Cooling (or *Heating)
performance:
●Is the air filter dirty?
●Are the air conditioner’s intake grille or outlet port blocked?
●
Did you adjust the room temperature settings (thermostat) correctly ?
●Is there a window or door open?
●In the case of Cooling operation, is a window allowing bright sunlight
to enter? (Close the curtains.)
●
In the case of Cooling operation, are there heating apparatus and
computers inside the room, or are there too many people in the room
?
—
●Is the unit set for QUIET operation? —
If the problem persists after performing these checks, or if you notice burning smells, stop operation immediately, turn off electric
breaker, and consult with authorized service personnel.
OPERATING TIPS
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
*Heating Performance
●This air conditioner operates on the heat-pump principle, absorbing heat from outdoor air and transferring that heat indoors. As
a result, the operating performance is reduced as outdoor air temperature drops. If you feel that insufficient heating perform-
ance is being produced, we recommend you use this air conditioner in conjunction with another type of heating appliance.
●Heat-pump air conditioners heat your entire room by recirculating air throughout the room, with the result that some time may
be required after first starting the air conditioner until the room is heated.
*When Indoor and Outdoor Temperature are High
●When both indoor and outdoor temperatures are high during use of the heating mode, the outdoor unit’s fan may stop at times.
*Microcomputer-controlled Automatic Defrosting
●When using the Heating mode under conditions of low outdoor temperature and high humidity, frost may form on the outdoor
unit, resulting in reduced operating performance.
In order to prevent this kind of reduced performance, this unit is equipped with a Microcomputer-controlled Automatic Defrost-
ing function. During the defrost cycle, the indoor fan will shutdown and will be displayed on the remote controller. It will
take anywhere from 4 to 15 minutes before the air conditioner starts up again.
●After heating operation stops, if frost forms on the outdoor unit, the unit will start Automatic Defrosting operation.
At this time, the outdoor unit will automatically stop after operating for a few minutes.
Low Ambient Cooling
●When the outdoor temperature drops, the outdoor unit’s fans may switch to Low Speed, or 1 of the fans may stop intermittently.
Dual Remote Controllers (optional)
An additional remote controller can be added up to the maximum of 2 remote controllers. Either remote controller can control the
air conditioner. However, the timer functions cannot be used at the secondary unit.
Group Control
1 remote controller can control up to 16 air conditioners.
All of the air conditioners will be operated with the same settings.
Group control cannot be used when using it by the multi type.
9374379392-04_OM.indb 149374379392-04_OM.indb 14 9/6/2010 10:36:34 AM9/6/2010 10:36:34 AM

En-15
OPERATING TIPS
HEAT & COOL MODEL (Reverse Cycle)
Auto changeover function
●When AUTO CHANGEOVER is selected, the air condi-
tioner selects the appropriate operation mode (Cooling
or Heating) according to your room’s present tempera-
ture.
●When AUTO CHANGEOVER is first selected, the fan will
operate at a very low speed for about a few minutes while
the unit determines the current conditions of the room and
selects the proper operation mode.
If the difference between thermostat setting and actual
room temperature is more than +4 °F
→Cooling operation
If the difference between thermostat setting and actual
room temperature is within ±4 °F
→
Determined by outdoor temperature
If the difference between thermostat setting and actual
room temperature is more than –4 °F
→
Heating operation
About Mode Operation
During Heating mode:
Set the thermostat to a temperature set-
ting that is higher than the current room
temperature. The Heating mode will not
operate if the thermostat is set lower than
the actual room temperature.
During Cooling/Dry mode:
Set the thermostat to a temperature
setting that is lower than the current
room temperature. The Cooling and Dry
modes will not operate if the thermostat
is set higher than the actual room tem-
perature (in Cooling mode, the fan alone
will operate).
During Fan mode:
You can not use the unit to heat and cool
your room.
Heating: ●Use to warm your room.
●
When Heating mode is selected, the air conditioner will operate at very low
fan speed for about 3 to 5 minutes, after which it will switch to the selected
fan setting. This period of time is provided to allow the indoor unit to warm up
before beginning full operation
.
●When the room temperature is very low, frost may form on the outside
unit, and its performance may be reduced. In order to remove such frost,
the unit will automatically enter the defrost cycle from time to time. Dur-
ing Automatic Defrosting operation, and the heat operation will be inter-
rupted.
● After the start of heating operation, it takes sometime before the room gets
warmer
.
Cooling: ●Use to cool your room.
Dry: ●Use for gently cooling while dehumidifying your room.
●You cannot heat the room during Dry mode.
●
During Dry mode, the unit will operate at low speed; in order to adjust room
humidity, the indoor unit’s fan may stop from time to time. Also, the fan may
operate at very low speed when adjusting room humidity
.
●The fan speed cannot be changed manually when Dry mode has been se-
lected.
Fan: ●Use to circulate the air throughout your room.
●When the room temperature is 4 °F higher than the set
temperature, the mode will switch between Cooling and
Drying.
●During the Drying mode operation, the FAN setting should
be switched to LOW for a gently cooling effect during which
the fan may temporarily stop rotating.
●
When the room temperature is near the thermostat setting,
the air conditioner will begin monitor operation. In the monitor
operation mode, the fan will operate at a very low speed. If
the room temperature subsequently changes, the air condi-
tioner will once again select the appropriate operation (Heating
or Cooling) to adjust the temperature to the value set in the
thermostat.
COOLING MODEL
Mode operation: AUTO
●Should the power supply to the air conditioner be inter-
rupted by a power failure, the air conditioner will restart
automatically in the previously selected mode once the
power is restored.
●Use of other electrical appliances (electric shaver, etc.) or
nearby use of a wireless radio transmitter may cause the
air conditioner to malfunction. In this event, temporarily
disconnect the power supply, reconnect it, and then use
the remote controller to resume operation.
AUTO Restart
In Event of Power Interruption
9374379392-04_OM.indb 159374379392-04_OM.indb 15 9/6/2010 10:36:35 AM9/6/2010 10:36:35 AM

En-16
OPERATING TIPS
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
*●During use of the heating mode, the top of the indoor unit
may become warm, but this is due to the fact that cool-
ant is circulated through the indoor unit even when it is
stopped; it is not a malfunction.
*●During use of the heating mode, the outdoor unit will
occasionally commence the defrost operation for brief
periods. During the defrosting operation, if the user sets
the indoor unit for heating again, the defrosting mode will
continue, and the heating operation will begin after com-
pletion of defrosting, with the result that some time may
be required before warm air is emitted.
Notice
This indoor unit can be connected to a multi-type outdoor unit. The multi-type air conditioner allows multiple indoor units
to be operated in multiple locations. The indoor units may be operated simultaneously, in accordance with their respective
output.
Instructions relating to inverter (❖) are applicable only to “INVERTER MODEL”.
❖ ●Operation can be done in the following different operating
modes.
Cooling mode and dry mode
Cooling mode and fan mode
Dry mode and fan mode
❖ ●The operating mode (heating mode or cooling (dry) mode)
of the outdoor unit will be determined by the operating
mode of the indoor unit that was operated first. If the in-
door unit was started in fan mode, the operating mode of
the outdoor unit will not be determined.
For example, if indoor unit (A) was started in fan mode
and then indoor unit (B) was then operated in heating
mode, indoor unit (A) would temporarily start operation
in fan mode but when indoor unit (B) started operating in
heating mode, will be shown on the unit (A) remote
controller display and it would go into standby mode. In-
door unit (B) would continue to operate in heating mode.
●
When using a multi-type air conditioner, the multiple
indoor units can be operated simultaneously, but when
2 or more indoor units of the same group are operated
simultaneously, the heating and cooling efficiency will
be less than when a single indoor unit is used alone.
Accordingly, when you wish to use more than 1 indoor
unit for cooling at the same time, the use should be con-
centrated at night and other times when less output is
required. In the same way, when multiple units are used
simultaneously for heating, it is recommended that they
be used in conjunction with other auxiliary space heat-
ers, as required.
●
Seasonal and outdoor temperature conditions, the struc-
ture of the rooms and the number of persons present
may also result in differences of operating efficiency.
We recommend that you try various operating patterns in
order to confirm the level of heating and cooling output
provided by your units, and use the units in the way that
best matches your family's lifestyle.
●
If you discover that 1 or more units delivers a low level
of cooling or heating during simultaneous operation, we
recommend that you stop simultaneous operation of the
multiple units.
❖ ●Operation cannot be done in the following different oper-
ating modes.
If the indoor unit is instructed to do an operating mode
that it cannot perform, will be shown on the remote
controller display and the unit will go into the standby
mode.
Heating mode and cooling mode (or dry mode)
Heating mode and fan mode
Multi-typer Air conditioner
Simultaneous Use of Multiple Units
SELF-DIAGNOSIS
When “Er” in Temperature Display is displayed, inspection of the air conditioning system is necessary. Please consult
authorized service personnel.
Unit number (usually 00)
Error code
ex. Self-diagnosis check
9374379392-04_OM.indb 169374379392-04_OM.indb 16 9/6/2010 10:36:35 AM9/6/2010 10:36:35 AM

Fr-1
SOMMAIRE
PRÉCAUTIONS DE SÉCURITÉ
ATTENTION!
●
Avant d’utiliser cet appareil, veuillez lire attentivement ces “PRÉCAUTIONS DE SÉCURITÉ” et veillez à respecter les conditions d’utilisation .
●
Les instructions contenues dans la présente section sont toutes liées à la sécurité car vous devez maintenir des conditions de fonctionnement sûres .
● Les symboles “DANGER”, “AVERTISSEMENT” et “ATTENTION” ont le sens suivant dans ce manuel:
DANGER!
Ce signe indique des démarches qui, si elles sont exécutées de façon incorrecte, peuvent
entraîner des blessures graves, voire la mort de l’utilisateur ou du personnel technique
.
AVERTISSEMENT!
Ce marquage indique des procédures qui, si elles ne sont pas effectuées correctement, peuvent
entraîner la mort ou de sérieuses blessures corporelles pour l’utilisateur ou le personnel d’entretien .
ATTENTION Ce symbole signale une démarche qui, si elle est exécutée de façon incorrecte, peut
entraîner un dégât pour l’utilisateur ou ses biens.
●N’essayez pas d’installer vous-même ce climatiseur.
●Cet appareil ne renferme aucune pièce réparable par l’utilisateur. Confiez votre ap-
pareil à un centre de réparation agréé pour toute réparation.
●En cas de déménagement, faites appel à votre centre de réparation agréé pour le
débranchement et l’installation du climatiseur.
●
Veillez à ne pas prendre froid en restant longtemps exposé directement au flux d’air froid.
●
N’introduisez pas vos doigts ou des objets dans l’orifice de sortie ou la grille d’admission d’air.
●
Ne démarrez pas et n’arrêtez pas le climatiseur en coupant le disjoncteur.
●
Faites attention de ne pas endommager le cordon d’alimentation.
●
Si le cordon d’alimentation de cet appareil est endommagé, il doit uniquement être remplacé par le
centre de réparation agréé, car des outils spéciaux et un cordon spécifique sont nécessaires .
●En cas de défaillance (odeur de brûlé, etc), arrêtez immédiatement l’appareil, désac-
tivez le disjoncteur, et consultez le personnel de réparation qualifié.
●En cas de fuite du produit réfrigérant, assurez-vous de le garder hors d’atteinte des
flammes ou de produits inflammables. (consultez le centre réparation agréé)
●Assurez une ventilation régulière pendant le fonctionnement de l’appareil.
●Ne dirigez pas le flux d’air vers un feu ouvert ou vers un appareil de chauffage.
●Ne grimpez pas sur le climatiseur et ne déposez pas d’objets sur celui-ci.
●Ne suspendez pas d’objets à l’appareil intérieur.
●
Ne déposez pas de vase de fleurs ou de récipient contenant de l’eau sur un climatiseur .
●N’exposez pas directement le climatiseur à de l’eau.
●N’utilisez pas le climatiseur avec des mains humides.
●Ne tirez pas sur le cordon d’alimentation.
●
Coupez l’alimentation si vous n’utilisez pas le climatiseur pour une période prolongée .
●
Coupez toujours le disjoncteur lors du nettoyage du climatiseur ou du remplacement d’un filtre .
●Les vannes de raccordement sont soumises à la chaleur pendant l’opération de
chauffage; toujours les manipuler avec la plus grande précaution.
●Vérifiez si le support d’installation est en bon état.
●
Ne placez pas des animaux ou des plantes directement dans le courant d’air de l’appareil .
●En hiver, lors d’un redémarrage après une longue période d’inutilisation, mettez l’ap-
pareil sous tension au moins 12 heures avant sa mise en marche.
●Ne buvez pas l’eau de vidange du climatiseur.
●
Éloignez aliments entreposés, plantes, animaux, instruments de précision et objets d’art d’un climatiseur .
●N’appliquez aucune forte pression sur les ailettes du radiateur.
●Ne faites jamais fonctionner l’appareil sans ses filtres à air.
●N’obstruez pas et ne couvrez pas la grille d’admission ni l’orifice de sortie.
●
Veillez à tenir tout équipement électronique à 40 in. (1m) au moins des appareils intérieur et extérieur.
●
Évitez d’installer le climatiseur près d’un feu ouvert ou d’autres équipements de chauffage .
●Lorsque vous installez les unités d’intérieur et d’extérieur, veillez à ce qu’elles soient
hors de portée des enfants.
●N’utilisez pas de gaz inflammables à proximité du climatiseur.
●Installez le tuyau d’évacuation afin que l’eau s’évacue correctement.
●
L’utilisation de cet appareil n’est pas prévue pour des personnes (y compris les enfants) ayant
des capacités physiques, sensorielles ou mentales réduites, ou un manque d’expérience et de
connaissance, à moins qu’ils ne soient supervisés ou instruits par une personne responsable de
leur sécurité. Les enfants doivent être surveillés pour garantir qu’ils ne jouent pas avec l’appareil .
DANGER!
PRÉCAUTIONS DE SÉCURITÉ ............................. 1
FONCTIONNALITÉS ET FONCTIONS................... 2
NOMENCLATURE DES ORGANES ....................... 3
PREPARATIFS........................................................ 4
FONCTIONNEMENT............................................... 4
FONCTIONS DE LA MINUTERIE ........................... 6
MINUTERIE DE MISE EN MARCHE/ARRET ......... 6
MINUTERIE HEBDOMADAIRE .............................. 7
MINUTERIE D’ABAISSEMENT DE LA TEMPERATURE ..... 9
RÉGLAGE DE LA DIRECTION DU FLUX D’AIR ..... 10
FONCTIONNEMENT OSCILLANT........................ 10
FONCTIONNEMENT ÉCONOMIQUE....................11
FONCTIONNEMENT MANUAL AUTO...................11
NETTOYAGE ET ENTRETIEN...............................11
GUIDE DE DÉPANNAGE...................................... 13
CONSEILS D’UTILISATION.................................. 14
AUTO-DIAGNOSTIC............................................. 16
9374379392-04_OM.indb 19374379392-04_OM.indb 1 9/6/2010 10:36:35 AM9/6/2010 10:36:35 AM

Fr-2
FONCTIONNALITÉS ET FONCTIONS
INVERSEUR
Lors du démarrage de l’opération, une grande quantité
d’électricité est utilisée pour amener rapidement la pièce à la
température souhaitée. Par la suite, l'appareil commute au-
tomatiquement sur un réglage basse consommation pour un
fonctionnement économique et confortable.
FONCTIONNEMENT ÉCONOMIQUE
Quand le mode économique est utilisé, la température de la
pièce sera légèrement supérieure à la température définie
en mode refroidissement et légèrement inférieure en mode
chauffage. Par conséquent, le mode économique permet
d'économiser plus d'énergie que le mode normal.
FONCTIONNEMENT OSCILLANT
Les lames de direction du flux d’air oscillent automatiquement
de haut en bas afin que l’air circule dans les moindres recoins
de votre pièce.
FONCTIONNEMENT SUPER SILENCIEUX
Quand la touche FAN est utilisée pour sélectionner QUIET
(silencieux), l’appareil commence le fonctionnement super
silencieuxl; le flux d’air de l’unité intérieure est réduit pour as-
surer un fonctionnement plus silencieux.
FCHANGEMENT AUTOMATIQUE
Le mode de fonctionnement (Refroidissement, Déshumidifica-
tion, Chauffage) change automatiquement afin de conserver la
température programmée de manière constante.
Fonction pratique
MINUTERIE HEBDOMADAIRE
Utilisez cette fonction de minuterie pour régler les horaires de
fonctionnement pour chaque jour de la semaine.
Utilisez le réglage DAY OFF (Jour désactivé) pour
désactiver le fonctionnement programmé pour un jour sélec-
tionné de la semaine à venir. Comme tous les jours peuvent
être réglés ensemble, la minuterie hebdomadaire peut être
utilisée pour répéter les réglages de la minuterie pour tous les
jours.
MINUTERIE DE PROGRAMMATION DE LA
TEMPÉRATURE
Utilisez cette fonction de minuterie pour modifier la
température programmée dans les heures de
fonctionnement programmées pour chaque jour de la semaine.
Vous pouvez l'utiliser avec d'autres réglages de la minuterie.
FILTRE À AIR AMOVIBLE
Il est possible de retirer le filtre à air de l'appareil intérieur pour
un nettoyage et une maintenance faciles.
FILTRE RÉSISTANT ÀUX MOISISSURE
Le Filtre à air a reçu un traitement anti-moisissure, ce qui as-
sure sa propreté et la facilité de son entretien.
Télécommande
TÉLÉCOMMANDE AVEC FIL
La télécommande avec fil permet une commande pratique du
fonctionnement de l'appareil intérieur.
TÉLÉCOMMANDE SANS FIL (OPTION)
Il est possible d'utiliser la télécommande sans fil.
Lorsque vous utilisez la télécommande, les éléments
suivants sont différents de l'utilisation de la
télécommande avec fil.
[ Les fonctions supplémentaires pour les télécommandes sans
fil ]
• SLEEP (Temporisation)
• TIMER (MINUTERIE)
• MINIMUM HEAT (CHAUFFAGE MINIMUM)
Et vous pouvez utiliser les deux télécommandes avec et sans
fil simultanément. (Mais les fonctions sont limitées.)
[ Les fonctions restreintes pour les télécommandes avec fil ]
• Minuterie hebdomadaire
• Minuterie de la programmation de la température

Fonction économie d'énergie
et confortable
Fonction de nettoyage
9374379392-04_OM.indb 29374379392-04_OM.indb 2 9/6/2010 10:36:35 AM9/6/2010 10:36:35 AM

Fr-3
NOMENCLATURE DES ORGANES
1
Filtre à air (dans la grille d’aspiration)
2Clapets de direction
3Grille d’aspiration
4
Télécommande (filaire)
5
Panneau des commandes
6
Récepteur de signal de la télécommande
7
Touche MANUAL AUTO (MANUEL AUTO)
●
Lors de la pression prolongée du bouton MANUAL
AUTO pendant plus de 10 secondes, l’opération
de refroidissement forcé démarre.
●
L'opération de refroidissement forcé est
utilisée au moment de l'installation. Des-
tinée uniquement à l'utilisation par des
techniciens agréés
.
●
Lors du démarrage imprévu de l'opération de
refroidissement forcé, appuyez sur le bouton
START/STOP pour arrêter l'opération.
●
Appuyez sur le bouton FILTER INDICATOR
RESET (réinitialisation voyant filtre)
.
8Voyant OPERATION (vert)
9Voyant TIMER (FILTRE)
●
Le voyant TIMER s'allume lorsque la minuterie est
réglée pour la télécommande sans fil.
0Voyant indicateur ECONOMY (vert)
●
Le voyant indicateur ECONOMY s'allume lors du
fonctionnement en MODE ÉCONOMIQUE
et MODE CHAUFFAGE MINIMUM
.
1Touche START/STOP (mise en marche/arrêt)
2Touche SET TEMP. (régler la température)
3Touche MODE (commande principale)
4Touche FAN (commande du ventilateur)
5Touche ECONOMY (Economie)
6Touche TIMER MODE (REGLAGE DE L'HEURE)
7Bouton DAY (DAY OFF) (JOUR (JOUR ARRET))
8Bouton SET BACK (ABAISSER)
9Bouton Régler l’heure ( < > )
0
Touche TIMER DELETE (ANNULATION DE LA MINUTERIE)
A
Touche TIMER SET (REGLAGE DE LA MINUTERIE)
BBouton de va-et-vient et de direction du chemine-
ment de l’air vertical
CBouton de réglage de la direction horizontale du
flux d’air et d’oscillation horizontale (Cette fonction
n’est pas disponible)
DMAINTENANCE (REINITIALISATION DU FILTRE)#1
ELampe de fonctionnement
FAffichage de la minuterie et de l’horloge
GAffichage du mode de fonctionnement
HAffichage de la vitesse du ventilateur
IAffichage du verrou de fonctionnement
JAffichage de la température
KAffichage des fonctions
Affichage du dégivrage
Affichage du capteur thermique
Affichage ECONOMY (ÉCONOMIQUE)
Affichage du va-et-vient vertical
Affichage du filtre#1
#1:
Utilisable si correctement paramétré durant l'installation.
Veuillez consulter un dépanneur agréé en cas d'utilisation
de cette fonction.
Télécommande
I
H
G
J
K
E
1
C
5
D
A
0
3
4
B
8
6
2
F
9
7
FILAIRE
9374379392-04_OM.indb 39374379392-04_OM.indb 3 9/6/2010 10:36:35 AM9/6/2010 10:36:35 AM