Fujitsu FI-6670A Configuration guide

1
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
fi-6670(A) & fi-6770(A) CONSUMABLE
REPLACEMENT AND CLEANING INSTRUCTIONS
CG00002-015501C

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
2
CONSUMABLES LIST
Description Life Fujitsu P/N
Brake Roller 250,000 PA03576-K010
Pick Rollers 250,000 PA03338-K011
Note:
NCRorCarbonlesspaperhaschemical composition which damages
the Brake Roller and Pick Rollers. Cleaning of these items will be
neededmorefrequentlytoavoidfeedproblemsifscanningalarge
quantity of this type of paper. Also the consumable life will be reduced
if this paper is scanned.
PickRollers
Brake Roller

3
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE BRAKE ROLLER
• Whentheconsumableshave
fed250,000pagesthe
message to the right is
displayedonthecomputer
screen.
• Removeanydocuments
remainingintheADFPaper
Chute.
• Press the ADF Buttons to
release the lock and open the
ADF.
• OpentheBrakeRollerCover.
Aworn out or improperlyinstalledBrake Roller will causemultiplefeedsor
paperjams. The Brake Roller has anapproximatelifeof250,000 pages. If
NCR or carbonless paper is scanned the life span of the Brake Roller may
be decreased by as much as 50%.
Note:
It is very strongly recommended to replace the Brake Roller and Pick
Roller at the same time. This will insure the longest possible life for
eachconsumableitem.
IftheBrakeRoller and Pick Roller have been cleaned (refer tothecleaning
section of this document) they should be replaced if the scanner continues
to multi-feed or jam paper at a high rate.
ADF Buttons
Brake Roller Cover
Brake Roller Cover

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
4
REPLACING THE BRAKE ROLLER (CONT.)
• Lift the Brake Roller out of the
scanner.
• Pull the shaft out of the Brake
Roller.
• Install the shaft into the new
BrakeRoller.
Slots in Brake Roller Collar
Note:
When installing the shaft into the new Brake Roller, make sure to align
the tabs in the roller shaft with the slots on the collar of the Brake
Roller. Refertothephotos below.
Tabs in Brake Roller Shaft

5
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE BRAKE ROLLER (CONT.)
• Placethe new Brake Roller
intotheBrakeRollerCover,
making sure to align the flat
areaoftheBrake Roller shaft
intheguidegrooveofthe
BrakeRollerCover.
Note:
It is important to make sure that the shaft is at the bottom of the guide
grooveoftheBrake RollerCover.
• Close the Brake Roller Cover, making sure it snaps into place.
• Close theADF.
• Referto“ResettingTheConsumablesCounters” later in this document
toreset the Brake Roller Counter.

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
6
REPLACING THE PICK ROLLERS
Worn out, defective, or improperly installed Pick Rollers will cause mis-
feedsandpaper jams. The Pick Rollers have anapproximatelifeof
250,000pages. If NCR orcarbonlesspaper is scanned, thelifespan of
the Pick Rollers will be decreased by as much as 50%.
Note:
It is very strongly recommended to replace the Brake Roller and Pick
Roller at the same time. This will insure the longest possible life for
eachconsumableitem.
IftheBrakeRoller and Pick Roller have been cleaned (refer tothecleaning
section of this document) they should be replaced if the scanner continues
to multi-feed or jam paper at a high rate.
• Removeanydocuments
remainingintheADFPaper
Chute.
• Press the ADF Buttons to
release the lock and open the
ADF.
• Slideopen the Sheet Guides
onthePaper Chute, making
sure that they do not obstruct
thePickRollerCover.
• OpenthePickRollerCover.
• Slide the two Pick Rollers in
thedirectionofthe arrow and
lift them out of the scanner.
Note:
ThePickRollers are made
upof two rollers. The roller
with the treads going across
theroller is the Separation
Roller. Therollerwiththe
belt in the center is the Pick
Roller.
Separation Roller
Pick Roller
ADF Buttons

7
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE PICK ROLLERS (CONT.)
• InstallthenewSeparation
Roller onto the shaft. Make
sure to align the slot in the
roller collar with the screw in
theshaft.
• Install the new Pick Roller
onto the shaft.
Make sure belt is facing up.
• Make sure to align the slot in the roller collar with the screw in the
shaft.
• ClosethePickRollerCover.
• Close theADF.
• Referto“ResettingTheConsumablesCounters” later in this document
to reset the Pick Roller Counter.
Note:
Make sure that the belt is facing up and the wide plastic foot slides
intothegroove in the bottom oftherollercompartment.
Wide Plastic Foot
Groove

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
8
RESETTING THE CONSUMABLE COUNTERS
After the Brake Roller and the Pick Rollers have been replaced it is
important to reset the scanner consumable counters. These counters will
keep track of how many pages have been scanned since the last time the
consumableswerereplaced. Resetting these counters will insure that
the Brake Roller and the Pick Rollers are replaced before paper feed
problemsoccur.
• Confirm that the scanner and the PC are connected, and the scanner is
poweredon.
• Select [PROGRAMS] - [SCANNER UTILITY FOR MICROSOFT WINDOWS]-
[SOFTWARE OPERATION PANEL]from the [START] Menu.
• ThescreenbelowisdisplayeduponenteringtheSoftwareOperation
Panel.
•Press the
DEVICE SETTING
option in the left
pane.

9
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
RESETTING THE CONSUMABLE COUNTERS (CONT.)
• TheDeviceSettingScreenbelow is displayed.
• Press the CLEAR button next to the consumable that has been
replaced.
• Once the CLEAR buttons are pressed, press the OK button to clear the
counters.
• Press the OK button when asked to
“Write to EEPROM OK?” This will reset
thecounter and exit the Software
OperationPanel.

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
10
CLEANING LOCATIONS AND FREQUENCIES
Note:
More frequent cleaning is necessary when the following types of
documents are scanned:
• Paper with special chemical materials such as carbonless paper.
• Paper with large amount of printing. (Heavy toner or ink)
• Paper with pen ink or pencil lead.
• Documents with toner that is not fused properly.
• Paper with a smooth surface such as coated paper.
Location Tools Frequency
Cleaning Sheets Every 10,000 Sheets
Cloth & Isopropyl Alcohol Every 20,000 Sheets
Urethane Feed Rollers &
Plastic Feed Rollers
Transport Path Cloth & Isopropyl Alcohol Every 20,000 Sheets
ADF Glass Surfaces Cloth & Isopropyl Alcohol Every 20,000 Sheets
Every 20,000 Sheets
Scanned Through FB
Cloth & Isopropyl Alcohol
Flatbed Glass
Document Holding Pad
Cloth and F1 Cleaner Every 20,000 Sheets
Pick Rollers & Brake Roller
PickArm
CLEANING MATERIAL
Cleaning Item Part Number
F1 Cleaner CG90000-143401
Cleaning Cloths CG90000-120001
Cleaning Wipes PA03950-0419
Cotton Swabs CG90000-120601
Cleaning Paper CA99501-0012

11
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CLEANING THE PAPER PATH WITH THE CLEANING PAPER
• Turn offthescanner.
• Make sure the Sheet Guides
onthePaperChuteare
openedtotheirwidest
position.
• Press the ADF Buttons to
release the lock and open the
ADF.
• Take a Cleaning Paper and
sprayF1cleaner or isopropyl
alcohol on both sides.
• PlacetheCleaningPaper into
the ADF against either of the
SheetGuides.
TheCleaningPaper is designed to remove only loose paperdustandink
fromthe rollers. Use them approximately every10,000 sheetsscanned.
Using the cleaning paper does not take the place of the more
complete cleanings described later in this section
ADF Buttons

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
12
CLEANING THE PAPER PATH WITH THE CLEANING PAPER (CONT.)
• Close theADF and turn the
scanneron. TheCleaning
Paperwill be automatically
fedthroughtheADF.
• Repeattheabovesteps,
aligningtheCleaningPaper
againsttheopposite Sheet
Guide.
• TurntheCleaningPaperover(androtate)andrepeatthestepsabovea
numberoftimes.

13
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CLEANING THE ADF
Itis very important tocleanthe scanner feed componentsona regular
basistoavoid paper feeding problems. These itemsshouldbecleanedat
least every 20,000 sheets. Daily cleaning may be required if carbonless
paperorpaper with large amounts of toner andinkarefed.
• Press the ADF Buttons to
release the lock and open the
ADF.
CLEANING THE PICK ARM
Adirty PickArm can cause mis-feeds, paper jams, and also damage or
markthepaper.
• Clean the PickArm with a
dry, lint free cloth or a cloth
moistenedwithF1Cleaneror
isopropylalcohol.
CLEANING THE BRAKE ROLLER
A dirty Brake Roller can cause multi-feeds and paper jams.
• OpentheBrakeRollerCover,
andremovetheBrakeRoller.
• CleantheBrake Roller by
wiping across the surface of
the rollers with a lint free
cloth moistened with F1
Cleanerorisopropylalcohol.
• Reinstallthe Brake Roller.
PickArm
ADF Buttons

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
14
CLEANING THE ADF(CONT.)
CLEANING THE PICK ROLLERS
Dirty Pick Rollers can cause mis-picks, paper jams, and multi-feeds.
• OpenthePickRollerCover
andremovethe Separation
Roller and the Pick Roller.
• CleantheSeparationRoller
by wiping across the surfaces
of the rollers with a lint free
cloth moistened with F1
Cleanerorisopropylalcohol.
• Clean the Pick Roller by
wipingacrossthe surfaces of
each Pick Roller with a lint
freecloth moistened with F1
Cleanerorisopropylalcohol.
• Also, make sure to clean the
belt in the center of the Pick
Roller with a lint free cloth
moistenedwithF1Cleaneror
isopropylalcohol.
• Reinstall the Pick Rollers.
Separation Roller
Pick Roller

15
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CLEANING THE ADF(CONT.)
CLEANING THE ADF ROLLERS
DirtyADF Rollers will cause frequent jams.
• Clean the two sets of
UrethaneRollerswitha lint
freecloth moistened with F1
Cleanerorisopropylalcohol.
Both of these sets of rollers
are located on the top section
of theADF.
Note:
Toproperlycleanthecomplete surfaces of the rollers holddownthe
[SENT TO]and SCAN Buttons on the Operator Panel simultaneously. The
rollers will rotate to a new position.
• Clean the two sets of Plastic Rollers with a lint free cloth moistened
with F1 Cleaner or isopropyl alcohol. Both of these sets of rollers are
located on the bottom section of theADF.
CLEANING THE TRANSPORT PATH
Dirty Sheet Guides can cause paper jams, and also damage or mark the
paper. Dirty GlassAreas can cause image quality problems such as
verticalstreaking,orfadedimage.
• Wipe the two glass areas
(upperandlower),andthe
two sheet guides with a lint
freecloth moistened with F1
Cleanerorisopropylalcohol.
Glass Areas
Sheet Guides
Urethane Feed Rollers
Plastic Rollers
Check
Function
Send to
Scan / Stop Power
[Send to] Button
[Scan] Button
Check
Function
Send to
Scan / Stop
Power
[Send to] Button
[Scan] Button
fi-6670(A) fi-6770(A)

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
16
CLEANING THE FLATBED (fi-6770)
It is important to keep the Flatbed area clean. Adirty Flatbed Glass can
cause spots or unclear images. If there are marks on the Document
Holding Pad, these marks can appear on the image when scanning thin
sheetsofpaper.
• OpentheDocumentCoverby
pressingtheOpen/Close
Leverandlifting.
• Clean the Flatbed Glass with
a lint free cloth moistened
withF1Cleanerorisopropyl
alcohol. Make sure not to
leave any streaks on the
glass.
• CleantheDocumentHolding
Pad with a lint free cloth
moistenedwithF1Cleaneror
isopropylalcohol.
• ClosetheDocumentCover.
Flatbed Glass
Document Holding Pad

17
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CLEANING NOTIFICATION
Thefi-6670andfi-6770scannerscanbeconfiguredto display a cleaning
notificationon the computer screen. Thisnotificationcan be configured to
display at user selected intervals. This will alert the user to clean the
scanner.
CONFIGURING CLEANING NOTIFICATION
• Confirm that the scanner and the PC are connected, and the scanner is
poweredon.
• Select [PROGRAMS] - [SCANNER UTILITY FOR MICROSOFT WINDOWS]-
[SOFTWARE OPERATION PANEL]fromthe[START] Menu.
• ThescreenbelowisdisplayeduponenteringtheSoftwareOperation
Panel.
•Press the
CLEANING CYCLE
option in the left
pane.

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
18
CLEANING NOTIFICATION (CONT.)
• Click on the SHOW CLEANING INSTRUCTIONS check box.
• Selectthepageinterval of when the Cleaning Notification isdisplayed.
10,000pagesisrecommended.
Note:
Morefrequentcleaningmay be necessary depending on what type of
paperisscanned.
• The following screen is displayed, notifying the user that it is time to
cleanthescanner.
CLEARING THE CLEANING COUNTER
.

19
fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CLEARING THE CLEANING COUNTER
Afterthescanner is cleaned, the Cleaning Countershouldbecleared.
• OpentheSoftwareOperationPanel.
• Press the DEVICE SETTING option in the left pane.
• Press the CLEAR button next to theAfter cleaning counter.
• Once the CLEAR buttons are pressed, press the OK button to clear the
counters.
• Press the OK button when asked to
“Write to EEPROM OK?” This will reset
thecounter and exit the Software
OperationPanel.

fi-6670(A)&fi-6770(A)CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
20