Fujitsu PRIMERGY CX122 S1 User manual

Operating Manual - English
PRIMERGY CX122 S1
Server
Operating Manual
Edition November 2010

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
email: [email protected].
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2010 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other
rights arising from the use of any information in this manual.
– No part of this manual may be reproduced in any form without the prior written
permission of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

CX122 S1 Operating Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the product
is used in a hot environment. The customer shall bear the cost of replacing
replaceable components which have exceeded their operating life. Note that
these are only guidelines, and do not constitute a guarantee of trouble-free
operation during the maintenance support period.
High safety use
This product has been designed and manufactured for general uses such as
general office use, personal use, domestic use and normal industrial use. It has
not been designed or manufactured for uses which demand an extremely high
level of safety and carry a direct and serious risk to life or body if such safety
cannot be ensured.

Operating Manual CX122 S1
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance control
in weapons systems (hereafter, "high safety use"). Customers should not use
this product for high safety use unless measures are in place for ensuring the
level of safety demanded of such use. Please consult the sales staff of Fujitsu if
intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market:
About SATA hard disk drives
The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://primeserver.fujitsu.com/primergy/harddisk/

CX122 S1 Operating Manual
Contents
1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1 Concept and target groups for this manual . . . . . . . . . . 7
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 8
1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . 10
1.5 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . 11
2 Installation steps, overview . . . . . . . . . . . . . . . . . . 15
3 Important information . . . . . . . . . . . . . . . . . . . . . 17
3.1 Information for ensuring electromagnetic compatibility . . . 17
3.2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 17
3.3 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.4 FCC Class A Compliance Statement . . . . . . . . . . . . . 22
3.5 Environmental protection . . . . . . . . . . . . . . . . . . . 23
4 Hardware installation . . . . . . . . . . . . . . . . . . . . . . 25
4.1 Installation Procedure . . . . . . . . . . . . . . . . . . . . . 26
4.2 Installing / replacing a PRIMERGY CX122 S1 server . . . . . 27
4.2.1 Removing a PRIMERGY CX122 S1 server . . . . . . . . . . . 27
4.2.2 Installing a PRIMERGY CX122 S1 server . . . . . . . . . . . . 29
4.3 Connecting devices and cables . . . . . . . . . . . . . . . . 32
4.3.1 Connecting devices . . . . . . . . . . . . . . . . . . . . . . . 33
4.3.2 Connecting / disconnecting cables . . . . . . . . . . . . . . . 33
4.3.2.1 Network cabling . . . . . . . . . . . . . . . . . . . . . . . 34
5 Starting up and operation . . . . . . . . . . . . . . . . . . . 39

Operating Manual CX122 S1
5.1 LAN indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5.2 Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.2.1 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.2.2 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.3 Switching the server on and off . . . . . . . . . . . . . . . . 44
5.3.1 Switching the server on . . . . . . . . . . . . . . . . . . . . . . 44
5.3.2 Switching the server off . . . . . . . . . . . . . . . . . . . . . . 45
5.4 Configuring the server . . . . . . . . . . . . . . . . . . . . . 45
5.4.1 Operating system installation . . . . . . . . . . . . . . . . . . . 45
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

CX122 S1 Operating Manual 7
1 Preface
The new PRIMERGY CX1000 rack server system is
tailored to the needs of internet service providers: The
cost and energy efficient architecture provides the
highest server density per square meter with
maximum reliability. Thanks to the centralized
innovative cooling approach and front side connection
panels PRIMERGY CX1000 system units can be set
up 'back to back' requiring less datacenter floor space.
PRIMERGY CX122 S1 server nodes for use with the
CX1000 rack infrastructure are all-purpose servers
with top dual processor performance for cloud
computing data centers. Despite the compact form
factor, each PRIMERGY CX122 S1 server offers
eighteen DDR3 memory slots for up to 144 GB of RAM
and up to two 2.5-inch SATA hard disk drives.
1.1 Concept and target groups for this manual
This manual will familiarize you with the controls and indicators of your
PRIMERGY CX122 S1 server nodes.
The operating manual is aimed at those responsible for installing the hardware
and ensuring the proper operation of the system. To understand the concepts
described in this manual, you will need to be familiar with the fields of hardware
and data transmission.

8 Operating Manual CX122 S1
Documentation overview
1.2 Documentation overview
More information on your PRIMERGY CX122 S1 can be found in the following
documents:
– "Quick Start Software - Quick Installation Guide" DVD booklet
(only included with the ServerView Suite as a printed copy) except for the
Japanese market
– "Safety notes and regulations" manual
"安全上のご注意 " for the Japanese market
– "Warranty" manual
"保証書 " for the Japanese market
– "ServerView Suite Local Service Concept - LSC" manual
– "Returning used devices" manual and "Service Desk" leaflet
"サポート＆サービス " for the Japanese market
– "PRIMERGY CX122 S1 Server Operating Manual"
– "System Board D2899 for PRIMERGY CX122 S1 Technical Manual"
Information of CX1000 can be found in the following documents:
– PRIMERGY CX1000 S1 System Unit PRIMERGY CX120 S1 Server
Operating Manual
IPRIMERGY manuals are available in PDF format on the
ServerView Suite DVD 2. The ServerView Suite DVD 2 is part of the
ServerView Suite supplied with every server.
If you no longer have the ServerView Suite DVDs, you can obtain the
relevant current versions using the order number U15000-C289 (the
order number for the Japanese market: please refer to the configurator
of the server http://primeserver.fujitsu.com/primergy/system.html).
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL (for EMEA market):
http://manuals.ts.fujitsu.com. The PRIMERGY server documentation can
be accessed using the Industry standard servers navigation option.
For the Japanese market please use the URL:
http://primeserver.fujitsu.com/primergy/manual.html.

CX122 S1 Operating Manual 9
Features
Further sources of information:
– PRIMERGY Abbreviations and Glossary on the ServerView Suite DVD 2
– Operating system documentation
1.3 Features
High Capacity
Up to 38 PRIMERGY CX122 S1 server nodes can be installed into a
PRIMERGY CX1000 system units.
Ventilation and Power Supply
The centralized PRIMERGY CX1000 chimney ventilation concept allows
operation of up to 38 passively cooled server nodes with only two large radial
fans installed on top of the rack cabinet. The design purpose is the most efficient
cooling of the server nodes using the minimum of electrical energy to move air.
The fans, mounted at the top of the rack, do not cool the servers directly, but
exhaust air from a low pressure chamber which subsequently draws the air
through the servers. The control of the fans is an autonomous function (see
"Rack Management Unit (RMU)" operating manual) and serves to maintain a
constant under-pressure in this chamber.
System Board
The hardware and BIOS features of the PRIMERGY CX122 S1 system board
are described in the technical manual for the system board D2899 and the BIOS
manual.
Expansion Cards
Each PRIMERGY CX122 S1 server node provides one riser slot (PCIe Gen2
x16 ).
Hard Disk Drives
The PRIMERGY CX122 S1 server node can be ordered with up to two 2.5-inch
SATA hard disk drives.

10 Operating Manual CX122 S1
Notational conventions
Serviceability and Support
Operating and maintaining your PRIMERGY CX1000 S1 rack server system is
easy: CX122 S1 server nodes are lightweight, mounted on slide rails with front
accessible network ports. The highly efficient power supply connects cordlessly
to the power distribution unit in the rack. The fanless node cooling concept
allows for virtually wear-free operation.
1.4 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

CX122 S1 Operating Manual 11
Technical data
1.5 Technical data
Electrical data
Rated voltage range 200 V - 240 V
Rated frequency 50 Hz - 60 Hz
Max. rated current 200 V - 240 V / 2.0 A
Rated current X5500 series CPUs 200 V - 240 V / 1.8 A
Rated current E5500 series CPUs 200 V - 240 V / 1.0 A
Rated current L5500 series CPUs 200 V - 240 V / 0.8 A
Rated current idle mode 200 V - 240 V / 0.3 A
(depending on configuration / application)
Effective power
(X / E / L series CPUs)
286 W / 192 W / 185 W
(depending on configuration / application)
Apparent power
(X / E / L series CPUs)
302 VA / 206 VA / 200 VA
(depending on configuration / application)
Heat dissipation
(X / E / L series CPUs)
1029 KJ/h (975 btu/h)
691 KJ/h (654 btu/h)
666 KJ/h (631 btu/h)
Main power fuse EMEA 16 A
Main power fuse NORAM 20 A
Protection class I

12 Operating Manual CX122 S1
Technical data
Compliance with regulations and standards
Mechanical values
Product safety and ergonomics
International IEC 60950-1/2
Europe EN 60950-1/2
EN 50371
USA / Canada UL/CSA 60950-1/2
Taiwan CNS 14336
USA / Canada GB 4943
Electromagnetic compatibility
International AS / NZS CISPR22 Class A
Europe CE Class A
EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
ETSI EN 300386
USA / Canada FCC Class A
ICES-003 Class A
Taiwan CNS 13438 Class A
China CCC (GB 9245 / GB 17625)
Japan VCCI Class A
CE marking to EU
directives
Low Voltage Directive: 2006/95/EC
Electromagnetic compatibility: 2004/108/EC
Width 483 mm (front panel)
Depth 454 mm
Height 42 mm / 1 HU
Weight 6.5 kg (depending on the configuration)

CX122 S1 Operating Manual 13
Technical data
Ventilation clearance
Ambient conditions
Noise level
Front min. 200 mm
Rear min. 200 mm
Environment class 3K2
Environment class 2K2
DIN IEC 721 section 3-3
DIN IEC 721 section 3-2
Ambient temperature 10°C - 35°C (DIN IEC 721-3-3) class 3K2,
ETSI 300 019-2-3 Class 3.1
Temperature:
Operation (3K2) 10 °C ... 35 °C
Transport (2K2) -25 °C ... 60 °C
Humidity 10% ... 85% RH non-condensing
Condensation during operation must be avoided!
Conditions of use
Air quality
The system complies with regulation Class 3S2
according to DIN EN 60721-3-3 (for product
class B).
Sound power level LWAd (ISO 9296) SATA sub-system
(no active cooling)
Sound pressure level at adjacent position
LpAm (ISO 9296)
SATA sub-system
(no active cooling)

14 Operating Manual CX122 S1
Technical data

CX122 S1 Operating Manual 15
2 Installation steps, overview
This chapter contains an overview of the steps you need to carry out in order to
set up your server. Links take you to sections where you can find more detailed
information about the respective steps:
ÊFirst of all, it is essential that you familiarize yourself with the safety
information in chapter "Important information" on page 17.
ÊYour PRIMERGY CX1000 system has been unpacked and set up by a
Fujitsu service technician.
Make sure that the accompanying documentation (see "Documentation
overview" on page 8) is complete. Print out the required PDF files, if
necessary.
ÊFamiliarize yourself with the controls and indicators on the front of the
CX122 S1 server nodes, (see section "LAN indicators" on page 39 and
section "Front panel" on page 41).
ÊConfigure the server and install the desired operating system and
applications (see section "Configuring the server" on page 45).

16 Operating Manual CX122 S1

CX122 S1 Operating Manual 17
3 Important information
In this chapter you will find essential information regarding safety when working
on your server.
3.1 Information for ensuring electromagnetic
compatibility
●All data and signal cables must have sufficient shielding
●The LAN cabling must be conform with the requirements EN 50173 and EN
50174-1/2.
●Use of unshielded or badly shielded cables may led to increased emission
of interference and/ore reduced faulty-tolerance of the device
3.2 Safety instructions
IThe following safety instructions are also provided in the manual "Safety
Notes and Regulations".
This device meets the relevant safety regulations for IT equipment. If you have
any questions about whether you can install the server in the intended
environment, please contact your sales outlet or our customer service team.
VCAUTION!
●The actions described in this manual shall be performed by technical
specialists. A technical specialist is a person who is trained to install
the server including hardware and software.
●Repairs to the device that do not relate to CSS failures shall be
performed by service personnel. Please note that unauthorized
interference with the system will void the warranty and exempt the
manufacturer from all liability.
●Any failure to observe the guidelines in this manual, and any improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.

18 Operating Manual CX122 S1
Safety instructions
●Keep this operating manual and the other documentation (such as the
technical manual, CD) close to the device. All documentation must be
included if the equipment is passed on to a third party.
Before starting up
VCAUTION!
●When installing the appliance and before placing it in service, please
take note of the information on the required ambient conditions and
the required technical infrastructure. The information you require here
is contained in section "Technical data" on page 11.
VCAUTION!
●When relocating the appliance: If the device is brought in from a cold
environment, condensation may form both inside and on the outside
of the device. Wait until the device has acclimatized to room
temperature and is absolutely dry before starting it up. Material
damage may be caused to the device if this requirement is not
observed.
●Installation, mounting and removal activities involving the CX1000
system unit may only be performed by technicians, service personnel
or technical specialists. Ignoring the instructions in this manual can
result in personal injury or damage to equipment (risk of tipping over,
etc.).
●When the unit is transported, it is only allowed to have a lean angle of
max. 15°.
●Make sure that the floor at the final place of installation has sufficient
load-bearing capacity.
●Route the cables in such a way that they do not form a potential
hazard (make sure no one can trip over them) and that they cannot
be damaged.
●For safety reasons, no more than one unit may be withdrawn from the
rack at any one time during installation and maintenance work.
Please keep in mind, that PRIMERGY CX122 S1 server nodes will tip
over or fall out of the rack if slid out too far!
●The rack must be connected to the power supply by an authorized
specialist (electrician).

CX122 S1 Operating Manual 19
Safety instructions
●If necessary, have other people help you mount the individual
components in the rack because of the weight involved.
●Install only system expansions that satisfy the requirements and rules
governing safety. If you install other expansions, you may damage the
system or violate these safety regulations. Information can be
obtained from customer service or your local sales office.
●The AC main power connection for the PRIMERGY CX1000 system
unit must be installed by an authorized electrician approved by the
local utility company.
Installation and operation
VCAUTION!
General
●Make sure that no objects (e.g. jewelry, paperclips etc.) or liquids can
get inside the server (risk of electric shock, short circuit).
●Data cables must be adequately shielded.
●The EN 50173 and EN 50174-1/2 standards apply for LAN cabling.
The minimum requirement is the use of a category 5 screened LAN
cable for 10/100 Mbit/s Ethernet, or a category 5e cable for Gigabit
Ethernet. The requirements from the ISO/IEC 11801 specification
must also be met.
●Route the cables in such a way that they do not create a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting the server, refer to the relevant
instructions in this manual.
●Never connect or disconnect data transmission lines during a storm
(risk of lightning strike).
●In emergencies (e.g. damaged casing, controls or cables, penetration
of liquids or foreign bodies), switch off the server immediately, remove
all power plugs and contact your sales outlet or customer service
team.

20 Operating Manual CX122 S1
Safety instructions
PRIMERGY CX122 S1
●The On/Off button does not isolate the device from the mains power
supply. To disconnect it completely from the CX1000 power
distribution unit, loosen the two knurled screws on the server front
and slide the server out of the rack about 10 centimeters.
●Proper operation of the system (in accordance with IEC 60950-1/
EN 60950-1) is only ensured if the casing is completely assembled
and the slot brackets of the installation slots have been fitted (electric
shock, cooling, fire protection, interference suppression).
●When removing a PRIMERGY CX122 S1 server from the system
unit, always install a dummy cover in the empty installation bay.
●Only install system expansions that satisfy the requirements and
rules governing safety and electromagnetic compatibility and those
relating to telecommunication terminals. If you install other
expansions, they may damage the system or violate the safety
regulations. Information on which system expansions are approved
for installation can be obtained from our customer service center or
your sales outlet.
●The components marked with a warning notice (e.g. lightning symbol)
may only be opened, removed or exchanged by authorized, qualified
personnel.
●A defective PRIMERGY CX122 S1 server node is maintained by
Fujitsu service technicians. The warranty is void if the server is
damaged during installation or replacement of system expansions.