Fujitsu PRIMERGY DX920 S3 Manual

PRIMERGY BX920 S3
System configurator and order-information guide
Contents
Instructions
Configuration diagram
Configurator
0 System software
#XBX920 S3 Dual Socket 20 XX
#XI Processor 21 XXI
#XII Memory 22 XXII
#XIII Storage 23 XXIII
#XIV RAID Functionality 24 XXIV
#XV iRMC S3, Graphics 25 XXV
#XVI Mezzanine Cards 26 XXVI
#
#L
Storage Blades
#LI SX910 Tape Blade #LIV SX940 Storage Blade Disk
#LII SX910 SAS Controller #LV SX940 SAS Controller
#LIII SX910 SAS Tape Drive #LVI SX940 Quad Disk Blade
Change report
PRIMERGY Server
January 2014

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
System-Architect.
Only the tool "System-Arcitect" will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
Please pay attention to the naming conventions: BX900 S1 System unit 1nd generation
BX920 S2 Dual Server Blade S2
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/ System-Architect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
IV Memory, example
There are 3 free memory banks available.
The memory banks can be populated with 512MB, 1GB, 2GB and 4GB DDR Memory.
The maximum total amount of memory is 12GB.
It is possible to select memory upgrade options up to 3 times.
ECC with memory scrubbing-function and hot-spare memorybank is standard on the PRIMERGY BX600 S2 Server Blades.
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB
Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 3x) as the arrow indicates. 3x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html
(internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/Pages/Currentconfigurators.aspx
(extranet)
Prices and availability see price list and PC-/ System-Architect
Subject to change and errors excepted
Fujitsu PRIMERGY Server 2 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
Configuration diagram Dual Server Blade BX920 S3
Mezzanine slot 1
upper
CPU1 Row 1 (3 DIMMS) SAS 2.5"
or HDD dummy frame
Intel CPU First Mezz. card lower
Row 2 (3 DIMMS) or SAS 2.5"
unpopulated or HDD dummy frame
Mezzanine slot 2
Disk drives
CPU2 Row 1 (3 DIMMS) LSI HW Raid Ctrl.
Second Mezz. card
Intel CPU or Flash Backup Unit
Row 2 (3 DIMMS) unpopulated
PCH SAS upgrade
UFM
Processor Memory Mezzanine slot Storage Options
Key:
Included in basic unit Option
The population order for the CPU is: CPU1 first, then CPU2
The population order for the DIMMs: for each CPU, the DIMM row 1 (DIMMS 1A 1B 1C) (DIMMS 1D 1E 1F) first, then row 2 (DIMMs 2A, 2B, 2C) (DIMMs 2D, 2E, 2F)
Fujitsu PRIMERGY Server 3 of 14

System configurator and order-information guide
D
PRIMERGY BX920 S3 Status: 2013-12-30
Section
XDual Socket Server Blade BX920 S3
Server Blade with:
- Dual INTEL Romley Processor Support as Dual/Quad/Six-Core
- The base units with INTEL Processor
- 12 DIMM sockets, organized in 2 row (6 DIMM) for CPU1 and 2 row (6 DIMM) for CPU2
- 1x Dual channel 10 Gbit Ethernet CNA controller on-board
- Hard disk controller for the 2x SAS/SATA HDD/SSD
- 2 bays for 2.5" SAS hard disks (hot-plug)
- iRMC S3 on-board
- 1x front side USB connector
- Special connector for Y-cable (2x USB, 1x VGA).
The BX920 S3 Server Blade can be installed max. 18x in the BX900 S1 System Unit
S26361-K1406-V200 S26361-F4478-L2
PY BX920 S3 Dual Server Blade PY BX900 Y-Cable frontside
up to 2x 2.5" SAS/SATA hard disk drives. for KVM connection to
Dual Server Blade Base Unit without Server Blade
max. 18x
CPU and without memory modules! 2x USB, 1x VGA
PY BX920 S3 Dual Server Blade
For CPU and Memory configuration see section XLI.
Max. 18x per BX900 System Unit.
S26361-F3552-E1
TPM Module
Trusted Platform Module on motherboard
PY TPM Module
Be aware of import restrictions!
Max. 1x per Server Blade.
S26361-F2749-E1 S26361-F2749-E2
Service for Server Blade installation in the System Unit. Server Blade individually packed / delivered.
Hereby the BX900 will be delivered completely
The Server Blade is not built in a BX900,
configured and tested with Server Blades integrated.
it is separately tested and delivered.
This order number must be in the same order as the System Unit itself.
Contains ServerStart CD
min. 1x per System Unit; max. 18x per System Unit; max. 1x per Server Blade max. 1x per Server Blade
E
Fujitsu PRIMERGY Server 4 of 14

E
System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
Section
XI
Processor
There are 2 processor sockets available.
The first socket is always equipped with the first CPU which can be selected via configurator
It is also possible to upgrade a dual-processor system later on with a second CPU
For the second CPU there are different order numbers, due to the different Heatsink.
Two processors with different clock frequencies are not possible
A multi-processor operating system is required for a dual-processor system.
Max. two CPU`s can be selected per basic unit
One of following CPU´s has to be selected as first CPU
for an orderable basic unit
Optional second CPU has to be the same type like the first CPU
Basic 4C CPU's
- 1x 64-bit Intel Xeon (10MB shared TLC = Third Level Cache )
1066 MHz DDR3 Bus, 6,40 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2403 4C/4T 1.80GHz 10MB 6.40GT/s 1066MHz 80W S26361-F4560-E180
Xeon E5-2407 4C/4T 2.20GHz 10MB 6.40GT/s 1066MHz 80W S26361-F4560-E220
Standard Turbo 6C CPU's
- 1x 64-bit Intel Xeon (15MB shared TLC = Third Level Cache ); Hyper-Threading (HT);
1333 MHz DDR3 Bus, 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
1x Xeon E5-2420 6C/12T 1.90GHz 15MB 7.20GT/s 1333MHz 95W S26361-F4561-E190
Xeon E5-2430 6C/12T 2.20GHz 15MB 7.20GT/s 1333MHz 95W S26361-F4561-E220
Xeon E5-2440 6C/12T 2.40GHz 15MB 7.20GT/s 1333MHz 95W S26361-F4561-E240
Advanced Turbo+ 8C CPU`s
- 1x 64-bit Intel Xeon (20MB shared TLC = Third Level Cache ); Hyper-Threading (HT);
1600 MHz DDR3 Bus, 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2450 8C/16T 2.10GHz 20MB 8.00GT/s 1600MHz 95W S26361-F4562-E210
Xeon E5-2470 8C/16T 2.30GHz 20MB 8.00GT/s 1600MHz 95W S26361-F4562-E230
Low Power 6C/8C CPU's
- 1x 64-bit Intel Xeon (15/20MB shared TLC = Third Level Cache); Hyper-Threading (HT);
1333/1600 MHz DDR3 Bus, 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2430L 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 60W S26361-F4563-E200
Xeon E5-2450L 8C/16T 1.80GHz 20MB 8.00GT/s 1600MHz 70W S26361-F4563-E180
Max. two CPU`s can be selected per basic unit
One of following CPU´s has to be selected as second CPU
for an orderable basic unit
Optional second CPU has to be the same type like the first CPU
Basic 4C CPU's
- 1x 64-bit Intel Xeon (10MB shared TLC = Third Level Cache )
1066 MHz DDR3 Bus, 6,40 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2403 4C/4T 1.80GHz 10MB 6.40GT/s 1066MHz 80W S26361-F4564-E180
Xeon E5-2407 4C/4T 2.20GHz 10MB 6.40GT/s 1066MHz 80W S26361-F4564-E220
Standard Turbo 6C CPU's
- 1x 64-bit Intel Xeon (15MB shared TLC = Third Level Cache ); Hyper-Threading (HT);
1333 MHz DDR3 Bus, 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
1x Xeon E5-2420 6C/12T 1.90GHz 15MB 7.20GT/s 1333MHz 95W S26361-F4565-E190
Xeon E5-2430 6C/12T 2.20GHz 15MB 7.20GT/s 1333MHz 95W S26361-F4565-E220
Xeon E5-2440 6C/12T 2.40GHz 15MB 7.20GT/s 1333MHz 95W S26361-F4565-E240
Advanced Turbo+ 8C CPU`s
- 1x 64-bit Intel Xeon (20MB shared TLC = Third Level Cache ); Hyper-Threading (HT);
1600 MHz DDR3 Bus, 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2450 8C/16T 2.10GHz 20MB 8.00GT/s 1600MHz 95W S26361-F4566-E210
Xeon E5-2470 8C/16T 2.30GHz 20MB 8.00GT/s 1600MHz 95W S26361-F4566-E230
Low Power 4C/6C/8C CPU's
- 1x 64-bit Intel Xeon (15/20MB shared TLC = Third Level Cache); Hyper-Threading (HT);
1333/1600 MHz DDR3 Bus, 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2430L 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 60W S26361-F4567-E200
Xeon E5-2450L 8C/16T 1.80GHz 20MB 8.00GT/s 1600MHz 70W S26361-F4567-E180
F
Fujitsu PRIMERGY Server 5 of 14

System configurator and order-information guide
FPRIMERGY BX920 S3 Status: 2013-12-30
Section
XII Storage
Mixed configurations with ECO SATA drives and SAS drives are not allowed
Mixed configurations BC-SATA/BC-SAS drives with SAS 10K (S26361-F4482-E130, S26361-F4482-E145,
S26361-F4482-E160) not allowed.
Configurations with Eco SATA can only be mixed with BC SATA HDD type
All combinations of SSD, BC SATA and SAS are possible - but not in same logical drive (RAID array)
Both hard disks are plugged in directly connected to the onboard controller.
One UFM can be configured in addition to the Hard Disks
Remark: UFM is part of the VMWare Embedded solution (S26361-F2341-E431)
Remark: Currently VMWare RAID configurations are not supported with the onboard PCH controller
SAS Drives require the SAS Option to enable PCH SAS connection
or the SAS RAID Option
S26361-F5225-E100 S26361-F5225-E200 S26361-F5225-E400
SSD SATA 100GB, MLC
SSD SATA 200GB, MLC SSD SATA 400GB, MLC
Solid State Disk
Solid State Disk
Solid State Disk
SATA 6Gb/s SATA 6Gb/s SATA 6Gb/s
Mainstream Perfomance
Mainstream Perfomance Mainstream Perfomance
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 2x per base unit max. 2x per base unit max. 2x per base unit
S26361-F4581-E100 S26361-F4581-E200 S26361-F4581-E400
SSD SAS 100GB, MLC SSD SAS 200GB, MLC SSD SAS 400GB, MLC
Solid State Disk
Solid State Disk
Solid State Disk
SATA 6Gb/s
SAS 6Gb/s
SATA 6Gb/s
Mainstream Perfomance
Enterprise Perfomance Mainstream Perfomance
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 2x per base unit max. 2x per base unit max. 2x per base unit
max 2x S26361-F3708-E250 S26361-F3708-E500 S26361-F3708-E100
HD 250GB 7.2krpm 2.5"
HD 500GB 7.2krpm 2.5"
HD 1000GB 7.2krpm 2.5"
7200rpm,<9,5ms, 64MB Cache 7200rpm,<9,5ms, 64MB Cache 7200rpm,<9,5ms, 64MB Cache
BC SATA 6Gb/s BC SATA 6Gb/s BC SATA 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 2x per base unit max. 2x per base unit max. 2x per base unit
S26361-F4482-E573 S26361-F4482-E514 S26361-F4482-E530
HD 73GB 15krpm 2.5" HD 146GB 15krpm 2.5" HD 300GB 15krpm 2.5"
15000rpm,<4,5ms, 8MB Cache 15000rpm,<4,5ms, 8MB Cache 15000rpm,<4,5ms, 8MB Cache
SAS 6Gb/s
SAS 6Gb/s
SAS 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 2x per base unit max. 2x per base unit max. 2x per base unit
S26361-F5247-E130 S26361-F5247-E145 S26361-F5247-E160
HD 300GB 10krpm 2.5" HD 450GB 10krpm 2.5" HD 600GB 10krpm 2.5"
10000rpm,<4,5ms, 64MB Cache 10000rpm,<4,5ms, 64MB Cache
10000rpm,<4,5ms, 64MB Cache
SAS 6Gb/s
SAS 6Gb/s
SAS 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 2x per base unit max. 2x per base unit max. 2x per base unit
S26361-F4482-E190 S26361-F5247-E190 S26361-F5228-E500
HD 900GB 10krpm 2.5" HD 900GB 10krpm 2.5" HD 500GB 7.2krpm 2.5"
10000rpm,<4,5ms, 8MB Cache 10000rpm,<4,5ms, 64MB Cache 7200rpm,<4,5ms, 64MB Cache
SAS 6Gb/s
SAS 6Gb/s
BC SAS 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 2x per base unit max. 2x per base unit max. 2x per base unit
S26361-F5228-E100
HD 1TB 7.2krpm 2.5"
7200rpm,<4,5ms, 64MB Cache
BC SAS 6Gb/s
hot plug/hot replace tray
max. 2x per base unit
S26361-F4482-E130 S26361-F4482-E145 S26361-F4482-E160
HD 300GB 10krpm 2.5" HD 450GB 10krpm 2.5" HD 600GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache 10000rpm,<4,5ms, 8MB Cache 10000rpm,<4,5ms, 8MB Cache
SAS 6Gb/s
SAS 6Gb/s
SAS 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 2x per base unit
max. 2x per base unit max. 2x per base unit
F1
Fujitsu PRIMERGY Server 6 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
F1
Section
XIII RAID Functionality on Server Blade
The Dual Server Blade supports different RAID soltutions for internal HDD's
1. PCH based RAID
2. PCH based RAID with SAS upgrade
3. SAS RAID HDD Module with LSI HW RAID w/o cache
4. SAS RAID HDD Module with LSI HW RAID w/ 512 MB Cache and optional FBU
Also the SAS BP has to be changed. It is included in the RAID Mezz HDD Connection Kit.
Configuration Hint - Second CPU needed for SAS RAID Modules or SX910/940/960
The SAS RAID Modules are only supported if second CPU is installed
The connection to the SX910/SX940/SX960 is only supported if second CPU is installed
This upgrade is required to
add SAS support to the PCH controller
LSI
Patsburg B
RAID 0, 1 & 10
max. 1x per Server Blade
S26361-F4531-E513 S26361-F4531-E300
PY SAS RAID HDD Module
PY SAS RAID HDD Module
w/ 512 MB Cache w/o Cache
MegaRAID MegaRAID (iMR)
RAID level 0/1/1E/10/5/50/6/60 RAID level 0/1/10
SAS 6Gb/sec
SAS 6Gb/sec
pluggable on the main board pluggable on the main board
PCIe Gen3 interface
PCIe Gen3 interface
4x SAS links to midplane 4x SAS links to midplane
2x SAS links to internal HDD's 2x SAS links to internal HDD's
max. 1x per Server Blade max. 1x per Server Blade
1 x
S26361-F4531-E10
RAID FBU Upgrade
Flash Backup Unit
max. 1x per Server Blade
The SAS Expander Mezz Card
must be used in order
to establish the connection
to the SAS CB with the
PY SAS RAID HDD Module
S26361-F4531-E513 or
PY SAS RAID HDD Module w/o cache
S26361-F4531-E300
S26361-F4531-E50
RAID HDD Module Connection Kit
2x SAS HDD BP
max. 1x per Server Blade
G
no PCI slot required
S26361-F3674-E1
Onboard Controller SAS upgrade
no controller cache
SAS 3Gb/sec
4 internal ports
PCIe x4
Fujitsu PRIMERGY Server 7 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
G
Section
XIV
iRMC S3, Graphics
Graphic Controller is part of the onboard Management Controller iRMC S3.
Other graphics are not possible.
The iRMC S3 advanced pack is included in the system delivery.
A corresponding license order is not necessary.
Section
XV Mezzanine cards for Dual Socket Server Blade
The Dual Server Blade supports the following optional mezzanine cards.
A Fibre Channel Switch / Pass-Thru blade, an Ethernet LAN Switch / Pass-Thru blade,
respectively an InfiniBand switch is required in the system unit for this functionality.
SAS Mezz Cards require an SAS switch for each SAS link
SAS Mezz Cards have to be installed in Mezz Card slot 2 on Server Blade
S26361-F4480-E1 S26361-F4531-E30
SAS Expander Mezz Card
PY SAS HBA Mezz Card 6Gb PY SAS Expander Mezz. Card can only be used with
HBA for connectivity between PY SAS RAID HDD Module
SAS 2.0 SAS RAID HDD Module and S26361-F4531-E513
PCIe Gen2 interface SAS Connection Blade
1x 4x SAS links to midplane 4x SAS links to midplane
max. 1x per Server Blade max. 1x per Server Blade
S26361-F4531-E60
PY Enhanced Mezz Bracket/Riser
max. 1x per Server Blade
Requires an Ethernet LAN Requires a Fibre Channel Requires an InfiniBand
Switch, IBP or Pass-Thru Switch for each channel. Switch for each Mezz Card.
Blade for each channel.
S26361-F3331-E1 S26361-F3874-E1 S26361-F3992-E2 S26361-F4534-E1
PY Eth Mezz Card 1Gb 4 Port
PY FC Mezz Card 8Gb 2 Port
PY IB CX2 Mezz Card 40Gb 2 Port PY IB CX3 Mezz Card 56Gb 2 Port
2x Intel Zoar controller
Emulex LPe12002 compatible Interface to midplane: Interface to midplane:
4x 10/100/1000 Mbit/s. pluggable on the main board, 2x 10Gb/s(SDR), 2x 20Gb/s(DDR) 2x 10Gb/s(SDR), 2x 20Gb/s(DDR)
pluggable on the main board,
MC-FC82E 2x 40Gb/s(QDR)
2x 40Gb/s(QDR) 2x 56Gb/s(FDR)
four channel 1Gbit/s
Dual channel 8Gbit/s Dual channel 40Gbit/s each Dual channel 56Gbit/s each
PCIe x4 Interface PCIe x8 interface PCIe x8 interface PCIe x8 interface
max. 2x per Server Blade max. 2x per Server Blade max. 2x per Server Blade max. 2x per Server Blade
S26361-F3997-E1
PY Eth Mezz Card 10Gb 2 Port
Intel 82599EB LAN Controller
2x 10Gbit/s.
pluggable on the main board,
0 - 2x Dual channel 10Gbit/s
PCIe x8 Interface
max. 2x per Server Blade
S26361-F3592-E532
PY CNA Mezz Card 10Gb 2 Port
Emulex OCe11102 compatible
pluggable on the main board
MC-CNA112E
Dual channel 10Gbit/s
PCIe x8 Interface
max. 2x per Server Blade
R S T U V
R: see separate BX900 System Unit configurator, sheet "1 GB Ethernet"
S: see separate BX900 System Unit configurator, sheet "10 GB Ethernet"
T: see separate BX900 System Unit configurator, sheet "Fibre Channel"
U: see separate BX900 System Unit configurator, sheet "InfiniBand"
V: see separate BX900 System Unit configurator, sheet "CB SAS"
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx
Fujitsu PRIMERGY Server 8 of 14

System configurator and order-information guide
G
PRIMERGY BX920 S3 Status: 2013-12-30
Section
III Memory
- There are 6 memory slots per CPU for max.
192GB LRDIMM (6x 32GB 4R)
96GB RDIMM (6x 16GB 2R)
24GB UDIMM (6x 4GB)
=> max. 384GB for two CPU`s ( 192GB per CPU ), using LRDIMM
- The memory area is divided into 3 channels per CPU with 2 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2,
slot 3 belongs to memory bank 3
Registered, LR DIMMs and unbuffered memory modules can be selected
No mix of registered, load reduced and unbuffered modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed).
In a 2 DIMMs per channel configuration, following frequencies are supported:
- 1.5V - 1600MHz max (depending on CPU, special memory modules)
- 1.35V - 1333MHz max (depending on CPU)
SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only
1.) In the "Independent Channel Mode" is following configuration possible
Channels can be populated in any order in Independent Channel Mode. All four
channels may be populated in any order and have no matching requirements. All
channels must run at the same interface frequency but individual channels may run at
different DIMM timings (RAS latency, CAS latency, and so forth)
No mix of registered, load reduced and unbuffered modules allowed.
2.) "Rank Sparing Mode" configuration
- Within a memory channel, one rank is a spare of the other ranks.
The Spare Rank is held in reserve and is not available as system memory
For the effective memory capacity, please refer to the spreadsheet below.
The BIOS is set to the rank sparing setting.
Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel
This mode is not supported by x8 organized memory modules
3.) "Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 3x identical modules
4.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 4x registered or load reduced
In each memory bank channel Aand B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be
equipped with identical modules for mirrored channel mode.
In channel B is always the mirrored memory of channel A of CPU 1
In channel E is always the mirrored memory of channel D of CPU 2
Minimum configuration is: 2x identical modules
This mode is not supported by x8 organized memory modules
G1
Fujitsu PRIMERGY Server 9 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
G1
S26361-F3695-E10
Independent Mode
Independent Channel Mode allows all channels to be populated in anyorder. No specific Memory RAS features are defined
Requires min 1 memory Module per CPU
S26361-F3695-E1 Rank Sparing Mode Installation
BIOS Setup factory preinstalled to this mode. One Rankis spare of other ranks on the same channel. Spare Rank is not shown in System Memory.
For effective capacity within a channel, please have a look below.
Supported for RDIMM / LRDIMM only.
1x per CPU Requires min 2x 1R/2R or 1x 4R modules per CPU
S26361-F3695-E2 Performance Mode Installation
BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules
will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used.
Multiple of 3 identical modules to be configured per CPU
S26361-F3695-E3
Mirrored Channel Mode Installation
BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the
Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data
Supported for RDIMM / LRDIMM only.
Multiple of 2 identical modules to be configured per CPU
1R
2R
1R
2R
4R
4R
na na na na na
na na
Minimum one memory module or order code per CPU = first memory
Note 1.)
Unbuffered Memory (UDIMM) no SDDC (chipkill) support
Max. DDR3 memory speed depends on the memory configuration
- one DDR3 unbuffered ECC mem. Module, 1.35V
(No of mem modules per channe) as well as on the CPU type.
Choose up to 6 order codes per CPU The memory channel with the lowest speed defines the speed
of all CPU channels in the system, also for the channels of the
2GB (1x2GB) 1Rx8 L DDR3-1600 U ECC S26361-F3694-E613 second CPU if configured.
4GB (1x4GB) 2Rx8 L DDR3-1600 U ECC S26361-F3694-E614 For real memory speed (depending on memory type / population),
Registered Memory (RDIMM) no SDDC (chipkill) support please check the spreadsheet "Memory speed" below
- one DDR3 registered ECC mem. Module, 1.35V
No mix with any other types of memorymodules possible
Choose up to 6x for 2R per CPU
For performance reasons, we do not recommend
6x per
to configure more than 8 DIMMs per CPU
CPU, max. 4GB (1x4GB) 2Rx8 L DDR3-1600 R ECC S26361-F3695-E614
2/3 modules Registered Memory (RDIMM) with SDDC (chipkill) support
per channel - one DDR3 registered ECC mem. Module, 1.35V
1333MHz supported with up to 2DPC (6 modules/CPU)
Choose up to 6 order codes per CPU
4GB (1x4GB) 1Rx4 L DDR3-1333 R ECC S26361-F3696-E614 new due to supply
8GB (1x8GB) 2Rx4 L DDR3-1333 R ECC S26361-F3696-E615 new due to supply
2 modules
Registered Memory (RDIMM) with SDDC (chipkill) support
per channel - one DDR3 registered ECC mem. Module, 1.35V
1600MHz supported with up to 2DPC (8 modules/CPU)
at 1.5V Mix of memory modules is only possible within the same group
Choose up to 6 order codes per CPU
4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC S26361-F3697-E614
8GB (1x8GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E615
16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E616
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.35V
Choose up to 6 order codes per CPU
16GB (1x16GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E616
32GB (1x32GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E617
H
Effective Memory capacity / Rank Sparing Mode, 1 Channel populated
UDIMM
RDIMM
LRDIMM
2GB
2GB
4GB
8GB
2R
16GB
56GB
16GB
32GB
1DPC
12GB
24GB
2DPC
4GB
12GB
24GB
28GB
Fujitsu PRIMERGY Server 10 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
Memory Configuration PRIMERGY BX920 S3
Each CPU offers 6 Slots for DDR3 Memory Modules organised in 2 Banks and 3 Channels.
If you need more than 6 Slots you have to configure the 2nd CPU.
Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below).
There are 3 different kinds of DDR3 Memory Modules available: UDIMM / RDIMM and LRDIMM
UDIMM / RDIMM / LRDIMM offer different functionality. Mix of UDIMM / RDIMM / LRDIMM is not alloved.
If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V
Mode Configuration Application
SDDC (chipkill) support any no no yes detect multi-bit errors
Independant Channel 1, 2 or 3 Modules per Bank yes yes yes offers max. flexibility, upgradeability, capacity
Mode
use UDIMM modules for lowest cost
Mirrored Channel Mode *) 2 identical Modules / Bank no no yes offers maximum security
Performance Mode 3 identical Modules / Bank yes yes yes
offers maximum performance and capacity
Rank Sparing Mode *) min. 2 Ranks / Channel no no yes
balances security and capacity
*) For the delivery ex works the system will be prepared with dedicated BIOS setting.
Capacity Configuration UDIMM RDIMM LRDIMM Notes
Min. Memory per CPU
1 Module / CPU
1x2GB 1x4GB 1x 16GB
with one CPU
Max. Memory per CPU 4/6 Modules / CPU 6x4GB
6x16GB
6x 32GB with one CPU
Max. Memory per System 8/12 Modules / System 48GB 96GB 384GB if second CPU is configured
Memory-Speed:
Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU
The memory channel with the lowest speed defines the speed of all CPU channels in the system
Voltage setting (BIOS)
DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC
CPU with 1333MHz DDR3 Bus
CPU with 1066MHz DDR3 Bus
1R - Single Rank
2R - Dual Rank
4R - Quad Rank
1DPC = 1 DIMM per Channel
2DPC = 2 DIMM per Channel
3DPC = 3 DIMM per Channel
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I black sockets
Bank II blue sockets
Bank III
green sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1/2 up to 3 memory modules connected to Channel A - F on the 1st/2nd CPU
Bank II on CPU 1/2 up to 3 memory modules connected to Channel A - F on the 1st/2nd CPU
- See below and next page for a detailed descriptions of the memory configuration supported.
1
2
3
3
1
2
3
UDIMM
RDIMM
RDIMM
LRDIMM
x8
x8
x4
Mem. Speed provided
by CPU
Real maximum memory-bus speed depending on CPU type, memory configuration (DPC)
and voltage setting (BIOS)
UDIMM 1600MHz
RDIMM 1600MHz
LRDIMM 1333MHz
1.5V [default]
1.35V
1.5V [default]
1.35V
1.5V [default]
1.35V
CPU with 1600MHz DDR3 Bus
1333
1333
-
1066
1066
-
1
2
1
2
3
1
2
3
1
2
3
-
1066
1066
-
1333
1333
1066
1066
1600
1600
1333
1333
-
-
1333
1333
-
1066
-
-
1066
1066
-
1333
1333
-
1333
1333
-
1066
-
1066
1066
-
1066
1066
-
1066
-
-
-
1066
1066
-
1066
1066
-
1066
-
-
1600
-
1333
-
1333
1333
on special release
as soon as available
Fujitsu PRIMERGY Server 11 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
1. Independent Channel Mode
required
required if 2nd CPU is configured
Bank I Data
Data
Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data
Data
Data Data Data Data optional, any type
(blue sockets)
Independent Channel Mode allows all channels to be populated in any order
Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system
2. Mirrored Channel Mode
required
required if 2nd CPU is configured
Bank I Data Mirror -------- Data Mirror -------- optional, same type in Bank per CPU
(black sockets)
Bank II Data Mirror -------- Data Mirror -------- -------- not used
(blue sockets)
Mirrored Channel Mode requires identical modules on channel A / B (1st CPU) or channel D / E (2nd CPU)
50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory
If this mode is used, a multiple of 2 identical modules has to be ordered.
3. Performance Channel Mode
required
required if 2nd CPU is configured
Bank I Data
Data
Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data
Data
Data Data Data Data optional, any type
(blue sockets)
Performance Channel Mode requires identical modules on all channels of each Bank per CPU.
If this mode is used, a multiple of 3 identical modules has to be ordered.
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel A
Channel D
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8 Core)
Channel A
Channel D
Channel A
Channel D
Channel B
Channel C
Channel E
Channel C
Channel E
Channel F
Channel B
1st XEON CPU
(4/6/8 Core)
Channel F
Channel B
Channel C
Channel E
Channel F
2nd XEON CPU
(4/6/8) Core)
Fujitsu PRIMERGY Server 12 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
4. Rank Sparing Mode
required
required if 2nd CPU is configured
Bank I Spare
Spare
Spare Spare Spare Spare
optional, same type in Channel per CPU
(black sockets)
Bank II Data Data Data Data Data Data optional, any type
(blue sockets)
Bank I R1 Spare
Spare
Spare Spare Spare Spare
required
(black) R2 Data Data Data Data Data Data
required if 2nd CPU is configured
Bank II R1 Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data optional, same type in Channel per CPU
Bank I R1 Spare
Spare
Spare Spare Spare Spare
required
(black) R2 Data Data Data Data Data Data
R3 Data Data Data Data Data Data required if 2nd CPU is configured
R4 Data Data Data Data Data Data
optional, same type in Channel per CPU
Bank II R1 Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data optional, any type
R3 Data Data Data Data Data Data
R4 Data Data Data Data Data Data -------- not used
Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel.
The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above
"Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max.
available memory.
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel B
Channel A
Channel D
Channel B
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
2-Rank Memory modules (RDIMM)
Channel A
Channel D
Channel B
Channel C
Channel E
Channel F
4-Rank Memory modules (LRDIMM)
Channel F
Channel C
Channel E
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel A
Channel D
Channel E
Channel C
Channel F
1-Rank Memory modules (RDIMM)
Fujitsu PRIMERGY Server 13 of 14

System configurator and order-information guide
PRIMERGY BX920 S3 Status: 2013-12-30
Change Report
Date Order number Changes
2013-10-18 optional USB Comps no longer available
2013-07-18 Added comment about PCH Vmware limitation
2013-01-15 S26361-F3674-E1 Onboard Controller SAS upgrade - Speed corrected from 6GB/s to 3GB/s
2013-01-08
S26361-F5228-E*** New order number for 2.5" BC SAS 7.2K
2013-01-08
S26361-F5247-E130 New order number for SAS 10K (mix with BC-SATA supported, successor for *F5227*)
2012-10-16
hint SX910/910/960 only with 2nd CPU modified
2012-10-09
hint SX910/910/960 only with 2nd CPU
2012-10-02 changed USB info
2012-09-04
S26361-F3592-E532 as soon as available removed
2012-07-23
S26361-F5227-E1* New order for 2.5” 10K SAS HDD supporting mix with 2.5” BC-SATA HDD
2012-06-28
corrected text for 2 end Y-Cable
2012-06-12
S26361-F5225-E*00 New order for SATA SSD´s
2012-05-29
Added 1333 RDIMM
2012-05-01
First Release
Fujitsu PRIMERGY Server 14 of 14