Fujitsu PRIMERGY RX1330 M3 User manual

Operating Manual - English
FUJITSU Server PRIMERGY RX1330 M3
Operating Manual
March 2017

Copyright and Trademarks
Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected].
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright 2017 FUJITSU LIMITED
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any without the prior written permission of
Fujitsu.
Microsoft, Windows, Windows Server, and Hyper-V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

RX1330 M3 Operating Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.

Operating Manual RX1330 M3
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for Japan: About SATA HDDs
The SATA version of this server supports HDDs with SATA/BC-SATA storage
interfaces. Please note that the usage and operation conditions differ
depending on the type of HDD used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of HDD:
http://jp.fujitsu.com/platform/server/primergy/harddisk/

RX1330 M3 Operating Manual
Only for Japan:
IAlthough described in this manual, some sections do not apply to Japan.
These options and routines include:
– CSS (Customer Self Service)
– UFM (USB Flash Module)

Operating Manual RX1330 M3

RX1330 M3 Operating Manual
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.1 Concept and target groups for this manual . . . . . . . . . 11
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . 12
1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . 13
2 Functional overview . . . . . . . . . . . . . . . . . . . . . . 15
2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2 Server specification . . . . . . . . . . . . . . . . . . . . . . 23
3 Installation steps, overview . . . . . . . . . . . . . . . . . . 31
4 Important information . . . . . . . . . . . . . . . . . . . . . 33
4.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 33
4.2 ENERGY STAR . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.3 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.4 FCC Class A Compliance Statement . . . . . . . . . . . . . 43
4.5 Transporting the server . . . . . . . . . . . . . . . . . . . . 44
4.6 Notes on installing the server in the rack . . . . . . . . . . . 44
4.7 Environmental protection . . . . . . . . . . . . . . . . . . . 45
5 Hardware installation . . . . . . . . . . . . . . . . . . . . . 47
5.1 Unpacking the server . . . . . . . . . . . . . . . . . . . . . 48
5.2 Installing/removing the server in/from the rack . . . . . . . 48
5.3 Connecting devices to the server . . . . . . . . . . . . . . . 50
5.3.1 Connecting the monitor . . . . . . . . . . . . . . . . . . . . . 52

Operating Manual RX1330 M3
Contents
5.4 Connecting the server to the mains . . . . . . . . . . . . . . 52
5.4.1 Using cable ties (standard PSU) . . . . . . . . . . . . . . . . . 53
5.4.2 Using the cable clamps (hot-plug PSU) . . . . . . . . . . . . . . 54
5.5 Notes on connecting/disconnecting cables . . . . . . . . . . 55
6 Starting up and operation . . . . . . . . . . . . . . . . . . . . 57
6.1 Controls and indicators . . . . . . . . . . . . . . . . . . . . . 57
6.1.1 Server front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.1.1.1 Controls on the front panel . . . . . . . . . . . . . . . . . . 57
6.1.1.2 Indicators on the front panel . . . . . . . . . . . . . . . . . . 59
6.1.1.3 Indicators on the accessible drives/components . . . . . . . 62
6.1.2 Server rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.1.2.1 Indicators on the I/O panel . . . . . . . . . . . . . . . . . . 64
6.1.2.2 Indicator on hot-plug PSUs . . . . . . . . . . . . . . . . . . 68
6.1.2.3 Indicator on Fujitsu battery unit (FJBU) . . . . . . . . . . . . 69
6.2 ID card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
6.3 Switching the server on and off . . . . . . . . . . . . . . . . 71
6.4 Configuring the server . . . . . . . . . . . . . . . . . . . . . 73
6.4.1 Configuring the onboard SATA controller . . . . . . . . . . . . . 73
6.4.2 Configuring the SAS/SATA RAID controller . . . . . . . . . . . . 74
6.4.3 Configuring the server and installing the operating system
with the ServerView Installation Manager . . . . . . . . . . . . . 74
6.4.4 Configuring the server and installing the operating system
without the ServerView Installation Manager . . . . . . . . . . . 75
6.5 Cleaning the server . . . . . . . . . . . . . . . . . . . . . . . 76
7 Property and data protection . . . . . . . . . . . . . . . . . . 77
7.1 BIOS Setup security functions . . . . . . . . . . . . . . . . . 77
8 Troubleshooting and tips . . . . . . . . . . . . . . . . . . . . 79
8.1 Power-on indicator remains unlit . . . . . . . . . . . . . . . . 79
8.2 Server switches itself off . . . . . . . . . . . . . . . . . . . . 80
8.3 Screen remains blank . . . . . . . . . . . . . . . . . . . . . . 80

RX1330 M3 Operating Manual
Contents
8.4 Flickering stripes on monitor screen . . . . . . . . . . . . . 81
8.5 No screen display or display drifts . . . . . . . . . . . . . . 81
8.6 No mouse pointer displayed on screen . . . . . . . . . . . . 81
8.7 Incorrect date and time . . . . . . . . . . . . . . . . . . . . 82
8.8 Drives reported as “dead” when starting system . . . . . . 82
8.9 Added drive reported as defective . . . . . . . . . . . . . . 82
8.10 Error message on screen . . . . . . . . . . . . . . . . . . . 83
8.11 Expansion cards or onboard devices not recognized . . . . 83
8.12 Temperature warning . . . . . . . . . . . . . . . . . . . . . . 83
8.13 No effect of keyboard or mouse . . . . . . . . . . . . . . . . 83
8.14 ODD cannot read data . . . . . . . . . . . . . . . . . . . . . 84

Operating Manual RX1330 M3
Contents

RX1330 M3 Operating Manual 11
1 Introduction
The PRIMERGY RX1330 M3 server is an Intel®-based server for small and
medium-sized networks and can be used in the rack systems made by Fujitsu
and in current standard rack systems made by various other manufacturers.
Thanks to its highly developed hardware and software components, the
PRIMERGY RX1330 M3 server offers a high level of data security and
availability. These include the Server Management ServerView Suite, Prefailure
Detection and Analysis (PDA) and Automatic Server Reconfiguration and
Restart (ASR&R).
Security functions in the BIOS Setup and on the system board protect the data
on the server against manipulation. Additional security is provided by the
lockable rack door.
The server occupies 1 height unit in the rack.
1.1 Concept and target groups for this manual
This operating manual describes how to install, set up and operate your server.
This operating manual is intended for those responsible for installing the
hardware and ensuring that the system runs smoothly. It contains all the
information you need to put your PRIMERGY RX1330 M3 into operation.
To understand the various expansion options, you will need to be familiar with
the fields of hardware and data transmission and you will require a basic
knowledge of the underlying operating system.

12 Operating Manual RX1330 M3
Introduction
1.2 Documentation overview
More information on your PRIMERGY RX1330 M3 can be found in the following
documents:
– "Quick Start Hardware - FUJITSU Server PRIMERGY RX1330 M3"
– "ServerView Quick Start Guide"
– "Safety Notes and Regulations" manual
"安全上のご注意 " for Japan
– "Warranty" manual
"保証書 " for Japan
– "ServerView Suite Local Service Concept - LSC" manual
– "Returning used devices" manual and "Service Desk" leaflet
"サポー ト ＆サー ビ ス " for Japan
– "FUJITSU Server PRIMERGY RX1330 M3 Upgrade and Maintenance
Manual"
– "D3375 BIOS Setup Utility for FUJITSU Server PRIMERGY RX1330 M3
Reference Manual"
IAll documentation on PRIMERGY hardware and ServerView software is
available online from the Fujitsu manuals server at:
http://manuals.ts.fujitsu.com
For Japan:
http://www.fujitsu.com/jp/products/computing/servers/primergy/manual/
The complete PRIMERGY documentation set can also be downloaded
as a DVD ISO image at:
ftp://ftp.ts.fujitsu.com/images/serverview/manuals
For Japan:
http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/

RX1330 M3 Operating Manual 13
Introduction
Further sources of information:
– ServerView Suite Glossary
– Manual for the monitor
– Documentation for the boards and drives
– Operating system documentation
– Information files in your operating system
1.3 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

14 Operating Manual RX1330 M3
Introduction

RX1330 M3 Operating Manual 15
2 Functional overview
This section provides information on the features and technical data of the
PRIMERGY RX1330 M3 server.
2.1 Features
Intel®Xeon®, Pentium®, or Core i3 CPU
The server has an Intel®Xeon®, Pentium®, or Core i3 CPU for high-speed data
processing.
Customer Self Service (CSS)
The PRIMERGY Customer Self Service (CSS) concept enables you to identify
and replace the affected component yourself in the case of certain error
scenarios.
In the CSS concept, you can replace the following components yourself in the
event of an error:
– Hot-plug HDD/SSD modules
– Hot-plug PSUs
– Memory modules
– System fans
– Expansion cards
For information on replacing these components, see the "FUJITSU Server
PRIMERGY RX1330 M3 Upgrade and Maintenance Manual".
CSS indicators on the control panel and on the back of the PRIMERGY server
provide you with information if a CSS event arises.
In addition, CSS errors are displayed in the ServerView Operations Manager,
the server management software from Fujitsu.
In the event of errors, the ServerView Operations Manager refers you directly
to the affected component and its order information in the Illustrated Spares
catalog of the server in question. (This feature is not available for Japan.)

16 Operating Manual RX1330 M3
Functional overview
IFurther information on the CSS concept is provided in the "PRIMERGY
ServerView Suite Local Service Concept - LSC" manual on the Fujitsu
manuals server.
For the latest information on optional products provided for the
RX1330 M3 see the configurator of the server:
http://ts.fujitsu.com/products/standard_servers/index.html
For Japan:
http://www.fujitsu.com/jp/products/computing/servers/primergy/
System board
The features of the system board are described in the "FUJITSU Server
PRIMERGY RX1330 M3 Upgrade and Maintenance Manual" for the hardware
and in the "D3375 BIOS Setup Utility for FUJITSU Server PRIMERGY
RX1330 M3 Reference Manual" for the firmware.
Trusted Platform Module (TPM)
A Trusted Platform Module (TPM) for safer storage of keys can be implemented
as an option. This module enables programs from third party manufacturers to
store key information (e.g. drive encryption using Windows Bitlocker Drive
Encryption).
The TPM is activated via the BIOS system (for more information, refer to the
“D3375 BIOS Setup Utility for FUJITSU Server PRIMERGY RX1330 M3
Reference Manual").
VCAUTION!
– When using the TPM, note the program descriptions provided by the
third party manufacturers.
– You must also create a backup of the TPM content. To do this, follow
the third party manufacturer's instructions. Without this backup, if the
TPM or the system board is faulty you will not be able to access your
data.
– If a failure occurs, please inform your service about the TPM
activation before it takes any action, and be prepared to provide them
with your backup copies of the TPM content.

RX1330 M3 Operating Manual 17
Functional overview
Hard disk drives (HDDs)
The server is shipped with one of the following drive cages:
– For up to four 3.5-inch SAS/SATA HDD modules:
Up to four 3.5-inch SAS/SATA HDD modules can be used in the drive cage.
Each HDD module can accommodate an SAS/SATA HDD with a maximum
height of 1 inch. The module is connected to the SAS/SATA backplane
wirelessly. This allows HDD modules to be plugged in or pulled out easily.
Hybrid configurations of SAS and SATA HDD modules within one drive cage
are not supported.
– For up to four, eight or ten 2.5-inch SAS/SATA HDD modules or 2.5-inch
SATA SSD modules:
Each module can accommodate SAS/SATA HDD or an SATA SSD with a
2.5-inch format. The HDD/SSD modules are connected to the SAS/SATA
backplane wirelessly. This allows modules to be plugged in or pulled out
easily.
IUp to ten SAS/SATA drives are controlled by the SAS/SATA RAID
controller already installed.
IConfigurations with Eco SATA can only be mixed with BC SATA HDD
type. SAS and BC SATA drives with the same size can be mixed, but
not used in the same logical RAID volume.
Hybrid configurations of SATA HDD and SATA SSD modules are supported.
If the server has the corresponding RAID configuration, the HDD/SSD modules
can also be replaced during operation.
Onboard SATA controller
A SATA controller is integrated on the system board; up to four SATA HDDs can
be connected to the controller. The LSI Embedded MegaRAID software (SATA
Software RAID) supports RAID levels 0, 1 and 10.
For more information on configuring the controller, see section "Configuring the
onboard SATA controller" on page 73.

18 Operating Manual RX1330 M3
Functional overview
SAS/SATA RAID controller
The server is available with the following SAS/SATA RAID controllers for
operating the internal SAS/SATA HDDs:
– Modular Host Bus Adapter with "Integrated RAID" (IR). RAID levels 0 and 1
are supported for internal HDD configurations.
– Modular RAID 0/1 controller with "MegaRAID functionality" (integrated
MegaRAID).
RAID levels 0, 1, 10, 5 and 50 are supported for internal HDD configurations.
– Modular RAID 5/6 controller with "MegaRAID functionality" (MegaRAID).
RAID levels 0, 1, 10, 5, 50, 6 and 60 are supported for internal HDD
configurations. As an option, a flash backup unit (FBU) can save the
memory content even if the power fails. Cache memory size of 1GB or 2GB
are available.
IFor more information on configuring the controller, see section
"Configuring the SAS/SATA RAID controller" on page 74.
Further information on SAS/SATA RAID controllers is provided in the
"Modular RAID Controller Installation Guide" (on the Fujitsu manuals
server under x86 Servers - Expansion Cards - Storage Adapters - LSI SAS /
SCSI RAID Controllers).
Further information on other SAS/SATA RAID controllers (e.g. for
operating external SAS/SATA HDDs or tape drives) is available on the
Fujitsu manuals server under x86 Servers - Expansion Cards - Storage
Adapters - LSI SAS / SCSI RAID Controllers.
Optical disk drive (ODD)
An installation slot for an ultra slim ODD (optional) is available.
IFor the variant with 10 HDDs there is no slot available for an ultra slim
ODD.
Power supply unit (PSU)
In its basic configuration the server has a standard PSU or a hot-plug PSU that
adjusts automatically to any mains voltage in the range 100 V - 240 V. Besides
the hot-plug PSU, a second hot-plug PSU can be installed optionally to serve
as a redundant Power Supply. If one PSU fails, the second PSU in the
redundant configuration ensures operation can continue uninterrupted.

RX1330 M3 Operating Manual 19
Functional overview
Fujitsu battery unit (FJBU)
FJBU behaves as a modular UPS in the server. When power fail happened, the
server can operate by FJBU for a while. FJBU supports hot-plugging, and can
be replaced during operation.
You can download the management software (FJBU management software) for
the following OS:
– Windows Server 2016
– Windows Server 2012 R2, Windows Server 2012
– Windows Server 2008 R2 SP1, Windows Server 2008 SP2
IFJBU management software is not available in Red Hat Enterprise Linux
environment. Please use the IPMI function at Linux environment.
Advanced Thermal Design
The Advanced Thermal Design option allows you to operate the system with a
wider temperature range of 5 °C to 40 °C, depending on your system and
configuration.
VCAUTION
In a system that is configured with Advanced Thermal Design, only
certain components which support the respectively increased higher
operating temperature range may be installed and used. For applicable
restrictions, please refer to the official configurator tool.
High level of availability and data security
When memory data is accessed, 1-bit errors are identified in the main memory
and automatically corrected with the error correcting code (ECC) method.
ASR&R (Automatic Server Reconfiguration and Restart) restarts the system in
the event of an error and automatically "hides" the defective system
components.
The PDA (Prefailure Detection and Analysis) technology from Fujitsu analyzes
and monitors all components that are critical for system reliability.
A RAID controller supports different RAID levels and increase the availability
and data security of the system.
The hot-plug HDD modules provide additional availability.
This option can only be ordered from the manufacturer and is
indicated by the respective logo on the identification rating
plate.

20 Operating Manual RX1330 M3
Functional overview
iRMC S4 with integrated management LAN connector
The iRMC S4 (integrated Remote Management Controller) is a Baseboard
Management Controller (BMC) with integrated management LAN connector
and expanded functionality that was previously only available with additional
plug-in cards. In this way, the iRMC S4 enables complete control of PRIMERGY
servers, regardless of system status, and thus particularly the control of
PRIMERGY servers that are in the "out-of-band" system status.
Major functions supported by the iRMC S4 include the following:
●Browser access via iRMC S4´s own Web server
●Secure communication (SSH, SSL)
●Power Management for the managed server (depending on its system
status)
●Power Consumption Management
●Connecting virtual drives as remote storage
●Text-based and graphic console bypass (Advanced Video Redirection)
●Remote Storage
●Command Line Interface (CLI)
●Simple, interactive or script-based iRMC S4configuration
●Customer Self Service (CSS)
●iRMC S4´s own user management
●Multi-computer, global iRMC S4 user administration using an LDAP
Directory Service
●Automatic network configuration via DNS / DHCP
●Power supply of the iRMC S4 via the system standby supply
●Full-coverage alarm management
●System Event Log (SEL) reading and processing
●IPMI support
●CIM / WS-MAN support
●Internal Event Log for user login / logout auditing