Fujitsu PRIMERGY S60 User manual

Primergy
PRIMERGY S60
Storage Subsystem
Xenia Fierley
Fujitsu Siemens Computers GmbH cognitas PS
81730 München
e-mail: email:[email protected]
Tel.: [phone]
Fax: 0 700 / 372 00000
U41221-J-Z156-1-74
Sprachen: En
Edition September 2001

This manual is printed on
paper treated with
chlorine-free bleach.
Comments…Suggestions…Corrections…
The User Documentation Department would like to know
your opinion on this manual. Your feedback helps us to
optimize our documentation to suit your individual needs.
Fax forms for sending us your comments are included at the
back of the manual.
There you will also find the addresses of the relevant User
Documentation Department
Copyright and Trademarks
Copyright © 2001 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
This manual was produced by
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de

German
English

U41221-J-Z156-1-74
Contents
1Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Target Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Notation Conventions . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 Structure of the Manual . . . . . . . . . . . . . . . . . . . . . . 3
1.4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Notes on Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Electrostatic Sensitive Device Label . . . . . . . . . . . . . . . . 9
2.3 CE certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 RFI Suppression . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.5 FCC notices (Federal Communications Commission) . . . . . . 10
2.6 Notes on the Rack Model . . . . . . . . . . . . . . . . . . . . 11
2.7 Notes on Transportation . . . . . . . . . . . . . . . . . . . . . 11
2.8 Environmental Protection . . . . . . . . . . . . . . . . . . . . 12
3 Operating and Indicator Elements . . . . . . . . . . . . . . 15
3.1 The Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1.1 Meaning of the S60 Operating Status LEDs . . . . . . . . . . . 16
3.1.2 The Control LEDs for the Hard Disk Drives . . . . . . . . . . . 18
3.2 The Rear Side . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.1 FFx-RAID Controller Module LEDs . . . . . . . . . . . . . . . 20
3.2.2 Power Supply Unit LEDs . . . . . . . . . . . . . . . . . . . . . 21
3.2.3 Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3 Fan LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4 Floorstand Model . . . . . . . . . . . . . . . . . . . . . . . . 25
4.1 Open the Housing . . . . . . . . . . . . . . . . . . . . . . . . 25
4.1.1 Removing and Mounting the door . . . . . . . . . . . . . . . . 25
4.1.2 Removing/Mounting the left Side Cover . . . . . . . . . . . . . 26
5PowerSupply. . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.1 Power Supply Units . . . . . . . . . . . . . . . . . . . . . . . 29
5.1.1 Replacing the Power Supply Unit . . . . . . . . . . . . . . . . 30
6 Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.1 Installing/Removing the Fan Module . . . . . . . . . . . . . . . 34

U41221-J-Z156-1-74
Contents
7 FC Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . 37
7.1 Handling Hard Disk Drives/HDD Modules . . . . . . . . . . . . 37
7.2 Installing/Removing HDD/Dummy Module . . . . . . . . . . . . 38
7.3 Hot Swap for FC HDD Modules . . . . . . . . . . . . . . . . . . 42
7.4 Identification Marks and Loop Addresses . . . . . . . . . . . . . 43
8 Plug-in Board Modules . . . . . . . . . . . . . . . . . . . . . 45
8.1 The FFx-RAID Controller Module . . . . . . . . . . . . . . . . . 45
8.1.1 Indicators and Connectors . . . . . . . . . . . . . . . . . . . . 46
8.1.2 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
8.1.3 Installing/removing the FFx-RAID controller module . . . . . . . 52
8.1.4 Adding a Second FFx-RAID Controller Module . . . . . . . . . . 54
8.1.5 The FFx-BBU (Battery Backup Unit) Module . . . . . . . . . . . 55
9 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.1 Fibre Channel (FC) Connection . . . . . . . . . . . . . . . . . . 58
9.2 Mains Connection . . . . . . . . . . . . . . . . . . . . . . . . . 58
9.3 Mains Connection with Phase Redundancy . . . . . . . . . . . 59
9.4 Power connection via UPS . . . . . . . . . . . . . . . . . . . . 60
10 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
10.1 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . 61
10.2 Unpacking the Storage Subsystem . . . . . . . . . . . . . . . . 62
10.3 Setting Up the Floorstand Model . . . . . . . . . . . . . . . . . 62
10.4 Mounting the Rack Model . . . . . . . . . . . . . . . . . . . . 63
10.4.1 Preparing the Slide Rails . . . . . . . . . . . . . . . . . . . . . 64
10.4.2 Mounting Slide Rails . . . . . . . . . . . . . . . . . . . . . . . 65
10.4.3 Mounting the Subsystem . . . . . . . . . . . . . . . . . . . . . 65
10.4.4 Routing the Cables . . . . . . . . . . . . . . . . . . . . . . . . 66
10.5 Connecting and Disconnecting Cables . . . . . . . . . . . . . . 68
10.6 Switching the Storage Subsystem ON/OFF . . . . . . . . . . . 69
11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 71
11.1 Problem Solutions and Tips . . . . . . . . . . . . . . . . . . . . 71
11.1.1 Power Supply Status Indicator (Front) . . . . . . . . . . . . . . 71
11.1.1.1 Power supply status indicator remains dark . . . . . . . . . . . 71
11.1.1.2 Power supply status indicator lights yellow . . . . . . . . . . . . 72
11.1.1.3 Power supply status indicator lights orange . . . . . . . . . . . 72
11.1.2 Cooling Status . . . . . . . . . . . . . . . . . . . . . . . . . . 73
11.1.2.1 Cooling status LED lights yellow . . . . . . . . . . . . . . . . . 73
11.1.2.2 Cooling status LED lights orange . . . . . . . . . . . . . . . . . 73

U41221-J-Z156-1-74
Contents
11.1.3 Server Management Status . . . . . . . . . . . . . . . . . . . 74
11.1.3.1 Server Management Status LED lights permanently . . . . . . 74
11.1.4 Storage Subsystem Switches OFF . . . . . . . . . . . . . . . 75
11.1.5 System will not boot after Installation of New HDD Modules . . 75
11.1.6 HDD READY Indicator does not light up . . . . . . . . . . . . . 75
11.1.7 Hard Disk Drives“ dead” on System Start . . . . . . . . . . . . 76
11.1.8 Controller reports Added Hard Disk Drive as defective . . . . . 76
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

U41221-J-Z156-1-74 1
1 Introduction
The functionality, mechanics and design of the PRIMERGY S60 storage
subsystem are optimally adapted to the PRIMERGY Nxxx server compute-
nodes. It can be used as rack or as floorstand model. In the 19-inch rack, the
S60 subsystem occupies three height units.
The PRIMERGY S60 storage subsystem use the fiber-channel technology and
can accommodate up to fourteen 1-inch hard disk drives.
The use of fiber-channel technology ensures high transmission speeds over
long distances, using a very uncomplicated infrastructure.
Components such as fans, power supply units, hard disk drives and FFx-RAID
controller modules (dual controller configuration only) can be replaced with the
system running. Redundancy is provided for central components, offering a
high degree of data security and reliability.
Server Management/ServerView
For the first step the server management for the PRIMERGY S60 storage
subsystem will be ensured by SES (SCSI Enclosure Service).
A optional Remote Service Board (RSB) with more functions can be installed.
In this case remote diagnosis is available to the customer or service provider for
analysis, remote system configuration and a remote restart - even if the
operating system or the hardware fails.
The RSB-module is board which includes a completely independent system. It
has a separate operating system with web server and SNMP agents, and can
be driven by an external power supply.
The board is installed in the storage subsystem and connected to the HDD
backplane.
Further informations is provided in the documentation for the Remote Service
Board (see “Related publications” on page 81).
ServerView and the related agents are set up within the group of servers and
storage subsystems being monitored. The received information are evaluated
by ServerView and processed for display or forwarding to the administrator
(manager).

2 U41221-J-Z156-1-74
Target Group Introduction
IWhen installing PRIMERGY S60 storage subsystems in connection with
ServerView please install the ServerStart CD version 4.06 or higher on
each of the connected servers.
See ServerView documentation for notes concerning installing and update (see
also “Related publications” on page 81).
1.1 Target Group
The operating instructions are intended for the person responsible for installing
the hardware and correctly operating the system. The operating manual contain
all the descriptions which are of importance for commissioning your
PRIMERGY S60 storage subsystem in so far as they do not form part of the
publication of your server system.
To understand the different expansion options it is necessary to have a
knowledge of hardware and data transmission, as well as basic knowledge of
the operating system used.
1.2 Notation Conventions
Italics identifies commands and entries in flow text
Bold highlights text
“Quotation marks” indicates references to other chapters or manuals
Êidentifies an operation that you have to perform.
Iindicates additional information, notes and tips
VCAUTION! indicates warnings, which, if ignored, will endanger
your health, the operability of your server or the
security of your data

U41221-J-Z156-1-74 3
Introduction Structure of the Manual
1.3 Structure of the Manual
The PRIMERGY S60 storage subsystem manual describes how to install and
configure the subsystem and perform expansions or upgrades.
You will find further information (see also entries in the chapter “Related publi-
cations” on page 81):
●in the “Safety, Warranty and Ergonomics” manual
●in the documentation on the PRIMERGY server
This manual consists of the following chapters:
●Important notes
This chapter contains instructions on the safe operation of your storage
subsystem as well as information about environmental protection.
●Operating and indicator elements
This chapter gives a detailed description of the operating panel and the
connecting elements on the rear panel of the storage subsystem.
●Floorstand model
This part of the manual describes how opening and closing the floorstand
model housing.
●Power supply
This part of the manual describes the power supply units and their power
supply. Fitting and removing power supply units is also described in detail.
●Fan module
This part of the manual describes the fitting and removal of the fan module.
●FC drives
This chapter describes in detail how the hot swappable drives must be dealt
with.
●Plug-in board modules
This chapter describes the FFx-RAID controller and its mounting and
removal.
●Connections
This chapter describes the FC and the mains connection.
The possibilities of supplying the storage subsystem with mains voltage are
also described.

4 U41221-J-Z156-1-74
Technical Data Introduction
●Configurations
This part of the manual gives configuration examples.
●Installation
The activities needed to install and commission the storage subsystem are
described.
●Troubleshooting
This chapter contains advice on solving problems that occur on commis-
sioning or during the operation of the storage subsystem.
1.4 Technical Data
Electrical Characteristics
Rated voltage 100 V - 240 V
Tolerance of the rated voltage +6 % / -10 %
Rated frequency 50 Hz / 60 Hz
Rated current max. 1.3 A at 240 V
max. 3.1 A at 100 V
Power consumption
Active power (= heat transfer) max. 305 W
Apparent power max. 310 VA
Power factor (PF) 0.95-0.99
Dimensions and
Weight
Floorstand model Rack model
Height 481mm 133 mm
Width 200 mm without legs
280 mm with legs
483 mm
Depth 692 mm 646 mm
Weight max. 32 kg max. 30 kg

U41221-J-Z156-1-74 5
Introduction Technical Data
Environmental Conditions (according to DIN EN 60721-3-x)
Climate/operation (class 3K2):
Temperature 15 °C to 35°C
Relative humidity 5% to 85%
altitude (NN) max. 3048 m (10000 ft.)
Climate/transport (class 2K2):
Temperature -25°C to 60°C
Relative humidity 15% to 98%
altitude (NN) max. 15240 m (50000 ft.)
Mechanical environmental conditions
Operation Class 3M2
Transport Class 2M1
Standards Complied With
Product safety and ergonomics IEC 60950 (DIN EN 60950), UL 1950,
CSA 950, ZH1/618
Electromagnetic compatibility
Emitted interference EN 55022, class B; FCC part 15, class A
Noise immunity EN 50082-1
CE label Low voltage guideline
LVD 73/23/EEC
EMC guideline 89/339/EWG
Approval certification GS, CSA NRTL/C, CB certificate
Noise Development (ISO 9296) Operation Idle
Sound level (LWAd) max. 7.0 B max. 6.2 B
Workstation-related
sound pressure level (LpAm)
max. 56 dB(A) max. 46 dB(A)
Maintenance Areas and Ventilation Distances
Floorstand model Rear 400 mm, left 1200 mm *
Rack model Specified by the 19“ rack
* The area on the left need not always be kept open. However, it must be
possible to clear it without too much effort.

U41221-J-Z156-1-74 7
2 Important Notes
2.1 Notes on Safety
In this section you will find information that you must note when using the
storage subsystem.
This device complies with the relevant safety standards for IT equipment,
including electronic office machines, intended for use in the office environment.
IYou will also find the following safety instructions in the manual entitled
“Safety, Warranty and Ergonomics“ which also includes other notes on
guarantee and ergonomics. Also pay attention to the notes in the manual
of the connected PRIMERGY system.
If you have any questions relating to setting up and operating your system in the
environment where you intend to use it, please consult our service organization.
VCAUTION!
●The actions described in these instructions should only be performed
by technicians, service personnel or technical specialists. Equipment
repairs should only be performed by qualified staff. Any failure to
observe the guidelines in this manual could expose the user to risks
(electric shock, fire hazards) and could also damage the equipment.
Note that any unauthorized opening of the device will result in the
invalidation of the warranty and exclusion from all liability.
●Transport the device in its original packaging or in other suitable
packaging which will protect it against shock or impact.
●Read the notes on environmental conditions in section “Technical
Data” on page 4 before setting up and operating the device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.

8 U41221-J-Z156-1-74
Notes on Safety Important Notes
VCAUTION!
●Check that the rated voltage specified on the device's ID plate is the
same as the local line voltage.
●The device must only be connected to a properly grounded wall outlet
(the device is fitted with a tested and approved power cable).
●Make sure that the protective grounded outlet of the building’s wiring
system is freely accessible.
●Switching off the device does not cut off the supply of power. To do
this you must remove the power plugs.
●Before opening the unit, switch off the device and then pull out the
power plugs.
●Route the cables in such a way that they do not form a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting up a device, refer to the relevant
notes in this manual.
●Never connect or disconnect data transmission lines during a storm
(lightning hazard).
●Systems which comprise a number of cabinets must use a separate
fused socket for each cabinet.
●The system unit and the directly connected external storage
subsystems should be connected to the same power supply
distributor. Otherwise you run the risk of losing data if, for example,
the central processing unit is still running but the storage subsystem
has failed during a power failure.
●Make sure that no objects (such as bracelets or paper clips) fall into
or liquids spill into the device (risk of electric shock or short circuit).
●In emergencies (e.g. damage to housings, power cords or controls or
ingress of liquids or foreign bodies), immediately power down the
device, pull out the power plugs and notify your service department.
●Note that proper operation of the system (in accordance with IEC
60950/DIN EN 60950) is guaranteed only if slot covers are installed
on all vacant slots and/or dummies on all vacant bays and the
housing cover is fitted (cooling, fire protection, RFI suppression).

U41221-J-Z156-1-74 9
Important Notes Electrostatic Sensitive Device Label
2.2 Electrostatic Sensitive Device Label
Electrostatic-sensitive components may be identified by the following sticker:
Figure 1: Electrostatic Sensitive Device (ESD) sticker
You must follow the instructions below when handling modules containing
electrostatic-sensitive components
ÊDischarge static electricity from your body (for example by touching a
grounded metal object) before handling modules containing electrostatic-
sensitive components.
ÊThe equipment and tools you use must be free of static charge.
ÊRemove the power plug before installing or removing modules containing
electrostatic-sensitive components.
ÊOnly hold modules containing electrostatic-sensitive components by their
edges.
ÊDo not touch any of the pins or track conductors on a module containing
electrostatic-sensitive components.
ÊUse a grounding strap designed for the purpose, to connect you to the
system unit as you install the modules.
ÊPlace all components on a static-safe base.
IAn exhaustive description of the handling of modules containing electro-
static-sensitive components can be found in “Guidelines on handling
electrostatic sensitive devices and modules (ESD)” or “ITS Circular
4/95”.

10 U41221-J-Z156-1-74
CE certificate Important Notes
2.3 CE certificate
2.4 RFI Suppression
All other equipment which is connected to this product must also have radio
noise suppression in accordance with EC Guideline 89/336/EWG.
Products which meet this requirement are accompanied by a certificate to that
effect issued by the manufacturer and/or bear the CE mark. Products which do
not meet this requirement may be operated only with the special permission of
the BZT (Bundesamt für Zulassungen in der Telekommunikation).
2.5 FCC notices (Federal Communications
Commission)
Class A digital device
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful inter-
ference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
The shipped version of this device complies with the requirements
of the EEC directives 89/336/EEC “Electromagnetic compatibility”
and 73/23/EEC “Low voltage directive”. The device therefore
qualifies for the CE certificate (CE=Communauté Européenne).

U41221-J-Z156-1-74 11
Important Notes Notes on the Rack Model
2.6 Notes on the Rack Model
●For safety reasons, at least two people are required to install the rack model
because of its weight and size.
●When connecting and disconnecting cables, observe the notes in the
documentation for your PRIMERGY system and the comments in the
“Important notes” chapter in the technical manual supplied with the rack.
●Ensure that the anti-tilt bracket is correctly mounted when you set up the
rack.
●For safety reasons, no more than one unit may be withdrawn from the rack
at any one time during installation and maintenance work.
●If more than one unit is withdrawn from the rack at any one time, there is a
danger that the rack will tilt forward.
●The connection of the rack to the mains voltage must be installed by an
authorized specialist (electrician).
2.7 Notes on Transportation
ITransport the storage subsystem in its original packaging or in other
suitable packaging which will protect it against shock or impact.
Do not unpack it until all transport maneuvers are completed.
If you need to lift or transport the storage subsystem, ask someone to
help you.

12 U41221-J-Z156-1-74
Environmental Protection Important Notes
2.8 Environmental Protection
Environmentally friendly product design and development
This product has been designed in accordance with the Fujitsu Siemens
Computers standard for “environmentally friendly product design and devel-
opment”.
This means that the designers have taken into account important criteria such
as durability, selection of materials and coding, emissions, packaging, the ease
with which the product can be dismantled and the extent to which it can be
recycled.
This saves resources and thus reduces the harm done to the environment.
Notes on saving energy
Devices that do not have to be on permanently should not be switched on until
they need to be used and should be switched off during long breaks and on
completion of work
Notes on packaging
We recommend that you do not throw away the original packaging in case you
need it later for transportation. If possible, devices should be transported in their
original packaging.
Notes on dealing with consumables
Please dispose of batteries in accordance with local regulations.
Notes on labeling plastic housing parts
Please avoid attaching your own labels to plastic housing parts wherever
possible, since this makes it difficult to recycle them.