Fujitsu PRIMERGY SX980 S1 Owner's manual

Service Supplement - English
PRIMERGY SX980 S1 / SX980 S2
Storage Blade
Service Supplement
Edition October 2012

Copyright and Trademarks
Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected]su.com.
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright © 2012 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

SX980 S1 / SX980 S2 Service Supplement
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.

Service Supplement SX980 S1 / SX980 S2
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market:
About SATA hard disk drives
The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://primeserver.fujitsu.com/primergy/harddisk/

SX980 S1 / SX980 S2 Service Supplement
Only for the Japanese market:
IAlthough described in this manual, some sections do not apply to the
Japanese market. These options and routines include:
– CSS (Customer Self Service)

Service Supplement SX980 S1 / SX980 S2

SX980 S1 / SX980 S2 Service Supplement
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 9
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 9
1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . 11
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4 Replacement routines . . . . . . . . . . . . . . . . . . . . . 17
4.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1.1 Removing the storage blade from the system unit . . . . . . . 17
4.2 Replacing the complete storage blade . . . . . . . . . . . . 18
5 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1 PRIMERGY SX980 S1 . . . . . . . . . . . . . . . . . . . . . 19
5.1.1 SX980 S1 storage blade as spare part . . . . . . . . . . . . . 19
5.1.2 SX980 S1 storage blade cable plan . . . . . . . . . . . . . . . 20
5.2 PRIMERGY SX980 S2 . . . . . . . . . . . . . . . . . . . . . 21
5.2.1 SX980 S2 storage blade as spare part . . . . . . . . . . . . . 21
5.2.2 SX980 S2 storage blade cable plan . . . . . . . . . . . . . . . 22
5.3 Installing drive modules . . . . . . . . . . . . . . . . . . . . 23

Service Supplement SX980 S1 / SX980 S2
Contents

SX980 S1 / SX980 S2 Service Supplement 9
1 Introduction
The PRIMERGY SX980 S1 / SX980 S2 storage blade is used as a storage
subsystem for the PRIMERGY BX400 S1 and BX900 S1 / BX900 S2 system
unit.
The storage blade comes with 10 bays for 2.5-inch SAS HDD/SSD modules and
occupies two bays in the system unit. Up to three SX980 S1 / SX980 S2 storage
blades can be installed per BX400 S1 system unit. Up to six SX980 S1 /
SX980 S2 storage blades can be installed per BX900 S1 / BX900 S2 system
unit.
1.1 Concept and target groups
This Service Supplement completes the information given in the Operating
Manual.
The activities described in this manual may only be performed by service
personnel.
1.2 Documentation overview
Service DVD PRIMERGY
Service partners of Fujitsu Technology Solutions can order a PRIMERGY
Service DVD. On the DVD the following manuals are available in pdf format:
– "Safety Notes and Regulations" manual
– "PRIMERGY SX980 S1 / SX980 S2 Storage Blade Operating Manual"
– "PRIMERGY SX980 S1 / SX980 S2 Storage Blade Service Supplement"

10 Service Supplement SX980 S1 / SX980 S2
Introduction
Information/procedure Manual
Detailed safety notes Safety notes and
regulations
Features and technical data of the storage blade Operating Manual
Installation and operation, among other things:
– Installation in the system units
– Starting up
– Operation
Installation/removal of components:
– Hot-plug hard disk drives and solid state drives
Replacement routines:
– SX980 S1 / SX980 S2 storage blade complete
(with cables)
Service Supplement
Board layouts and cable plan
Table 1: Overview of the documentation for PRIMERGY SX980 S1 / SX980 S2 storage blade

SX980 S1 / SX980 S2 Service Supplement 11
Introduction
1.3 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

12 Service Supplement SX980 S1 / SX980 S2
Introduction

SX980 S1 / SX980 S2 Service Supplement 13
2 Procedure
VCAUTION!
The actions described in these instructions should only be performed by
service personnel.
ÊFirst of all please familiarize yourself with the safety instructions in the
chapter "Safety notes" on page 15.
ÊEnsure that all required manuals (see Service DVD) are available, print out
the PDF files if necessary. You will definitely need the Operating Manual for
the system unit and the server blades.
ÊSwitch off the related server blade(s) and pull the storage blade out of the
slot as described in section "Removing the storage blade from the system
unit" on page 17.
ÊPush the storage blade in the slot. (These procedures are described in the
Operating Manual.)
ÊPut the storage blade into operation. (These procedures are described in the
Operating Manual.)

14 Service Supplement SX980 S1 / SX980 S2
Procedure

SX980 S1 / SX980 S2 Service Supplement 15
3 Safety notes
IThe following safety instructions are also provided in the "Safety notes
and regulations" manual.
This device complies with the relevant safety regulations for data processing
equipment.
VCAUTION!
The actions described in these instructions should only be performed by
service personnel.
Before operating the device
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.
Installation and operation
VCAUTION!
●Never connect or disconnect data transmission lines during a storm
(lightning hazard).
●Make sure that no objects (such as bracelets or paper clips) fall into
or liquids spill into the device (risk of electric shock or short circuit).
●Proper operation of the device (in accordance with IEC 60950/
EN 60950) is only ensured if the casing is completely assembled and
the rear covers for the installation openings have been put in place
(electric shock, cooling, fire protection, interference suppression).

16 Service Supplement SX980 S1 / SX980 S2
Safety notes
Modules with electrostatic-sensitive components:
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●Remove the power plug from the power socket before inserting or removing
components containing ESDs.
●You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●The equipment and tools you use must be free of static charges.
●Only touch the components at the positions highlighted in green
(Touchpoints).
●Do not touch any exposed pins or conductors on a component.
●Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install components.
●Place all components on a static-safe base.
IYou will find a detailed description for handling ESD components in the
relevant European or international standards (DIN EN 61340-5-1,
ANSI/ESD S20.20).

SX980 S1 / SX980 S2 Service Supplement 17
4 Replacement routines
In case of an error the following parts can be replaced:
– Complete storage blade
IInformation about the replacement procedure of the hard disk drives you
will find in the "PRIMERGY Connection Blade SAS Switch 6 Gb 18/6
Operating Manual".
You have to change the remaining parts as a whole unit.
VCAUTION!
Observe the safety instructions in chapter "Safety notes" on page 15.
4.1 Preparation
To remove the storage blade from the system unit, you must first switch off the
related server blade(s).
4.1.1 Removing the storage blade from the system unit
IYou will find a detailed description of removing / installing the storage
blade out of/into the system unit in the SX980 S1 / SX980 S2 storage
blade Operating Manual.
ÊSwitch off the related server blade(s): either using the On/Off button on the
server blade or using the Web interface of the management blade (see the
user interface description in the manual „ServerView Management
Blade S1" for PRIMERGY BX900 Blade Server Systems respectively for
PRIMERGY BX400 Blade Server Systems).
ÊUndo the locking mechanism of the release lever.
ÊSwivel the release lever until it is nearly horizontal.
ÊPull the storage blade out of the slot.

18 Service Supplement SX980 S1 / SX980 S2
Replacement routines
4.2 Replacing the complete storage blade
You have to change the remaining parts as a whole unit. The cabling in the
spare part "SX980 S1 / SX980 S2 storage blade complete with cables" is
already installed.
ÊExit all applications and shut down the related server blade correctly.
ÊMake a note of the positions of the individual HDD/SSDs in the storage
blade for reinstallation.
ÊOnly for the japanese market:
Remove the storage blade as described in section "Removing the storage
blade from the system unit" on page 17.
Use the cover from the defective storage blade.
IIt is necessary to copy the model name and the serial number
described in the label that exists in the ID card. Please use a new
label.
ÊInsert the new storage blade in the system unit.
IYou insert the storage blade in the opposite order to that described in
"Removing the storage blade from the system unit" on page 17.

SX980 S1 / SX980 S2 Service Supplement 19
5 Appendix
5.1 PRIMERGY SX980 S1
5.1.1 SX980 S1 storage blade as spare part
Part number: S26361-K1383-V901
The spare part contains all the components shown below.
Figure 2: SX980 S1 storage blade as spare part (with cables)
Pos. Description
1 Control Panel
2 Drive Backplane
3 Expander Board
4 Interposer Board
5 SAS Connection Board
0
/
12

20 Service Supplement SX980 S1 / SX980 S2
Appendix
5.1.2 SX980 S1 storage blade cable plan
Figure 3: Cable plan for SX980 S1 storage blade
X103
X102
SAS
Connection
Board 1
X1
X2
Expander Board 1
Drive Backplane
X13
X11
X12
Interposer Board
X104
X103
X102 X105 Control Panel
X103
X102
SAS
Connection
Board 2
Key: Signal
Power
SAS
P1
P2