Fujitsu BS2000 User manual

Edition June 2015
© Siemens Nixdorf Informationssysteme AG 1995 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.vor
English
SE700 / SE500 / SE300
Server Unit x86
FUJITSU Server BS2000
Operating Manual

Comments…Suggestions…Corrections…
The User Documentation Department would like to know your
opinion on this manual. Your feedback helps us to optimize our
documentation to suit your individual needs.
Feel free to send us your comments by e-mail to:
[e-mail]
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system which
complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
This manual is printed
on paper treated with
chlorine-free bleach.
Copyright © 2015 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
The Xen® mark is a trademark of Citrix Systems, Inc., which manages the mark on behalf of the Xen open source
community. The Xen® mark is registered with the U.S. Patent and Trademark Office, and may also be registered in
other countries.
Novell and SUSE are registered brands of Novell, Inc. in the USA and other countries.
Linux is a registered brand of Linus Torvalds.
Windows® is a registered trademark of Microsoft Corporation.
The Linux-based basic software M2000, X2000, and HNC which is installed on the Management Unit,
Server Unit x86, and HNC contains Open Source Software. The licenses for this can be found in the LICENSES
directory on the relevant installation DVD

U41860-J-Z126-1-76
Dokuschablonen 19x24 Version 7.4de für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010
29. Juni 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.ivz
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Server Unit SU300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Switching the Server Unit on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.1 Switching the Server Unit on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.2 Switching the Server Unit off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Front of the Server Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2.1 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.2 Indicators on the operating panel . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.3 Indicators on the operable drives/components . . . . . . . . . . . . . . . . . . . . . 14
2.2.4 Hard disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2.5 DVD-RW drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.5.1 Components of the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.5.2 Inserting a CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.5.3 Removing a CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.5.4 Removing a CD/DVD manually . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.5.5 Precautionary measures when handling CDs and DVDs . . . . . . . . . . . . . 18
2.3 Rear of the Server Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3 What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1 Performing a system dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2 Creating diagnostic documentation . . . . . . . . . . . . . . . . . . . . . . . . . 26

Contents
U41860-J-Z126-1-76
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

U41860-J-Z126-1-76 5
Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010
Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010
29. June 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.k01
1 Introduction
The FUJITSU Server BS2000 SE Series unites the existing server lines S servers and SQ
servers in the server line SE servers.
Depending on requirements, the SE server contains all the system components needed for
operation as an overall application:
– /390-based BS2000 Server Unit
– x86-based Server Units with BS2000, Linux or Windows guest systems
– x86-based Application Units for operation under Linux, Windows or VMware
– Shareable tape and disk periphery
– A high-speed, server-internal infrastructure to connect the components with each other
and with the customer LAN or SAN.
The SE700 / SE500 / SE300 Operating Manual, which consists of a number of modules,
describes the features and hardware components of the FUJITSU Server BS2000 of the
SE Series. Users should read the operating manuals carefully in order to obtain optimal
performance from the SE server.
This manual describes the hardware component Server Unit x86 and complements the
Basic Operating Manual [1]. You will find a comprehensive introductory chapter in the Basic
Operating Manual . The chapters "Important notes" chapter on SE server operation and
"Environmental protection and service" are contained only in the Basic Operating Manual .

6 U41860-J-Z126-1-76

U41860-J-Z126-1-76 7
Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010
Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010
29. June 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.k03
2 Server Unit SU300
This section describes the Server Unit SU300. SE300 is equipped with an SU300 as the
first Server Unit. SE300, SE500 and SE700 can optionally be equipped with one or two
additional Server Units SU300.
iComponents and ports which are not used are not described below.
In the SU300 the base system X2000 enables BS2000 to execute (in Native mode or on
BS2000 VMs). Optionally X2000 enables Linux/Windows systems to operate in parallel on
XenVMs.
A SU300 occupies four height units (HUs) in the rack.
Features
– 16 models are available with up to 16 BS2000 processors. Capacity on Demand
permits temporary processor attachment.
– Depending on the model, the size of the main memory (for BS2000 and for the base
system X2000) is 32 to 64 GB in the basic configuration. All models can be enhanced
to 1504 GB.
– For the input/output system the Server Unit contains two 2.5'' SATA hard disks, each
with a capacity of 600 GB in size in the basic configuration, which are mirrored.
– The Server Unit contains a DVD-RW drive.
– Fibre Channels operating at 8 or 16 Gbps are available for connecting peripherals.
– At least one 4-port LAN card is connected on the Server Unit. The first two ports are
used for the connection to the Net Unit, and the other two can, if required, be used for
BS2000 applications. Optionally LAN controllers operating at 10 Gbps can also be
used.
– Each Server Unit is equipped with 4 power supply units. 2 + 2 redundancy in 2 phases
is thus guaranteed. If one phase fails completely, the Server Unit will continue to
operate.

Switching the Server Unit on/off Server Unit SU300
8 U41860-J-Z126-1-76
2.1 Switching the Server Unit on/off
Information on switching on and starting the SE server and on switching it off and shutting
it down is provided in the "Basic Operating Manual" [1], "Switching the server on and off".
2.1.1 Switching the Server Unit on
Before the Server Unit is switched on, the status indicator lights up green (item 5 in figure 2
on page 10).
ÊAs the administrator or a privileged operator, switch on the Server Unit using the
SE Manager (menu Hardware →Server (SE<model>, Units tab, "Switch on" function for
the Server Unit), see the “Operation and Administration” manual [5].
The power-on indicator lights up green. The Server Unit switches on, conducts a system
test and starts X2000.
If automatic IPL is configured for BS2000, the BS2000 system (Native or as a VM2000
monitor system) is also started with the configured settings.
If automatic startup is configured for XenVMs, these systems are also started.
2.1.2 Switching the Server Unit off
Before the Server Unit is switched off, the On/Off switch / status indicator lights up green,
and after the Server Unit has been switched off it no longer lights up (item 4 in figure 2 on
page 10).
ÊAs the administrator or a privileged operator, switch off the Server Unit using the
SE Manager (menu Hardware →Server (SE<model>, Units tab, "Switch off" function for
the Server Unit), see the “Operation and Administration” manual [5].
When the Server Unit is switched off, the BS2000 system is shut down properly taking into
account the remaining runtime specified.
The "Power cable connected" status indicator (item 5 in figure 2 on page 10) lights up green
when the server is switched off but connected to the power supply (power cable connected).
This status indicator does not light up in the following situations:
– The Server Unit is switched off and not connected to the power source.
– The Server Unit is switched on and operating normally.

Server Unit SU300 Front of the Server Unit
U41860-J-Z126-1-76 9
Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010
Dokuschablonen 19x24 Version 7.4us für FrameMaker V7.x vom 09.02.2010 © cognitas GmbH 2001-2010
29. June 2015 Stand 14:43.13 Pfad: P:\FTS-BS\Server\SE-Server\SE-Doku\1303908_BA_SU_x86\prod_e\ba_sux86.k03
2.2 Front of the Server Unit
Figure 1: Server Unit (front)
1 ID card (green) 5 Video port (for Customer Support only)
2 ServerView Local Service Display 6 3x USB ports (for Customer Support only)
3 Optical drive activity indicator 7 HDD indicators
4 Operating panel (for further details see figure 2
on page 10)
햲 햳 햴 햵햶햷
햸

Front of the Server Unit Server Unit SU300
10 U41860-J-Z126-1-76
Figure 2: Front - Detailed view: Operating panel
ID card
You can pull the ID card (see figure 1 on page 9) out and push it in again as far as it will go.
The ID card contains various system information, e.g. product name, serial number, MAC
addresses and DNS name.
1 ID button/ ID indicator 6 3x USB ports (for Customer Support only)
2 Reset button 7 Video port (for Customer Support only)
3 NMI button 8 HDD activity indicator
4 On/Off button / Status indicator 9 Global error indicator
5 Status indicator (power cable
connected)
10 CSS indicator
햲햳햴햵햷
햸
햹
햶
햺