Fujitsu PRIMERGY T850 User guide

PRIMERGY T850
System Configurator and Order Information Guide
Contents
Instructions
Configuration diagram
Configurator
0System software
IBasic unit
II Processor
III Memory
IV Graphics
VAccessible drives
VI Hard disk drives
VII SCSI / Fibre Channel controller
VIII Disk Array
IX Communication / Network
XSystem Management Products (RemoteView)
XI Miscellaneous
XII PCI Extension Box
XIII SCSI / Fibre Channel controller for PCI Extension Box
XIV Disk Array for PCI Extension Box
XV Communikation / Network for PCI Extension Box
XVI Communikation / Network for PCI Extension Box
Change report
PRIMERGY Server
October 2003

System configurator and order-information guide
PRIMERGY T850 Status 2003-09-23
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/ SystemArchitect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/ SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section III Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options.
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates.
4x
Please note that there are information symbols which indicate necessary information.
Further information in the internet see:
http://www.primergy.com
(internet)
http://extranet.fujitsu-siemens.com/primergy
(extranet)
Prices and availability see price list and PC-/ SystemArchitect.
Subject to change and errors excepted.
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 2 of 18

System configurator and order-information guide
PRIMERGY T850 Status 2003-09-23
Configuration diagram PRIMERGY T850
TOP VIEW FRONT/REAR VIEW
System unit ( I )
1st System Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
2nd System Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Xeon MP
Xeon MP
Xeon MP
Xeon MP
Xeon MP
Xeon MP
Xeon MP
Xeon MP
Processor ( II ) Memory ( III ) Processor ( II ) Memory ( III )
Extension slots
Two Power Supplies included
Graphics ( IV )
SCSI controller ( VII )
1st PS
2nd PS
Disk array ( VIII )
Communikation/Network ( IX )
6 PCI-X -slots, 1 slot occupied by RSB
Hot-plug 1+1 (redundant) Power Supply
PCI-X long 64 Bit / 133 MHz hot-plug 1050W at 220V or 525W at 110V each
PCI-X long 64 Bit / 133 MHz hot-plug
3.5"x0.5"
5.25"x0.5"
PCI-X long 64 Bit / 100 MHz hot-plug Floppy disk DVD
PCI-X long 64 Bit / 100 MHz hot-plug
PCI-X long 64 Bit / 66 MHz hot-plug Accessible drives ( V )
RemoteServiceBoard
(PCI-X long 64 Bit/66 MHz hot-plug) Hard disk drives ( VI )
hot plug
3.5"x1" 3.5"x1"
SCSI-drive
SCSI-drive
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 3 of 18

System configurator and order-information guide
Start "PRIMERGY T850"
PRIMERGY T850 Status 2003-09-23
SW Configurator
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
Later use of OEM operating system
Microsoft does not allowe software is not allowed,
Vmware-Software the use of OEM-software apart from OEM software by
- ESX Server 1.5 (OEM) under ESX. VMware and F5
- ESX Server 2.0 (OEM)(planned) Distributions-/ retailware is
- Virtual SMP for ESX 2.0 (OEM) allowed.
For all SW products listed below please refer to the corresponding software configurator accessible via the
Extranet under "PC Configurations, Configurator for PRIMERGY SW", URL see below.
MS - Software: W **) PRIMECLUSTER *)
- Windows 2000 Server - Clustering
- Windows 2000 Advanced Server - Load Balancing
- Windows 2000 Data Center Server
(only for certified systems)
- Windows Server 2003, Linux - Software: **)
Standard Edition - SuSE Linux Enterprise Server: S
Enterprise Edition - SuSE Professional Linux
- Red Hat Enterprise Linux
- Red Hat Professional Linux
CITRIX-Software für NT: W1
- Multiuser SW MetaFrame
LoadBalancing
Additional User Licences
MultiPath, Duplex Data easy Mirror for Linux
Manager for NT; W2K; Linux NT 4, WIN 2000
FSC System Management
Software: V *) Pay attention to release information on datasheet under
- RemoteView Software
http://www.primecluster.com
- RemoteView Service Board
- RemoteView Diagnosis **) Pay attention to release and order information in PRINCE -> Operating System
http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm
Backup-Software: U
- ARCserve for NT
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users:
http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm
for partners:
http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm
Continue with PRIMERGY
HW configurator
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 4 of 18

System configurator and order-information guide
Start PRIMERGY T850
PRIMERGY T850 Status 2003-09-23
Section IBasic unit
System unit consisting of:
* 4U rack mountable housing incl. 2 hot plug power supply modules redundant
- temperature sensor for CPU module and FSC PDA function
* 4 hot replace fans
* Drives / Bays
- 1 drive bay 3.5“/0.5“ high (occupied by 1 floppy disk
- 1 drive bay 5.25"/0.5" high (occupied by 1 DVD-ROM)
- 2 bays for 1“ hard disks
- 6 slots PCI-X 64 Bit (2x 133 MHz, 2x 100 MHz, 2x 64 MHz, (1x occupied by 1 RemoteView serviceboard)
Systemboard, to upgrade to 4 or up to 8 processors with:
- 2x Xeon processors, 100 MHz quad-pumped FSB
- 2-channel U160 SCSI controller on-board
- graphics processor on board 8 MB (PCI)
- LAN Controller 10/100/1000 on-board
- Fast-IDE controller (for DVD-ROM)
- RemoteView Serviceboard in a PCI slot
External Interfaces:
- 1x RS-232-C (serial, 9 pin)
- 1x keyboard (PS/2)
- 1x mouse (PS/2)
- 1x VGA (15 pin)
- 3x USB UHCI (1x front side)
- 1x LAN RJ45
- 3x SMP Interconnect
- 1x PCI extension
- 1x SCSI U160 (UHD68)
Cables:
1. IDE cable for CD/DVD
2. U160 SCSI cable for connection of the HD backplane
3. Power cord
Software:
- ServerStart packet incl. ServerBooks CD, ServerSupport CD and ServerView
Mounting kit for PRIMERGY T850 is part of the basic unit
- 1 pair of telescopic rails (710-815mm)
- 1 pair of carrier rails
- 1 bracket PC-Rack
- 1 cable management PC-racks
Mounting kit for mounting of servers in in FSC 19" PRIMECENTER- racks
and all server racks conforming to EIA standard EIA-310-D for 19" racks.
Therefore the mounting kit is variable in deepth from 710-815mm
A
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 5 of 18

System configurator and order-information guide
A
PRIMERGY T850 Status 2003-09-23
Rack Basic Unit (4U), 8-way Rack Basic Unit (4U), 4-way
including 2x Xeon MP processor including 2x Xeon MP processor
2 system boards 1 system board
upgradable to 8 CPUs upgradable to 4 CPUs
S26361-K846-V815 1,5 GHz / 1MB S26361-K846-V415 1,5 GHz / 1MB
S26361-K846-V819 1,9 GHz / 1MB S26361-K846-V419 1,9 GHz / 1MB
S26361-K846-V820 2,0 GHz / 2MB S26361-K846-V420 2,0 GHz / 2MB
16-way Upgrade S26361-F2738-L308
Requires two Rack Basic Units Ugrade System Board
fully equipped with 8 prcessors each. without processor
Only available after Special Release enables upgrade to 8 CPUs
is granted. max. 1x per system
For Windows 2000 Datacenter or
VMware 1.5 only. If two system boards are installed, both have
S26361-F2738-E316 to be equipped with processors and memory
The 16-way configuration is only
available on request of an
Special Release.
PRIMECENTER Rack
SNP:SY-F1647E301-P "Rack-mounting ex factory"
Installation ex works for one This service is to be ordered once
server or subsystem. per installable server/storage
Hereby the rack will be delivered subsystem, in order to get the
completely pre-mounted and server/storage subsystem
all wired connections are tested. mounted into the PRIMERGY racks.
With racks 12U, 24U, 38U: In case of the 46 U PRIMERGY Rack,
Systems and components this service has to be ordered,
will be delivered installed in the rack to get the mounting kits and the
With racks 46U: cables installed.
Systems and components
will be delivered separately
To be ordered only together with
a PRIMERGY-
PRIMECENTER rack
e.g.:
S26361-K826-V10x
refer configurator PC-Rack
max. 1x per System
B
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 6 of 18

System configurator and order-information guide
B
PRIMERGY T850 Status 2003-09-23
Section II Processor
The PRIMERGY T850 can carry up to 2 system boards.
The basic units include either one or two system boards.
Please note that the basic units already includes two processors.
Each system board requires at least 1 processor can be upgraded to max. 4 processors.
Only processors with the same clock frequency and the same third level cache (TLC) can be used.
Terminators are automatically included if necessary.
For a multi-processor system a multi-processor operating system is required.
Important: The necessary operating system license depends possibly on the number of the processors,
e.g. with Windows 2000 Datacenter and the pertinent update subscription.
Also with additional processor armaments it can be that the licensed CPU number is exceeded.
Then an appropriate license must be ordered. See also for this W2k Datacenter Product Facts, chapter 5
S26361-F2740-E151 S26361-F2740-E191 S26361-F2740-E202
XEON MP 1,5GHz XEON MP 1,9GHz XEON MP 2GHz
with 1 MB TLC on Chip, with 1 MB TLC on Chip, with 2MB TLC on Chip,
heat sink heat sink heat sink
occupies slot for one CPU occupies slot for one CPU occupies slot for one CPU
max. 2x for 1 system board max. 2x for 1 system board max. 2x for 1 system board
max. 6x for 2 system boards max. 6x for 2 system boards max. 6x for 2 system boards
C
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 7 of 18

System configurator and order-information guide
C
PRIMERGY T850 Status 2003-09-23
Section III Memory
There are 16 memory slots available (4 banks with 4 modules each) on each system board.
Mixing different modules within a bank is not support,
therefore only complete banks with 4 modules are offered
Each system board must be pupolated with at least 1 bank
Memory mirroring functionality is possible as an option between banks
S26361-F2741-E142 S26361-F2741-E144
max. 4x Main memory 2.048 MB Main memory 4.096 MB
per 133 MHz Registered SDRAM 133 MHz Registered SDRAM
system
board consisting of 4 modules consisting of 4 modules
occupies one bank occupies one bank
max. 4x per system board max. 4x per system board
Section IV Graphics
Graphics controller other than the 8MB on-board controller (S3 Savage4) are not tested and released.
D
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 8 of 18

System configurator and order-information guide
D
PRIMERGY T850 Status 2003-09-23
Section VAccessible Drives
The Basic Unit includes one Floppy Disk and one DVD Drive.
Other integrated accessable drives are not supported.
Section VI Hard Disk Drives
while stocks last
SNP:SY-F2336E118-P SNP:SY-F2336E136-P
Hard disk 18GB Hard disk 36GB
10000rpm, <7ms, min. 4MB Cache 10000rpm, <7ms, min. 4MB Cache
U160 SCSI (160 MB/sec) U160 SCSI (160 MB/sec)
Interface: WIDE SCA (80 pins) Interface: WIDE SCA (80 pins)
hot pluggable drive hot pluggable drive
occupies 1" bay occupies 1" bay
max. 2x per system max. 2x per system
S26361-F2336-E173 S26361-F2336-E114
Hard disk 73GB Hard disk 146GB
10000rpm, <7ms, min 8MB Cache 10000rpm,<5,5ms,min. 8MB Cache
U160 SCSI (160 MB/sec) Ultra 160 SCSI (160MB/s)
Interface: WIDE SCA (80 pins) Interface: Wide SCA (80-pins)
max. 2x hot pluggable drive hot pluggable drive
occupies 1" bay occupies 1" bay
max. 2x per system max. 2x per system
S26361-F2336-E518 S26361-F2336-E536 S26361-F2336-E573
Hard disk 18GB Hard disk 36GB Hard disk 73GB
15000rpm, <4ms, min. 8MB Cache 15000rpm, <4ms, min. 8MB Cache 15000rpm, <4ms, min. 8MB Cache
Ultra 160 SCSI (160MB/s) Ultra 160 SCSI (160MB/s) Ultra 160 SCSI (160 MB/sec)
Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins)
hot pluggable drive hot pluggable drive hot pluggable drive
occupies 1" bay occupies 1" bay occupies 1" bay
max. 2x per system max. 2x per system max. 2x per system
E
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 9 of 18

System configurator and order-information guide
E
PRIMERGY T850 Status 2003-09-23
Section VII SCSI/Fibre Channel Controller
Inclusive The two HD SCSI drives are connected to one on-board SCSI channel.
The 2nd channel of the Dual- The second on-board SCSI channel can be used for external devices.
on-board U2W-SCSI controller
can be used for external drives
Included in the basic and system
units.
Controller for the connection of an external storage system:
S26361-F2399-E1 not released for
SCSI 160 controller VMware ESX Server
Adaptec SCSI card 29160
1 channel: LVD+Fast/Ultra (decoup.)
LVD con. for HD, withoud cable
Fast/Ultra con. access. drives
64/66 (32/33) PCI, min. 180mm
int: Fast 50-pin or Ultra HD68
+ LVD HD68; ext: HD68(LVD)
SW:
max. 2x per system
Fibre Channel controller for subsystems and SAN
while stocks last while stocks last
SNP:SY-F2244E1-A SNP:SY-F2244E2-A
1GBit/s FC Controller 1GBit/s FC Controller
Qlogic Qlogic
QLA 2200 QLA 2200F
1 Channel 1GBit/sec FC Controller 1 Channel 1GBit/sec FC Controller
CU (copper) Interface MMF(Multimode Fibre) Interface
incl. SW and description (Ger/US) incl. SW and description (Ger/US)
PCI 64Bit / 66MHz, 175mm PCI 64Bit / 66MHz, 175mm
3.3V and 5V tolerant signaling 3.3V and 5V tolerant signaling
4x max. 4x per system max. 4x per system while stocks last
S26361-F2843-E1 S26361-F2624-E1 Attention
2GBit/s FC Controller 2GBit/s FC Controller 2GBit/s FC Controller
Emulex Emulex require other interface
LP9802 LP9002L connectors for the
1 Cannel 2GBit/sec FC Controller 1 Channel 2GBit/sec FC Controller optical cables than
LC Interface for 50um Fiber LC Interface for 50um Fibre 1GBit/s fibre channel.
PCI 64Bit / 133MHz, 170mm PCI 64Bit / 66MHz, 170mm
3.3V and 5V tolerant signaling 3.3V and 5V tolerant signaling
max. 4x per system max. 4x per system
freigegeben
There are other components such as switches, GBICs or cables which can be ordered for fibre channel SAN attachments. (see price list)
All controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
All internal cables and adapters are included within the basic units and components respectively.
F
Fujitsu Siemens Computers
Enterprise Products - PRIMERGY Server 10 of 18