Fujitsu PRIMERGY TX1310 M1 User manual

Operating Manual - English
FUJITSU Server PRIMERGY TX1310 M1
Operating Manual
Edition May 2014

Copyright and Trademarks
Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected]su.com.
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright © 2014 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any without the prior written permission of
Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

TX1310 M1 Operating Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.

Operating Manual TX1310 M1
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market: About SATA hard disk drives
The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://jp.fujitsu.com/platform/server/primergy/harddisk/

TX1310 M1 Operating Manual
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Concept and target groups for this manual . . . . . . . . . . 9
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . 11
1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . 12
2 Functional overview . . . . . . . . . . . . . . . . . . . . . . 13
2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 Server specification . . . . . . . . . . . . . . . . . . . . . . 17
3 Installation steps, overview . . . . . . . . . . . . . . . . . . 23
4 Important information . . . . . . . . . . . . . . . . . . . . . 25
4.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 25
4.2 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3 FCC Class A Compliance Statement . . . . . . . . . . . . . 34
4.4 Transporting the server . . . . . . . . . . . . . . . . . . . . 35
4.5 Environmental protection . . . . . . . . . . . . . . . . . . . 36
5 Hardware installation . . . . . . . . . . . . . . . . . . . . . . 39
5.1 Unpacking the server . . . . . . . . . . . . . . . . . . . . . 40
5.2 Setting up the server . . . . . . . . . . . . . . . . . . . . . . 41
5.3 Connecting devices to the server . . . . . . . . . . . . . . . 42
5.4 Connecting the server to the mains . . . . . . . . . . . . . . 43
5.5 Notes on connecting/disconnecting cables . . . . . . . . . 45

Operating Manual TX1310 M1
Contents
6 Starting up and operation . . . . . . . . . . . . . . . . . . . . 47
6.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 47
6.2 Control elements and indicators . . . . . . . . . . . . . . . . 48
6.2.1 Front of the server . . . . . . . . . . . . . . . . . . . . . . . . 48
6.2.1.1 Control elements . . . . . . . . . . . . . . . . . . . . . . . 49
6.2.1.2 Indicators on the control panel . . . . . . . . . . . . . . . . 49
6.2.2 Rear of server . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.2.2.1 Indicators on the connector panel: LAN indicators . . . . . . 50
6.3 Switching the server on and off . . . . . . . . . . . . . . . . 51
6.4 Configuring the server . . . . . . . . . . . . . . . . . . . . . 55
6.4.1 Configuring the onboard SATA controller . . . . . . . . . . . . . 55
6.4.2 Configuring the server and installing the operating system
with the ServerView Installation Manager . . . . . . . . . . . . . 56
6.4.3 Configuring the server and installing the operating system
without the ServerView Installation Manager . . . . . . . . . . . 57
6.5 Cleaning the server . . . . . . . . . . . . . . . . . . . . . . . 58
7 Property and data protection . . . . . . . . . . . . . . . . . . 59
7.1 BIOS Setup security functions . . . . . . . . . . . . . . . . . 59
8 Troubleshooting and tips . . . . . . . . . . . . . . . . . . . . 61
8.1 Power-on indicator remains unlit . . . . . . . . . . . . . . . . 61
8.2 Server switches itself off . . . . . . . . . . . . . . . . . . . . 62
8.3 Screen remains blank . . . . . . . . . . . . . . . . . . . . . . 62
8.4 Flickering stripes on monitor screen . . . . . . . . . . . . . 63
8.5 No screen display or display drifts . . . . . . . . . . . . . . . 63
8.6 No mouse pointer displayed on screen . . . . . . . . . . . . 63
8.7 Incorrect date and time . . . . . . . . . . . . . . . . . . . . . 64
8.8 Error message on screen . . . . . . . . . . . . . . . . . . . . 64
8.9 Expansion cards or onboard devices not recognized . . . . 64
8.10 Temperature warning . . . . . . . . . . . . . . . . . . . . . . 65

TX1310 M1 Operating Manual
Contents
8.11 No effect of keyboard or mouse . . . . . . . . . . . . . . . . 65
8.12 Optical drive cannot read data . . . . . . . . . . . . . . . . 65

Operating Manual TX1310 M1
Contents

TX1310 M1 Operating Manual 9
1 Introduction
The PRIMERGY TX1310 M1 server is an Intel-based server for workgroups and
small networks. The server is suitable for use as a file server and also as an
application, information or Internet server.
Thanks to its highly developed hardware and software components, the
PRIMERGY TX1310 M1 server offers a high level of data security and
availability.
Security functions in the BIOS-Setup and on the system board protect the data
on the server against manipulation. The supported RAID levels allow the hard
disk controllers to offer error tolerance, through data redundancy, for users who
want to provide complete protection for valuable data.
Its low noise level and high energy efficiency make it ideal for office
environments.
1.1 Concept and target groups for this manual
This operating manual describes how to install, set up and operate your server.
This operating manual is intended for those responsible for installing the
hardware and ensuring that the system runs smoothly. It contains all the
information you need to put your PRIMERGY TX1310 M1 into operation.
To understand the various expansion options, you will need to be familiar with
the fields of hardware and data transmission and you will require a basic
knowledge of the underlying operating system.

10 Operating Manual TX1310 M1
Introduction
Different versions for TX1310 M1
The PRIMERGY TX1310 M1 is available in different versions. Your base unit
may not have all functions described in this manual. The following table
provides an overview of the different features:
System board D3219-Axx D3219-Bxx
Main Memory 4 slots for 1600 MHz
memory modules DIMM
1A, 1B, 2A, 2B
2 slots for 1600 MHz memory
modules DIMM 1A, 1B
PCI slots Slot 1: PCIe x1 slot Gen 2
(mechanically x4)
Slot 2: PCIe x4 slot Gen 2
(mechanically x8)
Slot 3: PCIe x8 slot Gen 3
(mechanically x8,
notched)
Slot 4: PCIe x8 slot Gen 3
(mechanically x8,
notched)
Slot 1: not assembled
Slot 2: not assembled
Slot 3: PCIe x8 slot Gen 3
(mechanically x8, notched)
Slot 4: PCIe x8 slot Gen 3
(mechanically x8, notched)

TX1310 M1 Operating Manual 11
Introduction
1.2 Documentation overview
More information on your PRIMERGY TX1310 M1 can be found in the following
documents:
– "Quick Start Hardware - FUJITSU Server PRIMERGY TX1310 M1"
– "ServerView Quick Start Guide"
– "Safety Notes and Regulations" manual
"安全上のご注意 " for the Japanese market
– "Warranty" manual
"保証書 " for the Japanese market
– "ServerView Suite Local Service Concept - LSC" manual
– "Returning used devices" manual and "Service Desk" leaflet
"サポート＆サービス " for the Japanese market
– "FUJITSU Server PRIMERGY TX1310 M1 Upgrade and Maintenance
Manual"
– "D3219 BIOS Setup Utility for FUJITSU Server PRIMERGY TX1310 M1
Reference Manual"
IAll documentation on PRIMERGY hardware and ServerView software is
available online from the Fujitsu manuals server at:
–http://manuals.ts.fujitsu.com (global market)
–http://jp.fujitsu.com/platform/server/primergy/manual (Japanese market)
The complete PRIMERGY documentation set can also be downloaded
as a DVD ISO image at:
–ftp://ftp.ts.fujitsu.com/images/serverview/manuals (global market)
–http://jp.fujitsu.com/primergy/downloads (Japanese market)
Further sources of information:
– ServerView Suite Glossary
– Manual for the monitor
– Documentation for the boards and drives
– Operating system documentation
– Information files in your operating system

12 Operating Manual TX1310 M1
Introduction
1.3 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

TX1310 M1 Operating Manual 13
2 Functional overview
This section provides information on the features and technical data of the
PRIMERGY TX1310 M1 server. For information on key characteristics and
layout of the system board, see "D3219 BIOS Setup Utility for FUJITSU Server
PRIMERGY TX1310 M1 Reference Manual".
2.1 Features
Intel
®
processors
The server has Intel
®
Dual Core CPUs (Celeron
®
, Pentium
®
, Core i3) or Quad
Core CPUs (Xeon
®
E3-1200v3) for high-speed data processing.
System board
The features of the system board are described in the "FUJITSU Server
PRIMERGY TX1310 M1 Upgrade and Maintenance Manual", the setup
possibilities are described in the "D3219 BIOS Setup Utility for FUJITSU Server
PRIMERGY TX1310 M1 Reference Manual".
Trusted Platform Module (TPM)
A Trusted Platform Module (TPM) for safer storage of keys can be implemented
as an option. This module enables programs from third party manufacturers to
store key information (e.g. drive encryption using Windows Bitlocker Drive
Encryption).
The TPM is activated via the BIOS system (for more information, refer to the
“D3219 BIOS Setup Utility for FUJITSU Server PRIMERGY TX1310 M1
Reference Manual").
VCAUTION!
– When using the TPM, note the program descriptions provided by the
third party manufacturers.
– You must also create a backup of the TPM content. To do this, follow
the third party manufacturer's instructions. Without this backup, if the
TPM or the system board is faulty you will not be able to access your
data.

14 Operating Manual TX1310 M1
Functional overview
– If a failure occurs, please inform your service about the TPM
activation before it takes any action, and be prepared to provide them
with your backup copies of the TPM content.
Hard disk drives
Up to four SATA hard disk drives, each with a maximum height of 1 inch, are
built into the drive cages. There is a wire connection to the controller.
The server comes with an onboard SATA controller.
Onboard SATA controller
A SATA controller is integrated on the system board; up to four SATA hard disk
drives can be connected to the controller. The LSI Embedded MegaRAID
software (SATA Software RAID) supports RAID levels 0, 1 and 10.
The SATA HDDs cannot be replaced during operation.
For more information on configuring the controller, see section "Configuring the
onboard SATA controller" on page 55.
Accessible drives
The first (top) bay contains the server's DVD drive.
The 5.25-inch bay below is available for one additional accessible drive
(CD/DVD drives or RDX device).
The accessible drives cannot be replaced during operation.
Power supply
The server has a permanently installed power supply unit that adjusts
automatically to any mains voltage in the range 100 V - 240 V.
High level of availability and data security
When memory data is accessed, 1-bit errors are identified in the main memory
and automatically corrected with the error correcting code (ECC) method.
ASR&R (Automatic Server Reconfiguration and Restart) restarts the system in
the event of an error and automatically "hides" the defective system
components.

TX1310 M1 Operating Manual 15
Functional overview
The PDA (Prefailure Detection and Analysis) technology from Fujitsu analyzes
and monitors all components that are critical for system reliability.
Server management
Server management is implemented using the ServerView Operations Manager
supplied and the PDA (Prefailure Detection and Analysis) technology from
Fujitsu. PDA reports the threat of a system error or overload at an early stage,
allowing preventive measures to be taken.
The ServerView Operations Manager enables the management of all
PRIMERGY servers in the network via a central console. The ServerView
Operations Manager supports the following functions:
● Round-the-clock monitoring, regardless of server status
● Temperature monitoring of the CPU and the ambient temperature
● Detailed status and error reports for processors and main memory
● Watchdog timer for Automatic Server Reconfiguration and Restart (ASR&R)
in the event that memory modules or processors fail
● Watchdog timer for monitoring the operating system with ASR&R
Further information on the ServerView Operations Manager is provided in the
associated documentation.
ServerView Installation Manager
You can configure the PRIMERGY server quickly and precisely with the
ServerView Installation Manager software provided. User-guided menus are
available for installing the server operating system (for further details see
section "Configuring the server" on page 55).

16 Operating Manual TX1310 M1
Functional overview
Service and support
PRIMERGY servers are easy to maintain and modular, thus enabling quick and
simple maintenance.
The handles and locks (touch point) used to exchange components are colored
green to ensure simple and immediate recognition.
In order to prevent the components from being damaged by incorrect handling
when they are being installed and removed, the areas of all components that
can be touched without damaging them are also marked green.
The Flash EPROM program supplied with the Fujitsu utilities supports a fast
BIOS update.
ServerView Remote Management
ServerView Remote Management is the remote management solution from
Fujitsu for PRIMERGY servers. ServerView Remote Management and the
relevant hardware components integrated on the system board allow remote
monitoring and maintenance as well as fast restoration of operation in the event
of errors.
Remote monitoring and maintenance avoids time-consuming and costly on-site
repairs and reduces service costs. This leads to a reduction in the total cost of
ownership and an excellent return on investment for the remote management
solution.

TX1310 M1 Operating Manual 17
Functional overview
2.2 Server specification
This section explains the specifications for the server. The specifications for this
server are liable to be updated without any notice. Please be forewarned.
System Board
Processor
Memory Modules Configuration
IConfiguration options may vary depending on base unit (see "Different
versions for TX1310 M1" on page 10).
System board type D3219
Coin type CR2032
Chipset Intel
®
C226
Processor quantity and
type
1x Intel
®
Dual Core CPUs or Quad Core CPUs
E3-1200v3 series
Memory slots 4
Memory slot type DIMM (DDR3)
Memory capacity
(min. - max.)
4 GB - 32 GB
2 GB - 32 GB (for the Japanese market)
Memory protection ECC
Memory notes 1600 MHz memory modules with 4, or 8 GB
1600 MHz memory modules with 2, 4, or 8 GB (for
the Japanese market)

18 Operating Manual TX1310 M1
Functional overview
Interfaces
Onboard or integrated controllers
Slots
IConfiguration options may vary depending on base unit (see "Different
versions for TX1310 M1" on page 10).
Drive bays
USB connectors USB 3.0 (2x front, 2x rear), USB 2.0 (4x rear), USB
3.0 (1x internal) for backup drives
Graphics (15-pin) 1x VGA
Serial 1 (9-pin) 1x serial RS-232
LAN / Ethernet (RJ-45) 2x Gbit/s Ethernet
Serial ATA total 6
RAID Controller RAID level 0, 1, 10
SATA Controller Embedded in Intel
®
Chipset C226
®
LAN Controller Single chip GbE Ethernet controller Intel® i210
onboard,
Single chip GbE Ethernet PHY Intel® i217LM,
2 x 10/100/1000 Mbit/s, PXE-Boot by LAN via PXE-
Server, Teaming supported
Trusted Platform
Module (TPM)
Infineon / 1.2 (option)
PCI-Express Gen3 x8 2x (mechanically x8) both notched
PCI-Express Gen2 x4 1x (mechanically x8)
PCI-Express Gen2 x1 1x (mechanical x4)
Hard disk bay
configuration
4x 3,5-inch SATA
Accessible drives 2 (one bay is occupied by DVD/DVD-RW, 5.25-inch)

TX1310 M1 Operating Manual 19
Functional overview
Operating Panel
Dimensions / Weight
Ventilation clearance
At least 200 mm on the front and rear.
Ambient conditions
Condensation during operation must be avoided!
Noise level
Operating buttons On/off switch
Status LEDs Power (green)
HDD access Access to HDD
Tower (W x D x H) 175 x 419 x 395 mm
Weight max. 14 kg (depending on configuration)
Environment class 3K2
Environment class 2K2
EN 60721 / IEC 721 Part 3-3
EN 60721 / IEC 721 Part 3-2
Temperature:
Operation (3K2) 10 °C ... 35 °C
Transport (2K2) -25 °C ... 60 °C
Humidity 10% ... 85% (non condensing)
Sound power level L
WAd
(ISO 9296) < 3.7 B (standby)
< 4.0 B (operation)
Sound pressure level at adjacent position
L
pAm
(ISO 9296)
< 24 dB (A) (standby)
< 24 dB (A) (operation)

20 Operating Manual TX1310 M1
Functional overview
Electrical values
Power supply
configuration
Standard power supply
Max. output 250 W
Rated voltage range 100 V - 240 V
Rated frequency range 50 Hz - 60 Hz
Rated current max. 3.5 A – 1.5 A (100 V / 240 V)