Fujitsu PRIMEQUEST 1000 Series Instruction sheet

C122-E155-05EN
FUJITSU Server
PRIMEQUEST 1000
Series
SAN Boot Environment Configuration Manual

i
Preface
This manual is a revised version of APPENDIX D Configuring the SAN Boot Environment from the
PRIMEQUEST 1000 Series Installation Manual (C122-E107EN). The manual describes procedures for
installing the SAN boot environment and provides the latest information including notes on design.
The manual describes the procedures applicable to the following UEFI driver versions:
FC SAN boot: Procedures for setting UEFI driver version 4.00a1 or earlier and version 4.12a7 or later
FCoE SAN Boot: Procedures for setting UEFI driver version 5.01A13 or later
The manual is intended for system administrators.
For details on the regulatory compliance statements and safety precautions, see the PRIMEQUEST 1000 Series
Safety and Regulatory Information (C122-E115EN).
Errata and addenda for the manual
PRIMEQUEST 1000 Series Errata and Addenda (C122-E119EN) provides errata and addenda for the manual.
Read the PRIMEQUEST 1000 Series Errata and Addenda (C122-E119EN) thoroughly in reference to the
manual.
For Safe Operation
How to use this manual
This manual contains important information about the safe use of this product. Read the manual thoroughly to
understand the information in it before using this product. Be sure to keep this manual in a safe and convenient
location for quick reference.
Fujitsu makes every effort to prevent users and bystanders from being injured and to prevent property damage.
Be sure to use the product according to the instructions in the manual.
About this product
This product is designed and manufactured for standard applications. Such applications include, but are not
limited to, general office work, personal and home use, and general industrial use. The product is not intended
for applications that require extremely high levels of safety to be guaranteed (referred to below as
"safety-critical" applications). Use of the product for a safety-critical application may present a significant risk
of personal injury and/or death. Such applications include, but are not limited to, nuclear reactor control, aircraft
flight control, air traffic control, mass transit control, medical life support, and missile launch control.
Customers shall not use the product for a safety-critical application without guaranteeing the required level of
safety. Customers who plan to use the product in a safety-critical system are requested to consult the Fujitsu
sales representatives in charge.

ii
Storage of accessories
Keep the accessories in a safe place because they are required for server operation.
Organization and Notation of This Manual
This section describes the following topics:
- Organization of this manual
- Manuals for the PRIMEQUEST 1000 series
- Related manuals
- Abbreviations
- Notation
- Notation for the CLI (command line interface)
- Notes on notations
- Alert messages
- Product operating environment
- Trademarks
Organization of this manual
This manual is organized as follows.
CHAPTER 1 Configuring the SAN Boot Environment
Chapter 1 describes the procedure for installing the SAN boot environment and provides notes on design.
CHAPTER 2 Settings on the Fiber Channel Card (FC Card)
Chapter 2 describes the settings to be made on the FC card to start the system from an LUN of the SAN
storage unit in the FC SAN boot environment.
CHAPTER 3 Settings on the Converged Network Adapter
Chapter 3 describes the settings to be made on the Converged Network Adapter to start the system from an
LUN of the SAN storage unit in the FCoE SAN boot environment.
CHAPTER 4 Installing Windows
Chapter 4 describes how to install Windows in the FC SAN boot environment.
CHAPTER 5 Installing RHEL
Chapter 5 describes how to install Red Hat Enterprise Linux (RHEL) in the FC SAN boot environment.
CHAPTER 6 Installing SUSE Linux Enterprise Server 11 Service Pack 2
Chapter 6 describes how to install SUSE Linux Enterprise Server 11 Service Pack 2 (SLES11 SP2) in the
FC SAN boot environment.
CHAPTER 7 Installing VMware
Chapter 7 provides a link to the guides provided by VMware, Inc.

iii
Manuals for the PRIMEQUEST 1000 series
The following manuals have been prepared to provide you with the information necessary to use the
PRIMEQUEST 1000 series.
You can access HTML versions of these manuals at the following sites:
Japanese-language site: http://jp.fujitsu.com/platform/server/primequest/manual/
Global site: http://jp.fujitsu.com/platform/server/primequest/manual-e/
Title
Description
Manual code
PRIMEQUEST 1000 Series
Getting Started Guide
Describes what manuals you should read and how to
access important information after unpacking the
PRIMEQUEST 1000 series server. (This manual
comes with the product.)
C122-E114XA
PRIMEQUEST 1000 Series
Safety and Regulatory
Information
Contains important information required for using the
PRIMEQUEST 1000 series safely. (This manual
comes with the product.)
C122-E115XA
PRIMEQUEST 1000 Series
Errata and Addenda
Provides errata and addenda for the PRIMEQUEST
1000 series manuals. This manual will be updated as
needed.
C122-E119EN
PRIMEQUEST 1000 Series
General Description
Describes the functions and features of the
PRIMEQUEST 1000 series.
C122-B022EN
SPARC
Enterprise/PRIMEQUEST
Common Installation
Planning Manual
Provides the necessary information and concepts you
should understand for installation and facility planning
for SPARC Enterprise and PRIMEQUEST
installations.
C120-H007EN
PRIMEQUEST 1000 Series
Hardware Installation
Manual
Includes the specifications of and the installation
location requirements for the PRIMEQUEST 1000
series.
C122-H004EN
PRIMEQUEST 1000 Series
Installation Manual
Describes how to set up the PRIMEQUEST 1000
series server, including the steps for installation
preparation, initialization, and software installation.
C122-E107EN
PRIMEQUEST 1000 Series
User Interface Operating
Instructions
Describes how to use the Web-UI and UEFI to assure
proper operation of the PRIMEQUEST 1000 series
server.
C122-E109EN

iv
Title
Description
Manual code
PRIMEQUEST 1000 Series
Administration Manual
Describes how to use tools and software for system
administration and how to maintain the system
(component replacement and error notification).
C122-E108EN
PRIMEQUEST 1000 Series
Tool Reference
Provides information on operation methods and
settings, including details on the MMB, PSA, and
UEFI functions.
C122-E110EN
PRIMEQUEST 1000 Series
Message Reference
Lists the messages that may be displayed when a
problem occurs during operation and describes how to
respond to them.
C122-E111EN
PRIMEQUEST 1000 Series
REMCS Installation Manual
Describes REMCS service installation and operation.
C122-E120EN
PRIMEQUEST 1000 Series
Glossary
Defines the PRIMEQUEST 1000 series related terms
and abbreviations.
C122-E116EN
PRIMEQUEST 1000 Series
SAN Boot Environment
Configuration Manual
Provides a revised version of APPENDIX D
Configuring the SAN Boot Environment from the
PRIMEQUEST 1000 Series Installation Manual
(C122-E107EN). The manual describes procedures for
installing the SAN boot environment and provides the
latest information including notes on design.
C122-E155EN
Related manuals
The following manuals relate to the PRIMEQUEST 1000 series.
You can access these manuals at the following site:
http://jp.fujitsu.com/platform/server/primequest/manual-e/
Contact your sales representative for inquiries about the ServerView manuals.
Title
Description
Manual code
ServerView Suite
ServerView Operations
Manager Quick Installation
(Windows)
Describes how to install and start ServerView
Operations Manager in a Windows environment.
None

v
Title
Description
Manual code
ServerView Suite
ServerView Operations
Manager Quick Installation
(Linux)
Describes how to install and start ServerView
Operations Manager in a Linux environment.
None
ServerView Suite
ServerView Installation
Manager
Describes the installation procedure using ServerView
Installation Manager.
None
ServerView Suite
ServerView Operations
Manager Server
Management
Provides an overview of server monitoring using
ServerView Operations Manager, and describes the
user interface of ServerView Operations Manager.
None
ServerView Suite
ServerView RAID
Management User Manual
Describes RAID management using ServerView RAID
Manager
None
ServerView Suite
Basic Concepts
Describes the basic concepts of ServerView Suite.
None
ServerView Operations
Manager
Installation ServerView
Agents for Linux
Describes installation and update installation of
ServerView Linux Agent.
None
ServerView Operations
Manager
Installation ServerView
Agents for Windows
Describes installation and update installation of
ServerView Windows Agent.
None
ServerView Mission Critical
Option User Manual
Describes the necessary functions unique to
PRIMEQUEST (notification via the MMB, hot
replacement command) and ServerView Mission
Critical Option (SVmco), which is required for
supporting these functions.
Also includes explanation of ServerView
Mission Critical Option for VM (SVmcovm)
required for VMware vSphere 5 server monitor.
None

vi
Title
Description
Manual code
ServerView RAID Manager
VMware vSphere ESXi 5
Installation Guide
ServerView Describes the installation and
settings required to use ServerView RAID
Manager on the VMware vSphere ESXi 5 server.
None
MegaRAID SAS Software
Provides technical information on using array
controllers.
Refer to the manual from the SVS-DVD2
supplied with the product or from the following URL:
The Fujitsu Technology Solutions manuals server
http://manuals.ts.fujitsu.com/
None
MegaRAID SAS Device
Driver Installation
Provides technical information on using array
controllers.
Refer to the manual from the SVS-DVD2
supplied with the product or from the following URL:
The Fujitsu Technology Solutions manuals server
http://manuals.ts.fujitsu.com/
None
Modular RAID Controller
Installation Guide
Provides technical information on using array
controllers.
Refer to the manual from the SVS-DVD2
supplied with the product or from the following URL:
The Fujitsu Technology Solutions manuals server
http://manuals.ts.fujitsu.com/
None

vii
Abbreviations
This manual uses the following product name abbreviations.
Formal product name
Abbreviation
Red Hat(R) Enterprise Linux(R) 5 (for Intel64)
Linux
RHEL5, RHEL
Red Hat(R) Enterprise Linux(R) 5 (for x86)
Red Hat(R) Enterprise Linux(R) 6 (for Intel64)
Linux
RHEL6, RHEL
Red Hat(R) Enterprise Linux(R) 6 (for x86)
Microsoft(R) Windows Server(R) 2003, Standard Edition
Windows
Windows Server 2003
Microsoft(R) Windows Server(R) 2003, Enterprise Edition
Microsoft(R) Windows Server(R) 2003, Datacenter Edition
Microsoft(R) Windows Server(R) 2003, Standard x64 Edition
Microsoft(R) Windows Server(R) 2003, Enterprise x64 Edition
Microsoft(R) Windows Server(R) 2003, Datacenter x64 Edition
Microsoft(R) Windows Server(R) 2003 R2, Standard Edition
Microsoft(R) Windows Server(R) 2003 R2, Enterprise Edition
Microsoft(R) Windows Server(R) 2003 R2, Datacenter Edition
Microsoft(R) Windows Server(R) 2003 R2, Standard x64 Edition
Microsoft(R) Windows Server(R) 2003 R2, Enterprise x64 Edition
Microsoft(R) Windows Server(R) 2003 R2, Datacenter x64 Edition
Microsoft(R) Windows Server(R) 2008 Standard
Windows
Windows Server 2008
Microsoft(R) Windows Server(R) 2008 Enterprise
Microsoft(R) Windows Server(R) 2008 Datacenter
Microsoft(R) Windows Server(R) 2008 R2 Standard
Microsoft(R) Windows Server(R) 2008 R2 Enterprise
Microsoft(R) Windows Server(R) 2008 R2 Datacenter
Microsoft(R) Windows Server(R) 2012 Datacenter
Windows
Windows Server 2012
Microsoft(R) Windows Server(R) 2012 Standard
VMware vSphere(R) 4
VMware, vSphere 4.x,
VMware 4.x
VMware vSphere(R) 5
VMware, vSphere 5.x,
VMware 5.x
VMware(R) ESX(R) 4
ESX, ESX 4.x
VMware(R) ESXi(TM) 5
ESXi, ESXi 5.x
Novell(R) SUSE(R) LINUX Enterprise Server 11 Service Pack 2
SLES11 SP2

viii
Notation
This manual uses the following fonts and symbols to express specific types of information.
Font or
symbol
Meaning
Example
italics
Title of a manual that you should refer to
See the PRIMEQUEST 1000 Series
Installation Manual (C122-E107EN).
[ ]
Window names as well as the names of
buttons, tabs, and drop-down menus in
windows are enclosed in brackets.
Click the [OK] button.
Notation for the CLI (command line interface)
The following notation is used for commands.
Command syntax
The following notation is used for commands.
- Variables requiring the entry of a value are enclosed in angle brackets < >.
- Optional elements are enclosed in brackets [ ].
- Options for optional keywords are grouped in | (stroke) separated lists enclosed in brackets [ ].
- Options for required keywords are grouped in | (stroke) separated lists enclosed in braces { }.
Command syntax is written in a box.
Remarks
The command output shown in the PDF manuals may include line feeds at places where there is no line feed
symbol (\ at the end of the line).
Notes on notations
- In this manual, the Management Board and MMB firmware are abbreviated as "MMB."
- In this manual, IOBs and GSPBs (LIOBs and LGSPBs within partitions) are collectively referred to as IO
Units.
- Screenshots contained in this manual may differ from the actual product screen displays.
- The IP addresses, configuration information, and other such information appearing in this manual are display
examples and differ from that displayed during actual operation.

ix
Alert messages
This manual uses the following alert messages to prevent users and bystanders from being injured and to
prevent property damage.
This indicates a hazardous (potentially dangerous) situation that is likely to result
in death or serious personal injury if the user does not perform the procedure
correctly.
This indicates a hazardous situation that could result in minor or moderate personal
injury if the user does not perform the procedure correctly. This also indicates that
damage to the product or other property may occur if the user does not perform the
procedure correctly.
This indicates information that could help the user use the product more
efficiently.
Alert messages in the text
An alert statement follows an alert symbol. An alert statement is indented on both ends to distinguish it from
regular text. Similarly, one space line is inserted before and after the alert statement.
Only Fujitsu certified service engineers should perform the following tasks on this
product and the options provided by Fujitsu. Customers must not perform these tasks
under any circumstances. Otherwise, electric shock, injury, or fire may result.
- Newly installing or moving equipment
- Removing the front, rear, and side covers
- Installing and removing built-in options
- Connecting and disconnecting external interface cables
- Maintenance (repair and periodic diagnosis and maintenance)
The List of important alert items tables list important alert items.
Product operating environment
This product is a computer intended for use in a computer room environment. For details on the product
operating environment, see the following manual:
PRIMEQUEST 1000 Series Hardware Installation Manual (C122-H004EN)

x
Notes
-If you have a comment or request regarding this manual, or if you find any part of this manual unclear, please
take a moment to share it with us by filling in the form at the following webpage, stating your points specifically,
and sending the form to us:
http://jp.fujitsu.com/platform/server/primequest/contact/
-The contents of this manual may be revised without prior notice.
The PDF file of this manual is intended for display using Adobe® Reader® in single page viewing mode at
100% zoom.
-The PRIMEQUEST 1800E2/1800E model supports only 200 V power supply.
Trademarks
- Microsoft, Windows, and Windows Server are trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries.
- Linux is a registered trademark of Linus Torvalds.
- Red Hat, the Shadowman logo and JBoss are registered trademarks of Red Hat, Inc. in the U.S. and other
countries.
- Intel and Xeon are trademarks or registered trademarks of Intel Corporation.
- Ethernet is a registered trademark of Fuji Xerox Co., Ltd. in Japan and is a registered trademark of Xerox
Corp. in the United States and other countries.
- VMware is a trademark or registered trademark of VMware, Inc. in the United States and other countries.
- Novell and SUSE Linux Enterprise Server are trademarks of Novell, Inc.
- Xen is a trademark or registered trademark of Citrix Systems, Inc. or its subsidiaries in the United States and
other countries.
- Other company names and product names are the trademarks or registered trademarks of their respective
owners.
- Trademark indications (TM, (R)) are omitted for some system and product names in this manual.

xi
Safety Precautions
List of important alert items
The following tables list the important alert items contained in this manual.
Only field engineers should perform the following tasks on this product and the options
provided by Fujitsu. Customers must not perform these tasks under any circumstances.
Otherwise, electric shock, injury, or fire may result.
Work
category
Warning
Location
Setup
- Newly installing or moving equipment
- Removing the front, rear, and side covers
- Installing and removing built-in options
- Connecting and disconnecting external interface cables
- Maintenance (repair and periodic diagnosis and maintenance)
CHAPTER 1
Configuring the
SAN Boot
Environment

xii
Warning labels
The following warning labels are affixed to this product. These labels are intended for the users of this product.
Never remove the warning labels.
* The label is affixed at either location.
Warning label location (PRIMEQUEST 1800E2/1800E rear)
Warning label location (PRIMEQUEST 1800E2/1800E rear) (IOBs removed)

xiii
Warning label location (PCI_Box)

xiv
Notes on Handling the Product
Adding optional products
For stable operation of the PRIMEQUEST 1000 series server, use only a Fujitsu certified optional product as an
added option.
Note that the PRIMEQUEST 1000 series server is not guaranteed to operate with any optional product not
certified by Fujitsu.
Maintenance
Only Fujitsu certified service engineers should perform the following tasks on this product and
the options provided by Fujitsu. Customers must not perform these tasks under any circumstances.
Otherwise, electric shock, injury, or fire may result.
- Newly installing or moving equipment
- Removing the front, rear, and side covers
- Installing and removing built-in options
- Connecting and disconnecting external interface cables
- Maintenance (repair and periodic diagnosis and maintenance)
Only Fujitsu certified service engineers should perform the following tasks on this product and
the options provided by Fujitsu. Customers must not perform these tasks under any circumstances.
Otherwise, product failure may result.
- Unpacking an optional Fujitsu product, such as an optional adapter, delivered to the customer
Modifying or recycling the product
Modifying this product or recycling a secondhand product by overhauling it without prior
approval may result in personal injury to users and/or bystanders or damage to the product and/or
other property.

xv
Note on erasing data from hard disks when disposing of the product or
transferring it
Disposing of this product or transferring it as is may enable third parties to access the data on the hard disk and
use it for unforeseen purposes. To prevent the leakage of confidential information and important data, all of the
data on the hard disk must be erased before disposal or transfer of the product.
However, it can be difficult to completely erase all of the data from the hard disk. Simply initializing
(reformatting) the hard disk or deleting files on the operating system is insufficient to erase the data, even
though the data appears at a glance to have been erased. This type of operation only makes it impossible to
access the data from the operating system. Malicious third parties can restore this data.
If you save your confidential information or other important data on the hard disk, you should completely erase
the data, instead of simply carrying out the aforementioned operation, to prevent the data from being restored.
To prevent important data on the hard disk from being leaked when the product is disposed of or transferred,
you will need to take care to erase all the data recorded on the hard disk on your own responsibility.
Furthermore, if a software license agreement restricts the transfer of the software (operating system and
application software) on the hard disk in the server or other product to a third party, transferring the product
without deleting the software from the hard disk may violate the agreement. Adequate verification from this
point of view is also necessary.
Support and Service
SupportDesk (available only in Japan, for a fee)
For stable system operation, we recommend concluding our SupportDesk agreement, which provides a
maintenance and operation support service. SupportDesk agreement customers receive a same-day
response service for hardware problems. They are eligible for regular checkups, remote notification of
potential-failure predictions, and information on system problems. Moreover, they can avail themselves of
other services such as troubleshooting support by phone for hardware and software problems, and access
to operation support information from a dedicated website for our customers. For details, see "Product
support" on the SupportDesk homepage
(http://jp.fujitsu.com/solutions/support/sdk/index.html).
Product and service inquiries
For all product use and technical inquiries, contact the store where you purchased the product, or a Fujitsu
sales representative or systems engineer (SE). If you do not know the appropriate contact address for
inquiries about the PRIMEQUEST 1000 series, use the Fujitsu contact line.

xvi
Fujitsu contact line
We accept Web inquiries. For details, visit our website:
https://www-s.fujitsu.com/global/contact/computing/PRMQST_feedback.html
Warranty
If a component failure occurs during the warranty period, we will repair it free of charge in accordance
with the terms of the warranty agreement. For details, see the warranty.
Before requesting a repair
If a problem occurs with the product, confirm the problem by referring to 11.2 Troubleshooting in the
PRIMEQUEST 1000 Series Administration Manual (C122-E108EN). If the error recurs, contact your sales
representative or a field engineer.
Confirm the model name and serial number shown on the label affixed to the right front of the device and
report it. Also check any other required items beforehand according to 11.2 Troubleshooting in the
PRIMEQUEST 1000 Series Administration Manual (C122-E108EN).
The system settings saved by the customer will be used during maintenance.

xvii
Revision History
Edition
Date
Revised location
(type) (*1)
Description
01
2011-02-01
All pages
(appropriated and
revised)
- Appropriated all the pages of APPENDIX D Configuring
the SAN Boot Environment from the PRIMEQUEST 1000
Series Installation Manual (C122-E107EN) and revised the
pages.
02
2011-05-31
All pages
- Added the procedure for setting UEFI driver version 4.12a7
or later.
04
2012-12-21
All pages
- Added descriptions about Windows Server 2012.
- Added descriptions about installing SLES11 SP2.
05
2013-09-17
Chapter 3
- Added the description about settings on the Converged
Network Adapter.
*1 Item numbers in the "Revised location" column refer to those in the latest edition of the document.
However, a number marked with an asterisk (*) denotes an item in a previous edition of the document.
This manual shall not be reproduced or copied without the permission of Fujitsu Limited.
Copyright 2010 - 2013 FUJITSU LIMITED

xviii
Contents
CHAPTER 1 Configuring the SAN Boot Environment ........................................................................1
1.1 Preparing to Configure the SAN Boot Environment ...................................................................1
1.2 SAN Boot Environment Configuration Flow ..............................................................................2
1.3 Notes on SAN Boot Environment Design ...................................................................................4
1.3.1 Notes on system design ...............................................................................................................4
1.3.2 Notes on system installation........................................................................................................4
1.3.3 Notes on system operation...........................................................................................................5
1.4 ETERNUS Connection Settings ..................................................................................................6
1.4.1 Settings for Windows ..............................................................................................................6
1.4.2 Settings for Linux ....................................................................................................................9
1.4.3 Settings for VMware ESX.....................................................................................................10
CHAPTER 2 Settings on the Fiber Channel Card (FC Card) .............................................................13
2.1 UEFI Driver Settings on the FC Card........................................................................................13
2.1.1 Selecting the method of making settings for the FC card (1) ....................................................14
2.1.2 Selecting the method of making settings for the FC card (2) ....................................................16
2.2 Procedure for Setting UEFI Driver Version 4.00a1 or Earlier on the FC Card .........................19
2.2.1 Displaying the driver list ...........................................................................................................19
2.2.2 Displaying the HBA list ............................................................................................................20
2.2.3 Starting the HBA setup utility ...................................................................................................22
2.2.4 Displaying the HBA setup utility ..............................................................................................23
2.2.5 Acquiring an HBA WWN .........................................................................................................24
2.2.6 Initializing the HBA setting.......................................................................................................25
2.2.7 Enabling BIOS...........................................................................................................................28
2.2.8 Speed and Topology settings.....................................................................................................30
2.2.9 Boot device setting ....................................................................................................................38
2.2.10 Applying settings.....................................................................................................................46
2.2.11 Recording the WWN of the FC port........................................................................................46
2.3 Procedure for Setting UEFI Driver Version 4.12a7 or Later on the FC Card............................48
2.3.1 Displaying the Device Manager ................................................................................................48
2.3.2 Starting the HBA setup utility ...................................................................................................49
2.3.3 Acquiring an HBA WWN .........................................................................................................51
2.3.4 Selecting an HBA ......................................................................................................................52
2.3.5 Initializing the HBA setting.......................................................................................................54

xix
2.3.6 Enabling BIOS...........................................................................................................................56
2.3.7 Speed and Topology settings.....................................................................................................58
2.3.8 Boot device setting ....................................................................................................................67
2.3.9 Applying settings.......................................................................................................................79
2.3.10 Recording the WWN of the FC port........................................................................................81
CHAPTER 3 Settings on the Converged Network Adapter................................................................83
3.1 UEFI Driver Settings on the Converged Network Adapter .........................................................83
3.2 Procedure for Setting UEFI Driver Version 5.01A13 or Later on the Converged Network
Adapter ......................................................................................................................................84
3.2.1 Displaying the Device Manager ............................................................................................84
3.2.2 Starting the HBA setup utility ...............................................................................................84
3.2.3 Acquiring an HBA WWN .....................................................................................................86
3.2.4 Selecting an HBA ..................................................................................................................86
3.2.5 Initializing the HBA setting...................................................................................................88
3.2.6 Enabling BIOS.......................................................................................................................90
3.2.7 Configuring the DCBX (Data Center Bridging Exchange) mode .........................................92
3.2.8 Configuring the converged network adapter and boot parameters ........................................94
3.2.9 Boot device setting ................................................................................................................95
3.2.10 Applying settings.............................................................................................................104
3.2.11 Recording the WWN of the FCoE port ...........................................................................106
CHAPTER 4 Installing Windows .....................................................................................................109
4.1 Installing Windows Server 2008/2012.....................................................................................109
4.1.1 Preparing for Windows Server 2008/2012 installation............................................................109
4.1.2 Installing the OS and bundled software...................................................................................113
4.1.3 Various post-installation settings.............................................................................................114
4.1.4 Advanced settings of driver parameters...................................................................................115
4.1.5 For a multipath configuration ..................................................................................................116
4.2 Installing Windows Server 2003 SP2 ......................................................................................117
4.2.1 Preparing to install Windows Server 2003 SP2.......................................................................117
4.2.2 Preparing for the FC card driver..............................................................................................117
4.2.3 Installing the OS and bundled software...................................................................................118
4.2.4 Installing HBAnyware.............................................................................................................121
4.2.5 Making various settings after installation................................................................................122
4.2.6 Advanced settings of driver parameters...................................................................................123
4.2.7 For a multipath configuration ..................................................................................................124
4.3 Changing and Checking the Setting of Detailed FC Card Information ...................................125