Fujitsu PRIMERGY TX200 S7 User guide

PRIMERGY TX200 S7
System configurator and order-information guide
Contents
Instructions
Configuration diagram
Configurator
0 System software
I Basic unit
II Processor
III Memory
IV Graphics
V Accessible drives
VI Hard disk drives
VII External SAS or SCSI Disk Array
VIII Internal Disk Array
IX Fiberchannel
X Communication/Network
XI System Management Products (RemoteView)
XII Miscellaneous
XIII Country specific power cord
Change report
PRIMERGY Server
February 2014

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III Memory, example
There are X memory slots which can be equipped with XXX MB
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB
Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x
Please note that there are information symbols which indicate necessary information.
Further information in the internet see:
http://ts.fujitsu.com/products/standard_servers/index.html (internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx
(extranet)
Prices and availability see price list and PC-/System-Architect.
Subject to change and errors excepted.
Fujitsu PRIMERGY Server 2 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
Configuration diagram PRIMERGY TX200 S7 SATA LFF (3.5") System Unit
System unit ( I )
SIDE VIEW FRONT VIEW
red. Fan / PSU Kit 3 x 5.25" bays available
1. PSU
standard 3 x HH 5.25" free or 2 x HH 5,25" free + Option A or
or Power 1 x HH 5,25" free + Option B or
2. PSU
Supply 0 x HH 5.25" free + Option C
(red. + hot plug)
Option A Option B Option C
std. PSU + std. Fans
1.6 * 5.25" 2x 1.6 * 5.25" 3x 1.6 * 5.25"
or
red. hp PSU + red. Fans
Depending on Base Unit
Processor ( II )
1st Xeon 4C, 6C or 8C
2nd Xeon 4C, 6C or 8C
CPU incl. Heatpipe CPU incl. Heatpipe
II / A II / B II / C II / D II / E II / F
Accessible drives ( V )
I / A I / B I / C I / D I / E I / F
Mounting Kit DVD(sl) + LSP/LSD: (Option A)
Memory ( III )
- support for SL (0.5") DVD Drive + LSD (Local Service Display)
each CPU offers 2 Banks ( I and II ) with 3 Channels each
- occupies one 5.25" bay
Channels D, E, F are only available if 2nd CPU is configured MtK DVD(sl) + LSP/LSD + 2x SAS/SATA LFF HDD: (Option B)
- support for 2x 3.5" SAS/SATA HDD hot plug
+ support for SL (0.5") DVD Drive + LSD (Local Service Display)
Extension slots
MtK DVD(sl) + 4x SAS/SATA LFF HDD: (Option C)
- support for 4x 3.5" SAS/SATA HDD hot plug
SAS Controller ( VII ) + support for SL (0.5") DVD Drive
Disk Array ( VIII )
Communication/Network ( IX )
Miscellaneous ( X ) Hard disk drives ( VI )
Slot 6 PCIe-3 x16,170 mm @ CPU2
this slot is only available with 2 CPUs implemented
Slot5 PCIe-3 x4, 280 mm @ CPU1
Possibility to install PCIe x8 cards; 1st pref. RAID Slot
Slot 4 PCIe-3 x16, 280 mm @ CPU1
Slot 3 PCIe-3 x4, 280 mm @ CPU1
Possibility to install PCIe x8 cards
Slot 2 PCIe-2 x4, 235 mm @ PCH
Possibility to install PCIe x8 cards; 2nd pref. RAID Slot
Slot 1 (5V): PCI 32-Bit/33MHz, 280mm @ PCH
Key:
Included in basic unit
Option
1.)
2.)
4.)
Fan 1
4x 3,5" HDD Frame
5.)
3.)
3x 120 mm Fans (no redundancy)
6.)
3.5"x1" SAS or SATA
3.5"x1" SAS or SATA
3.5"x1" SAS or SATA
3.5"x1" SAS or SATA
1.6 * 5.25"
Fan 3
Fan 2
4 port SAS Backplane
LSD Option
1.6 * 5.25"
Slim DVD
Fan4 for Redundancy
Slim DVD
Slim DVD
6 PCI-Busses
1.6 * 5.25"
LSD Option
not used
SAS / SATA
SAS / SATA
SAS / SATA
SAS / SATA
SAS / SATA
SAS / SATA
Fujitsu PRIMERGY Server 3 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
Configuration diagram PRIMERGY TX200 S7 SFF (2.5") System Unit
System unit ( I )
SIDE VIEW FRONT VIEW
red. Fan / PSU Kit 3 x 5.25" bays available
1. PSU
standard 3 x HH 5.25" free or
or Power 2 x HH 5.25" free + Option A or
2. PSU
Supply 1 x HH 5.25" free + Option D or
(red. + hot plug) 0 x HH 5.25" free + Option A + Option D
std. PSU + std. Fans
Option D
or 8x 2.5"
red. hp PSU + red. Fans
Depending on Base Unit
Option A Option A
Processor ( II ) 1.6 * 5.25" 1.6 * 5.25"
1st Xeon 4C, 6C or 8C
2nd Xeon 4C, 6C or 8C
CPU incl. Heatpipe CPU incl. Heatpipe
II / A II / B II / C II / D II / E II / F
Accessible drives ( V )
I / A I / B I / C I / D I / E I / F
Mounting Kit DVD(sl) + LSD: (Option A)
Memory ( III ) - support for SL (0.5") DVD Drive + LSD
each CPU offers 2 Banks ( I and II ) with 3 Channels each
- occupies one 5.25" bay
Channels D, E, F are only available if 2nd CPU is configured
optional SFF SAS/SATA HDD extension Box: (Option D)
- support for 8x 2.5" (SFF) SAS/SATA HDD hot plug
Extension slots
- occupies two 5.25" bays
SAS Controller ( VII )
Disk Array ( VIII )
Communication/Network ( IX )
Miscellaneous ( X ) Hard disk drives ( VI )
Slot 6 PCIe-3 x16,170 mm @ CPU2
this slot is only available with 2 CPUs implemented
Slot5 PCIe-3 x4, 280 mm @ CPU1
Possibility to install PCIe x8 cards; 1st pref. RAID Slot
Slot 4 PCIe-3 x16, 280 mm @ CPU1
Slot 3 PCIe-3 x4, 280 mm @ CPU1
Possibility to install PCIe x8 cards
Slot 2 PCIe-2 x4, 235 mm @ PCH
Possibility to install PCIe x8 cards; 2nd pref. RAID Slot
Slot 1 (5V): PCI 32-Bit/33MHz, 280mm @ PCH
Key:
Included in basic unit
Option
2.5" (SFF) SAS/SATA
Slim DVD
Slim DVD
1.6 * 5.25"
2.5" SAS/SATA
2.5" SAS/SATA
2.5" SAS/SATA
2.5" SAS/SATA
2.5" SAS/SATA
2.5" SAS/SATA
1.6 * 5.25"
Air - Channel
LSD Option
LSD Option
not used
Fan 1
3x 120 mm Fans (no redundancy)
Fan 3
8 port SAS Backplane
Fan 2
2.5" (SFF) SAS/SATA
2.5" (SFF) SAS/SATA
2.5" (SFF) SAS/SATA
8x SFF HDD Frame
2.5" (SFF) SAS/SATA
not used
2.5" (SFF) SAS/SATA
2.5" (SFF) SAS/SATA
2.5" (SFF) SAS/SATA
2.5" SAS/SATA
2.5" SAS/SATA
Air - Channel
1.)
Fan4 for Redundancy
6 PCI-Busses
2.)
6.)
5.)
4.)
3.)
Fujitsu PRIMERGY Server 4 of 28

System configurator and order-information guide
Start PRIMERGY TX200 S7
PRIMERGY TX200 S7 Status 2014-01-30
SW Configurator 64 bit (EM64T / IA64)
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
For all SW products please refer to the corresponding is not allowed to be ordered
software configurator accessible via the Extranet under
separately.
"Configuration & Tools, -All configurations, -Software, Exceptions: VMware SW,
URL see below. Citrix XenServer
VMware-Software
- VirtualCenter Management Server for any server released for Windows Server 2003
- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems
- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way
Citrix XenServer / Essentials for XenServer
- XenCenter Management Server for any server released for Windows 2000/XP/Vista and Server 2003/2008
XenServer editions released for PRIMERGY except all mono PRIMERGY systems (see release matrix for details)
Microsoft Hyper-V Server and System Center for SME
- Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2
- Microsoft System Center Essentials 2010 for any server released for Windows Server 2008 R2
- Microsoft Hyper-V Server 2008 R2 - Free Microsoft Web Download (not necessary for Windows Server 2008 R2 customers)
Microsoft - Windows Server 2008 R2 Server Licenses Microsoft - Windows Small Business Server 2011
- Windows HPC Server 2008 R2 Suite - Windows Small Business Server Standard 2011
-
Windows Server 2008 R2 Datacenter
- Windows Small Business Server 2011 Premium Add-on
- Windows Server 2008 R2 Enterprise
- Windows Small Business Server Essentials 2011
- Windows Server 2008 R2 Standard
- Windows Web Server 2008 R2 - Windows Small Business Server 2011 Standard I Premium Device CAL
- Windows Small Business Server 2011 Standard I Premium User CAL
- Windows Server 2008 Enterprise - Windows Server 2008 Remote Desktop Services Device CAL
- Windows Server 2008 Standard - Windows Server 2008 Remote Desktop Services User CAL
Microsoft - Windows Server 2008 Client Access Licenses
- Windows Server 2008 Device CAL
- Windows Server 2008 User CAL
- Windows Server 2008 Remote Desktop Services Device CAL Linux - Software *) **)
- Windows Server 2008 Remote Desktop Services User CAL # Open Enterprise Server ***)
only
- SuSE Linux ES (OEM): LO
EM64T - Red Hat EL (OEM): LO
QuickTransit (QT)
only
Transition Solaris Apps.
EM64T
to x86-64 PY with Linux
ServerView Resource Orchestrator VE*) ServerView Resource Orchestrator CE*)
Virtual Edition (ROR VE) Resource management Cloud Edition (ROR CE) Resource orchestration
Windows, Linux, Vmware, Solaris Server
Windows, Linux, VMware Server
for PRIMERGY BX/RX/TX, PRIMEQUEST, SPARC for PRIMERGY BX/RX/TX, PRIMEQUEST
only MultiPath, Duplex Data Details eg. version numbers are published
EM64T Manager (DDM) on the page referred to
Windows, Linux (W-DDM)
*) Please consult the ROR VE release and ordering information in the Extranet under
https://partners.ts.fujitsu.com/com/products/software/resco/Pages/default.aspx
Manageability Software: V**) *) Please consult the ROR CE release and ordering information in the Extranet under
- iRMC advanced Pack https://partners.ts.fujitsu.com/com/products/software/ror/Pages/default.aspx
only
- RemoteView Software
EM64T - RemoteView Service Board **) Pay attention to release and order information in PRINCE -> Operating System
- RemoteView Diagnosis https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
- RemoteDeploy ***) Supply over distribution or procurement from FSC VP BC Software
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
Continue with PRIMERGY
for partners:
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
HW configurator
Microsoft Windows Small Business Server 2011 Client Access
Licenses
Microsoft - Downgrade Media Only
Fujitsu PRIMERGY Server 5 of 28

System configurator and order-information guide
Start PRIMERGY TX200 S7
PRIMERGY TX200 S7 Status 2014-01-30
SW Configurator 64 bit (EM64T / IA64)
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
For all SW products please refer to the corresponding is not allowed to be ordered
software configurator accessible via the Extranet under separately.
"Configuration & Tools, -All configurations, -Software, Exceptions: VMware SW,
URL see below. Citrix XenServer
VMware-Software
- VirtualCenter Management Server for any server released for Windows Server 2003
- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems
- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way
Citrix XenServer / Essentials for XenServer
- XenCenter Management Server for any server released for Windows 2000/XP/Vista and Server 2003/2008
- XenServer and Essentials for XenServer released for RX200S5, RX300S4/S5, RX600S4, BX620S4/S5, BX920S1
Microsoft Hyper-V Server and System Center for SME
- Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2
- Microsoft System Center Essentials 2010 for any server released for Windows Server 2008 R2
- Microsoft Hyper-V Server 2008 R2 - Free Microsoft Web Download (not necessary for Windows Server 2008 R2 customers)
as soon as available
Microsoft - Windows Server 2008 R2 Server Licenses
Microsoft - Windows Small Business Server 2011
-
Windows HPC Server 2008 R2 Suite
- Windows Small Business Server Standard 2011
- Windows Server 2008 R2 Datacenter - Windows Small Business Server 2011 Premium Add-on
-
Windows Server 2008 R2 Enterprise
- Windows Server 2008 R2 Standard as soon as available
- Windows Web Server 2008 R2 - Windows Small Business Server 2011 Standard I Premium Device CAL
- Windows Small Business Server 2011 Standard I Premium User CAL
- Windows Server 2008 Enterprise - Windows Server 2008 Remote Desktop Services Device CAL
- Windows Server 2008 Standard - Windows Server 2008 Remote Desktop Services User CAL
Microsoft - Windows Server 2008 Client Access Licenses
- Windows Server 2008 Device CAL
- Windows Server 2008 User CAL
- Windows Server 2008 Remote Desktop Services Device CAL Linux - Software *) **)
- Windows Server 2008 Remote Desktop Services User CAL #
Open Enterprise Server ***)
only - SuSE Linux ES (OEM): LO
EM64T - Red Hat EL (OEM): LO
PRIMECLUSTER *)
- Clustering
- Load Balancing
QuickTransit (QT)
only Transition Solaris Apps.
EM64T
to x86-64 PY with Linux
only
MultiPath, Duplex Data
Details eg. version numbers are published
EM64T Manager (DDM) on the page referred to
Windows, Linux (W-DDM)
*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx
Manageability Software: V**)
- iRMC advanced Pack **) Pay attention to release and order information in PRINCE -> Operating System
only
- RemoteView Software
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
EM64T - RemoteView Service Board
- RemoteView Diagnosis
***) Supply over distribution or procurement from FSC VP BC Software
- RemoteDeploy
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users:
http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
Continue with PRIMERGY
for partners: https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
HW configurator
Microsoft Windows Small Business Server 2011 Client Access
Microsoft - Downgrade Media Only
Fujitsu PRIMERGY Server 6 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
Section
IBasic unit
System unit, Rack and Floorstand, including:
* Two lockable front covers in floorstand version
Door #1 for accessible drive bays
Door #2 for hot plug HDD bays
Both doors may be locked or door #1 may be left open while door #2 is still locked
* backplane with 4 (LFF) or 8 (SFF) bays for hot-plug HD's. Type depending on base unit:
Type 1: 4x hot plug LFF (3.5") SAS/SATA HDD (SAS/SATA LFF base units only)
Type 2: 8x (2x4) hot plug SFF (2.5") SAS HDD (SAS SFF base units only)
* PSU and Fan Type depending on base unit:
Type 1: standard PSU and standard Fans (3 System Fans)
(V101and V301, V501 and V701 base units)
Type 2: without PSU (450W or 800W must be added), but 1 additional fan for redundancy
(V201, V401, V601 and V801 base units)
for Type 1 base units there is an upgrade to
hot plug redundant PSU and redundant Fans available
* 3 bays 5.25" for accessible drives (half Hight)
Systemboard D3099 with:
* Up to two Xeon 4C, 6C & 8C CPU`s (Socket-B2)
with 1 serial QPI link ( Quick Path Interconnect ) and 3 memory channels per CPU
First CPU has to be selected for an orderable basic unit,
* Chipset Intel® C600 Series (codenamed Patsburg)
* 6 PCI slots: - 2x PCIe-3 x16
- 2x PCIe-3 x4 (mechanically x8)
- 1x PCIe-2 x4 (mechanically x8)
- 1x PCI 32/33
- No mix of registered and unbuffered modules is allowed
- First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible module wise for the Independent Channel Mode or
for the Performance Mode,
- Memory mirrroring is supported with 2 identical modules in channel B+C CPU 1 or E+F CPU 2
- Hot Spare Memory is supported with 3 identical modules in channel A+B+C CPU 1 or D+E+F CPU 2
- SDDC (Chipkill) is supported only for registered memory modules,
* 6-port SATA controller on-board included in Intel Southbridge Patsburg A for SATA Raid0/1,
optional Southbridge Patsburg B with 4 ports for SAS RAID 0/1
Max. 4 SATA / SAS HD`s are supported
Max. 2 SATA accessible drives are supported (DVD, Backup)
* 2x1 Gbit Ethernet LAN on board ( Intel Hartwell);
iSCSI boot integrated in System BIOS as selectable option
* iRMC S3 (integrated Remote Management Controller) on-board server management controller
with dedicated 10/100 Service LAN-port and
integrated graphics controller ( max. Resolution: 1600 x 1200 at 16 bpp)
The Service LAN-port can be switched alternatively on standard Gbit LAN port
Interfaces:
* 1x RS-232-C (serial, 9pin) (usable for BMC or OS or shared)
* 1x VGA (15 pin)
* 9x USB 2.0 (UHCI ) with 480MBit/s (4x external at the rear, 2x external at the frontside, 3x internal for backup or UFM)
* 2x LAN RJ45, 1x Service-LAN RJ45
*internal Cables:
1. SATA cable for CD/DVD.
2. Cable for HDD Backplane
3. USB cable (if USB Backup is used)
* ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates
* Documentation engl. (multilingual on CD)
A
Start PRIMERGY TX200 S7
Fujitsu PRIMERGY Server 7 of 28

System configurator and order-information guide
A
PRIMERGY TX200 S7 Status 2014-01-30
Floorstand System Rack System
without CPU, Memory and hot plug PSU without CPU, Memory and hot plug PSU - No Rackmount Kit included !
- One CPU ( first CPU ) has to be configured
- One CPU ( first CPU ) has to be configured - The Rackmount Kit or the
additionally for a base configuration additionally for a base configuration option no Rackmount Kit has
- One memory kit per CPU has to be
- One memory kit per CPU has to be
to be ordered separately
configured for a base configuration configured for a base configuration
LFF Base Unit standard S26361-K1404-V101 LFF Base Unit standard S26361-K1404-V501
- 3 std fans and std PSU - 3 std fans and std PSU
- 4-port SAS backplane for 4x 3.5" hot plug SAS
- 4-port SAS backplane for 4x 3.5" hot plug SAS
or SATA HD`s incl. cables for connection to the or SATA HD`s incl. cables for connection to the
modular or onboard controllers
modular or onboard controllers
LFF Base Unit redundant S26361-K1404-V201 LFF Base Unit redundant S26361-K1404-V601
- 3 std fans plus 1 std fan for redundancy - 3 std fans plus 1 std fan for redundancy
- 1 hp PSU has to be added - 1 hp PSU has to be added
- 4-port SAS backplane for 4x 3.5" hot plug SAS
- 4-port SAS backplane for 4x 3.5" hot plug SAS
or SATA HD`s incl. cables for connection to the or SATA HD`s incl. cables for connection to the
modular or onboard controllers
modular or onboard controllers
SFF Base Unit standard S26361-K1404-V301 SFF Base Unit standard S26361-K1404-V701
- 3 std fans and std PSU - 3 std fans and std PSU
- 8-port SAS backplane for 8x 2.5" hot plug SAS
- 8-port SAS backplane for 8x 2.5" hot plug SAS
or SATA HD`s incl. cables for connection to the or SATA HD`s incl. cables for connection to the
modular or onboard controllers
modular or onboard controllers
SFF Base Unit redundant S26361-K1404-V401 SFF Base Unit redundant S26361-K1404-V801
- 3 std fans plus 1 std fan for redundancy - 3 std fans plus 1 std fan for redundancy
- 1 hp PSU has to be added - 1 hp PSU has to be added
- 8-port SAS backplane for 8x 2.5" hot plug SAS
- 8-port SAS backplane for 8x 2.5" hot plug SAS
or SATA HD`s incl. cables for connection to the or SATA HD`s incl. cables for connection to the
modular or onboard controllers
modular or onboard controllers
Cables included in basic unit
Cable for CD/DVD is included
All cables for connection of HDD Backplane are included
Cables for USB Backup Drives are automatically provided
if a USB Backup Drive is ordered.
S26361-F3552-E1
S26361-F3552-E1 Only 1 TPM per system.
TPM Module TPM Module Loose delivery for later
Trusted Platform Module on Motherboard
Trusted Platform Module on Motherboard integration possible.
Use according to import restrictions Use according to import restrictions
for customer
max. 1x per system max. 1x per system
S26361-F3552-L1
TPM Module add-on kit
C B for later integration (loose delivery)
Trusted Platform Module on Motherboard
Use according to import restrictions
max. 1x per system
Fujitsu PRIMERGY Server 8 of 28

B
System configurator and order-information guide
PRIMECENTER Rack
PRIMERGY TX200 S7 Status 2014-01-30
S26361-F2735-E285 S26361-F2735-E111 Rack Mount Kit F2-C S7 LV
RMK-F2_DI_CMA_QRL_LV
No Rackmount-Kit option
length variable (559mm- 860mm)
telescopic drop-in rail, full extr.
Only for loose deliveries
for loose delivery
1-hand-mounting
No mounting in racks possible with CMA adapter
RMK - 1 pair consisting of max. 1x per system S26361-F2735-L285
-
vario carrier length variable without CMA adapter
with quick release lever support S26361-F2735-L286
- telescopic drop-in rails
with CMA adapter Sideways cable management arm
1x per system Cfor mounting in asymmetrical FJ racks.
Has to be mounted above the RMK.
S26361-F2735-L7
S26361-F4530-E12 S26361-F4530-E10 Support bracket 3U S26361-F2735-L31
Mounting systems higher 3U in Mounting in
has to be ordered for loose delivery
asymmetrical racks
symmetrical racks
S26361-F2735-L31
with 3U support bracket
(no support bracket needed)
S26361-F2735-E71
S26361-F2735-E82
Cable Management Arm (CMA) can
Lateral cable management 2U cable management arm (CMA) only be used for FTS RMKs with
for 2U servers or higher
for 2U server or higher CMA adapter
- for asymmetrical racks - for symmetrical racks
PRIMECENTER S2 or M1 M1 or 3rd party racks S26361-F2735-L82
- 1 bracket PC Rack asym. Fujitsu racks Cable management arm for 2U Server
1x per system 1x per system
or higher for loose delivery
can only be mounted at RMK with
CMA adapter
for loose delivery
SNP:SY-F1647E301-P
Installation ex works for one
server or subsystem.
Hereby the rack will be delivered "Rack-mounting ex factory"
completely pre-mounted and This service is to be ordered once
all wired connections are tested. per installable server/storage
With PCR S2 12U, 24U, 38U and subsystem, in order to get the
PRC M1 16U, 24U, 42U: server/storage subsystem
Systems and components mounted into the racks.
will be delivered installed in the rack
In case of the 46 U PCR S2
With PCR S2 racks 46U: this service has to be ordered,
Systems and components to get the mounting kits and the
will be delivered separately
cables installed.
To be ordered only together with
a PRIMECENTER rack
PCR S2 e.g. S26361-K826-V10x
new PCR M1 e.g. S26361-K827-Vxxx
refer PCR S2 or M1 rack configurator
max. 1x per System
PRIMERGY Classic 19" rack is not supported
For later conversion the following kits are available:
1.) Conversion kit 2 Floor -> Rack S26361-F1729-L260
Conversion PRIMERGY TX200 S7 base unit floorstand into
base unit rack. Only conversion, no mounting kit.
Mounting kit has to be ordered seperatly.
C
Fujitsu PRIMERGY Server 9 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
C
1x mandatory for redundant base units
there is only 1 PSU type allowed (450W or 800W)
*For order completeness only
Will be added automaticly with
S26113-F575-E10 S26113-F574-E10 System Architect Version ≥ V9.3
2x Power supply 450W Power supply 800W
(hot plug) (hot plug)
For redundant Base Units only
occupies one bay for occupies one bay for
(V201, V401, V601 and V801)
hot plug power supply
hot plug power supply
max. 2x per system
max. 2x per system
For redundant floorstand versions only
(V201 and V401)
A second, redundant power supply requires an additional
country specific power cord (section XIII)
For later upgrades the following kits are available:
1 power supply module 450W hot plug: S26113-F575-L10
Supplementary module
1 power supply module 800W hot plug: S26113-F574-L10
Supplementary module
Attention: There is no power cable included!
Std to Redundant Upgrade Kit
S26361-F3699-L1
consisting of a redundant PSU cage and backplane
AND a 4th fan for fan redundancy
Does not contain any PSU module
Section
II Processor
There are 2 processor sockets available.
The first socket is always equipped with the first CPU which can be selected via configurator
It is also possible to upgrade a dual-processor system later on with a second CPU
Two processors with different clock frequencies are not possible
A multi-processor operating system is required for a dual-processor system.
Max. two CPU`s can be selected per basic unit
Note: Max. DDR3 Bus Speed depends on:
One of following CPU´s has to be selected as first CPU
- max. DDR3 Bus Speed from the CPU and
for an orderable basic unit
- max. DDR3 Memory Speed and
Optional second CPU has to be the same type like the first CPU - max. memory modules on one memory channel
Basic 4C CPU's
- 1x 64-bit Intel Xeon (10MB shared TLC = Third Level Cache )
1066 MHz DDR3 Bus, 6,40 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2403 4C/4T 1.80GHz 10MB 6.40GT/s 1066MHz 80W
S26361-F3684-E180
Xeon E5-2407 4C/4T 2.20GHz 10MB 6.40GT/s 1066MHz 80W
S26361-F3684-E220
Standard Turbo 6C CPU's
- 1x 64-bit Intel Xeon (15MB shared TLC = Third Level Cache ); Hyper-Threading (HT);
1333 MHz DDR3 Bus, 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2420 6C/12T 1.90GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3723-E190
Xeon E5-2430 6C/12T 2.20GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3723-E220
Xeon E5-2440 6C/12T 2.40GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3723-E240
Advanced Turbo+ 8C CPU
- 1x 64-bit Intel Xeon (20MB shared TLC = Third Level Cache ); Hyper-Threading (HT);
1600 MHz DDR3 Bus, 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2450 8C/16T 2.10GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3724-E210
Xeon E5-2470 8C/16T 2.30GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3724-E230
Low Power 6C CPU
- 1x 64-bit Intel Xeon (15MB shared TLC = Third Level Cache ); Hyper-Threading (HT);
1333 MHz DDR3 Bus, 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2430L 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 60W S26361-F3725-E200
D
Fujitsu PRIMERGY Server 10 of 28

System configurator and order-information guide
D
PRIMERGY TX200 S7 Status 2014-01-30
Section
III Memory
- There are 6 memory slots per CPU for max.
96GB RDIMM (6x 16GB 2R)
24GB UDIMM (6x 4GB)
=> max. 192GB for two CPU`s ( 96GB per CPU ), using RDIMM
- The memory area is divided into 3 channels per CPU with 2 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2.
Registered and unbuffered memory modules can be selected
No mix of registered and unbuffered modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed).
In a 2 DIMMs per channel configuration, following frequencies are supported:
- 1.5V - 1600MHz max (depending on CPU, special memory modules)
- 1.35V - 1333MHz max (depending on CPU)
SDDC (Chipkill) is supported for registered x4 organized memory modules only
1.) In the "Independent Channel Mode" is following configuration possible
Channels can be populated in any order in Independent Channel Mode. All 3
channels may be populated in any order and have no matching requirements. All
channels must run at the same interface frequency but individual channels may run at
different DIMM timings (RAS latency, CAS latency, and so forth)
No mix of registered and unbuffered modules allowed.
2.) "Rank Sparing Mode" configuration
- Within a memorychannel, one rank is a spare of the other ranks.
The Spare Rank is held in reserve and is not available as system memory
For the effective memory capacity, please refer to the spreadsheet below.
The BIOS is set to the rank sparing setting.
Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel
This mode is not supported by x8 organized memory modules
3.) "Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 3x identical modules
4.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 2x registered memory modules
In each memory bank channel B and C of CPU 1 or channel E and F of CPU 2 have to be
equipped with identical modules for mirrored channel mode.
In channel C is always the mirrored memory of channel B of CPU 1
In channel F is always the mirrored memory of channel E of CPU 2
Minimum configuration is: 2x identical modules
This mode is not supported by x8 organized memory modules
D1
Fujitsu PRIMERGY Server 11 of 28

System configurator and order-information guide
D1
PRIMERGY TX200 S7 Status 2014-01-30
S26361-F3694-E10
Independent Mode
Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined
Requires min 1 memory Module per CPU
S26361-F3695-E1 Rank Sparing Mode Installation
BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shown in System Memory.
For effective capacity within a channel, please have a look below.
Supported for RDIMM only.
1x per CPU Requires min 2x 1R/2R or 1x 4R modules per CPU
S26361-F3695-E2 Performance Mode Installation
BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. 3 identical memory modules
will be equipped in one memory bank to achieve highest memory performance. All 3 modules are active and full capacity can be used.
Multiple of 3 identical modules to be configured per CPU
S26361-F3695-E3
Mirrored Channel Mode Installation
BIOS Setup factory preinstalled to this mode. 2 identical memory modules are always equipped in one memory bank to use the
Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data
Supported for RDIMM only.
Multiple of 2 identical modules to be configured per CPU
1R
2R
1R
2R
na na na na na
na na
Minimum one memory module or order code per CPU = first memory
Note 1.)
Unbuffered Memory (UDIMM) no SDDC (chipkill) support
Max. DDR3 memory speed depends on the memory configuration
- one DDR3 unbuffered ECC mem. Module, 1.35V (No of mem modules per channe) as well as on the CPU type.
Choose up to 6 order codes per CPU The memory channel with the lowest speed defines the speed
of all CPU channels in the system, also for the channels of the
2GB (1x2GB) 1Rx8 L DDR3-1600 U ECC S26361-F3694-E513 second CPU if configured.
6x per 4GB (1x4GB) 2Rx8 L DDR3-1600 U ECC S26361-F3694-E514 For real memoryspeed (depending on memory type / population),
CPU, max. Registered Memory (RDIMM) with SDDC (chipkill) support
2 modules
- one DDR3 registered ECC mem. Module, 1.35V
per channel 1600MHz supported with up to 2DPC (8 modules/CPU)
at 1.5V Mix of memory modules is only possible within the same group
Choose up to 6 order codes per CPU
4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC S26361-F3697-E514
8GB (1x8GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E515
16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E516
H
Effective Memory capacity / Rank Sparing Mode, 1 Channel populated
UDIMM
RDIMM
2GB
2GB
4GB
8GB
2R
16GB
1DPC
2DPC
4GB
12GB
24GB
Fujitsu PRIMERGY Server 12 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
Memory Configuration PRIMERGY TX200 S7
Each CPU offers 6 Slots for DDR3 Memory Modules organised in 2 Banks and 3 Channels.
If you need more than 6 Slots you have to configure the 2nd CPU.
Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below).
There are 2 different kinds of DDR3 Memory Modules available: UDIMM and RDIMM
UDIMM / RDIMM offer different functionality. Mix of UDIMM / RDIMM is not alloved.
If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V
Mode Configuration Application
SDDC (chipkill) support any no no yes detect multi-bit errors
Independant Channel 1, 2 or 3 Modules per Bank yes yes yes offers max. flexibility, upgradeability, capacity
Mode
use UDIMM modules for lowest cost
Mirrored Channel Mode *)
2 identical Modules / Bank
no no yes offers maximum security
Performance Mode
3 identical Modules / Bank
yes yes yes
offers maximum performance and capacity
Rank Sparing Mode *)
min. 2 Ranks / Channel no no yes balances security and capacity
*) For the delivery ex works the system will be prepared with dedicated BIOS setting.
Capacity Configuration UDIMM RDIMM Notes
Min. Memory per CPU
1 Module / CPU
1x2GB 1x4GB
with one CPU
Max. Memory per CPU 4/6 Modules / CPU 6x4GB
6x16GB
with one CPU
Max. Memory per System
8/12 Modules / System
48GB 96GB if second CPU is configured
Memory-Speed:
Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU
The memory channel with the lowest speed defines the speed of all CPU channels in the system
Voltage setting (BIOS)
DPC DPC DPC DPC DPC DPC DPC DPC DPC
CPU with 1600MHz DDR3 Bus
CPU with 1333MHz DDR3 Bus
CPU with 1066MHz DDR3 Bus
1R - Single Rank
2R - Dual Rank
1DPC = 1 DIMM per Channel
2DPC = 2 DIMM per Channel
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I black sockets
Bank II blue sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1/2 up to 3 memory modules connected to Channel A - F on the 1st/2nd CPU
Bank II on CPU 1/2 up to 3 memory modules connected to Channel A - F on the 1st/2nd CPU
- See below and next page for a detailed descriptions of the memory configuration supported.
1.5V [default]
1.35V
1.5V [default]
1.35V
UDIMM
RDIMM
RDIMM
Mem. Speed provided
by CPU
UDIMM 1600MHz
RDIMM 1600MHz
Real maximum memory-bus speed depending on CPU type,
memory configuration (DPC) and voltage setting (BIOS)
2
x8
x8
x4
1066
1066
1
2
1
2
1
2
3
-
1333
1333
1333
1
1333
1333
-
1333
1333
1600
1600
1333
1333
1333
1066
1066
1066
1066
1066
1066
1066
1066
-
1066
1066
Fujitsu PRIMERGY Server 13 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
1. Independent Channel Mode
required
required if 2nd CPU is configured
Bank I Data
Data
Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data
Data
Data Data Data Data optional, any type
(blue sockets)
Independent Channel Mode allows all channels to be populated in any order
Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system
2. Mirrored Channel Mode
required
required if 2nd CPU is configured
Bank I ------ Data Mirror ------ Data Mirror optional, same type in Bank per CPU
(black sockets)
Bank II ------ Data Mirror ------ Data Mirror ------ not used
(blue sockets)
Mirrored Channel Mode requires identical modules on channel B / C (1st CPU) or channel E / F (2nd CPU)
50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory
If this mode is used, a multiple of 2 identical modules has to be ordered.
3. Performance Channel Mode
required
required if 2nd CPU is configured
Bank I Data
Data
Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data
Data
Data Data Data Data optional, any type
(blue sockets)
Performance Channel Mode requires identical modules on all channels of each Bank per CPU.
If this mode is used, a multiple of 3 identical modules has to be ordered.
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8 Core)
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Fujitsu PRIMERGY Server 14 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
4. Rank Sparing Mode
required
required if 2nd CPU is configured
Bank I Spare Spare Spare Spare Spare Spare optional, same type in Channel per CPU
(black sockets)
Bank II Data Data Data Data Data Data optional, any type
(blue sockets)
Bank I R1 Spare Spare Spare Spare Spare Spare required
(black) R2 Data Data Data Data Data Data
required if 2nd CPU is configured
Bank II R1 Data Data Data Data Spare Spare
(blue) R2 Data Data Data Data Data Data optional, same type in Channel per CPU
Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel.
The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above
"Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max.
available memory.
1-Rank Memory modules (RDIMM)
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
2-Rank Memory modules (RDIMM)
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Fujitsu PRIMERGY Server 15 of 28

System configurator and order-information guide
H
PRIMERGY TX200 S7 Status 2014-01-30
Section
IV
Grafik
S26361-F2748-E537
PY VGA card 512MB PCI-e x1
NVIDIA NVS300
The hight end optional NVIDIA NVS300 graphic card offers dual head operation
512 MB PCIe-x1
and fully3D video support. The cables for either two times
Connectors: 1x LFH 59
DVI-I or VGA (cable kit) connections are part of the delievery.
cable kit for 2x DVI or 2x VGA Remote Video direction via iRMC must be disabled.
cable kits included This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot.
Dual head + professional 2-D + 3-D
Only one card per server is allowed.
supported for Windows OS
native driver support for Linux OS
S26361-F2748-L537
full height bracket PY VGA card 512MB PCI-e x1
max. 1x per system for loose delivery
Section VAccessible drives
There are 3 bays (1.6" x 5.25") for accessible drives usable for all or for LFF related base units.
For all SFF base units there is an additional bay; please refer to section VI hard disk drives SFF HDDs
see Conf. Diagram Option A see Conf. Diagram Option B see Conf. Diagram Option C
occupies 1 accessible bay occupies 2 accessible bays occupies all 3 bays
for all base units
only 3.5" HDD base units
only 3.5" HDD base units
S26361-F2826-E205
S26361-F2826-E106
S26361-F2826-E436
Mounting Kit DVD(sl) + LSP/LSD Mounting Kit DVD(sl) + Mounting Kit DVD(sl) +
Occupies one 5.25" x 1.6" bay LSP/LSD + SAS LFF HDD SAS LFF HDD
in the accessible bay area
Occ. two 5.25" x 1.6" bays
Occupies all 5.25" x 1.6" bays
Offers bays for: in the accessible bay area in the accessible bay area
- 1x Local Sv. Display option Offers bays for: Offers bays for:
- 1x 0.5 * 5.25" SATA DVD
- 1x Local Sv. Display option - 1x 0.5 * 5.25" SATA DVD
max. 1x per system
- 1x 0.5 * 5.25" SATA DVD - 4x 3.5" SAS/SATA HDD's
- 2x 3.5" SAS/SATA HDD`s Two 1 * 3,25" satin black bezels
One 0.5 * 3.5" satin black bezel
for SAS HDD bays
for Local Sv. Display bay max. 1x per system
One 0.5 * 5.25" satin black bezel
for 0.5 * 5.25" DVD bay
Two 1 * 3,25" satin black bezels
for SAS HDD bays
max. 1 per system
For the mounting kits Option B or C
S26361-F2826-E106 or -E436
a PCI based modular RAID
controller is necessary!
see Section VIII!
S26361-F2557-E105
S26361-F2557-E106
Local Service Display incl. Adapter
Local Service Display incl. Install. kit
Customer Self Service Customer Self Service
LSD module incl. adapter
LSD module incl. mounting kit
0.5" x 5.25" 0.5" x 5.25"
max. 1x per System max. 1x per system
S26361-F3269-E2 S26361-F3641-E2
DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA
all formats, DUAL/DL, DVD-RAM 6x BD-RW, 8x DVD, 24x CD
only W2K, W3K and Linux BD DL and all CD/DVD formats
0.5 x 5.25", black bezel
0.5 x 5.25"
max. 1x per system max. 1x per system
S26361-F3266-E2 S26361-F3267-E2 S26361-F3641-E4
DVD-ROM HH SATA
DVD-RW supermulti HH SATA Blu-ray Triple Writer slim SATA
16x DVD 48x CD all formats, DUAL/DL, DVD-RAM 4x BD-RW, 16x DVD, 40x CD
only W2K, W3K and Linux BD DL and all CD/DVD formats
1.6 x 5.25", black bezel
1.6 x 5.25", black bezel
1.6 x 5.25", black bezel
max. 1x per system max. 1x per system 0.5" drive with mounting frame
max. 1x per system
I
Fujitsu PRIMERGY Server 16 of 28

System configurator and order-information guide
I
PRIMERGY TX200 S7 Status 2014-01-30
S26361-F3325-E4
Tape drive DDS Gen6 USB 5.25"
80GB, 6MB/s, USB 2.0
data cartridges must be ordered
Connector: USB "B"
separately
with USB cable
incl. cleaning cartridge
without data cartridge
1.6 * 5.25", black bezel
max. 1x per system
S26361-F3749-E1 The adapter is also available as optional (loose) delivery
USB3.0 PCIe x1 adapter card with FH and LP bracket included
Sunrich U-720 S26361-F3749-L501
PCIe x1
1 port intern, 1 port extern
USB 3.0 A jacks
max. 1x per system
S26361-F3750-E4
RDX Drive USB3.0 5.25" internal RDX cartridges must be ordered separately
100MB/s, USB 3.0 RDX 320GB = S26361-F3857-L320
Connector: USB 3.0 "B" RDX 500GB = S26361-F3857-L500
with USB cable RDX 1TB = S26361-F3857-L600
without RDX cartridges
10x RDX320 = S26361-F3857-L329
1.6 * 5.25", black bezel
max. 1x per system
additional RDXcartridges can be ordered
S26361-F3750-E324 RDX 320GB = S26361-F3857-L320
RDX 320 5.25" RDX 500GB = S26361-F3857-L500
100MB/s, USB 3.0 RDX 1TB = S26361-F3857-L600
Connector: USB 3.0 "B"
10x RDX320 = S26361-F3857-L329
with USB3.0 cable
with 320GB RDX cartridge The bundle is also available as optional (loose) delivery
1.6 * 5.25", black bezel S26361-F3750-L324 with USB3.0 cable for adapter card.
max. 1x per system
The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
additional RDXcartridges can be ordered
S26361-F3750-E504 RDX 320GB = S26361-F3857-L320
RDX 500 5.25" RDX 500GB = S26361-F3857-L500
100MB/s, USB 3.0 RDX 1TB = S26361-F3857-L600
Connector: USB 3.0 "B"
10x RDX320 = S26361-F3857-L329
with USB3.0 cable
with 500GB RDX cartridge The bundle is also available as optional (loose) delivery
1.6 * 5.25", black bezel S26361-F3750-L504 with USB3.0 cable for adapter card.
max. 1x per system
The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
additional RDXcartridges can be ordered
S26361-F3750-E604 RDX 320GB = S26361-F3857-L320
RDX 1000 5.25" RDX 500GB = S26361-F3857-L500
100MB/s, USB 3.0 RDX 1TB = S26361-F3857-L600
Connector: USB 3.0 "B"
10x RDX320 = S26361-F3857-L329
with USB3.0 cable
with 1TB RDX cartridge
The bundle is also available as optional (loose) delivery
1.6 * 5.25", black bezel S26361-F3750-L604 with USB3.0 cable for adapter card.
max. 1x per system
The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
For internal SAS Backup drives
the onboard 4-port SAS controller "Patsburg B" has to be configured
Patsburg B is not available for SLES10!
I1
USB 3.0 adapter and RDX USB3.0 drive
Fujitsu PRIMERGY Server 17 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
I1
SAS Controller for internal Backup Drives
S26361-F3674-E1
Onboard 4 port SAS Controller
LSI
Patsburg B
1x RAID 0, 1 & 10
no controller cache
SAS 6Gb/sec
4 internal ports
PCIe x4
no PCI slot required
max. 1x per system
as soon as available
S26361-F3561-E4 S26361-F3626-E2 S26361-F3627-E1 S26361-F3787-E1
Tape drive LTO3HH Ultrium SAS
Tape drive LTO4 HH SAS IBM V2
Tape drive LTO5HH Ultrium SAS Tape drive LTO6HH Ultrium SAS
400GB, 60MB/s, SAS 3Gb 800GB, 120MB/s, SAS 6Gb 1500GB, 140MB/s, SAS 6Gb
2500GB, 160MB/s, SAS 6Gb
1x
Connector: mini-SAS
Connector: mini-SAS
Connector: mini-SAS
Connector: mini-SAS
incl. SAS cable incl. SAS cable incl. SAS cable incl. SAS cable
incl. cleaning cartridge incl. cleaning cartridge incl. cleaning cartridge incl. cleaning cartridge
without data cartridge without data cartridge without data cartridge without data cartridge
1.6 * 5.25", black bezel 1.6 * 5.25" 1.6 * 5.25" 1.6 * 5.25"
max. 1x per system max. 1x per system max. 1x per system max. 1x per system
Controller depends on I/O-Module
IOM available: - SAS/SATA; - USB
J
Fujitsu PRIMERGY Server 18 of 28

JSystem configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
Section
VI
Hard disks drives
SAS RAID Controller for up to 4 SAS HDDs
S26361-F3674-E1
Onboard 4 port SAS Controller
If the onboard 4 port SATA or SAS Controller is used for HDD,
LSI
it is not possible to implement a LTO drive later
Patsburg B replaces 4 onb. SATA ports
RAID 0, 1 & 10
no controller cache
SAS 6Gb/sec
4 internal ports
PCIe x4
no PCI slot required
max. 1x per system
3.5" HDDs for LFF base units; SAS or more than 4 SATA HDDs require a RAID Controller! See section VIII internal Disk Array
Up to 4 LFF (3.5") hard disks can be configured into the base unit
With the HDD Extension Box Option B up to 6 LFF (3.5") hard disks can be configured, with Option C up to 8 HDDs.
The on board SATA Controller can be used with up to 4x 3.5" SATA HDDs (no additional controller required), BUT:
If a LTO backup drive is configured, then the 4 onboard SATA ports for HDDs are not available!
In this case for any HDD solution a PCI based 8port RAID controller is necessary!
For up to 4x 3.5" SAS HDDs without SAS Tape a Patsburg SAS RAID controller is available
For up to 4x 3,5" SAS HDDs in combination with a SAS tape or fr all other HDD configurations a 8port PCIcontroller is required
Mixed configurations with Eco SATA drives and SAS drives are not allowed
3.5" SAS drives and 3.5" BC SATA drives can be mixed, but not used in one logical RAID volume
Hot replace is only possible running RAID.
S26361-F4005-E530 S26361-F4005-E545
S26361-F4005-E560
HD 300GB 15krpm 3.5" HD 450GB 15krpm 3.5" HD 600GB 15krpm 3.5"
15.000rpm,<4ms, 16MB Cache 15.000rpm,<4ms, 16MB Cache 15.000rpm,<4ms, 16MB Cache
SAS 6Gb/s SAS 6Gb/s SAS 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 8x per system max. 8x per system max. 8x per system
S26361-F5241-E100 S26361-F5241-E200
S26361-F5241-E300
S26361-F5241-E400
HD 1TB 7.2krpm 3.5"
HD 1TB 7.2krpm 3.5" HD 1TB 7.2krpm 3.5" HD 1TB 7.2krpm 3.5"
7200rpm,<9.0 ms, 32MB Cache 7200rpm,<9.0 ms, 32MB Cache 7200rpm,<9.0 ms, 32MB Cache 7200rpm,<9.0 ms, 32MB Cache
BC SAS 6Gb/s BC SAS 6Gb/s BC SAS 6Gb/s BC SAS 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 8x per system max. 8x per system max. 8x per system max. 8x per system
4 / 6 / 8x
S26361-F3670-E500 S26361-F3670-E100
S26361-F3670-E200
S26361-F3670-E300
HD 500GB 7.2krpm 3.5"
HD 1000GB 7.2krpm 3.5"
HD 2000GB 7.2krpm 3.5" HD 3000GB 7.2krpm 3.5"
7200rpm,<9.0 ms, 64MB Cache 7200rpm,<9.0 ms, 64MB Cache 7200rpm,<9.0 ms, 64MB Cache 7200rpm,<9.0 ms, 64MB Cache
BC SATA 6Gb/s
BC SATA 6Gb/s
BC SATA 6Gb/s BC SATA 6Gb/s
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 8x per system max. 8x per system max. 8x per system max. 8x per system
S26361-F3670-E400 3.5" BC SAS - as soon as available
HD 4TB 7.2krpm 3.5"
3.5" BC-SATA 4TB - as soon as available
7200rpm,<9.0 ms, 64MB Cache
BC SATA 6Gb/s
hot plug/hot replace tray
max. 8x per system
K
Fujitsu PRIMERGY Server 19 of 28

System configurator and order-information guide
PRIMERGY TX200 S7 Status 2014-01-30
K
2.5" HDDs for SFF base units; SAS or more than 4 SATA HDDs require a RAID Controller! See section VIII internal Disk Array
Up to 8 SFF (2.5") hard disks can be configured.
With the HDD Extension Box Option D up to 16 SFF (2.5") hard disks can be configured.
With the HDD Extension Box Option D 2 hardware based RAID controllers have to be configured.
The On board SATA Controller can be used with up to 4x 2.5" SATA HDDs (no additional controller required)
If a SAS based backup is configured, then the 4 onboard SATA ports for HDDs are not available any more!
In this case for any HDD solution a PCI based 8port RAID controller is necessary!
For up to 4x 2.5" SAS HDDs with RAID 0/1 functionality a Patsburg Upgrade Kit is required (no SAS tape option)
For up to 4x 2,5" HDDs in combination with a SAS tape or for all other HDD configurations a PCI based
RAID-controllers is required;
Mixed configurations with Eco SATA drives and SAS drives are not allowed
2.5" SAS drives and 2.5" BC SATA drives can be mixed, but not used in one logical RAID volume
Hot replace is only possible running RAID.
Mixed configuration 2.5" BC-SATA/BC-SAS with SAS 10K (S26361-F4483-E130/E145/E160) drives not allowed.
2.5" SAS drives and 2.5" BC SATA drives can be mixed, but not used in one logical RAID volume
S26361-F2826-E426
To be used in
SFF (2.5") HDD-Box for additional
SAS SFF (2.5") Base Unit only
8x SFF (2.5") SAS hard disks
see Conf. diagram Option D
1x Occupies 2x 1.6" bays
in the accessible bay area For the 8x 2.5" HD Extension Box
3.2 * 5.25", satin black bezel 2 PCI based modular RAID controller is necessary
max. 1x per system
see Section VIII
S26361-F2826-E140 For a later configuration of more than 4 SATA HDDs, the trigger is not necessary
Trigger to request a PCI SAS Controller
In this case it is sufficient to implement a SAS controller!
for configuring more than 4 SATA HDDs
It is not allowed to connect the SATA HDDs to different controllers
max. 1x per system In case of running more than 4 HDDs, all of them have
to be connected to the PCI based Controller
as long as stock
S26361-F4541-E100 S26361-F4541-E400 **) High Endurance
SSD SAS 100GB, SLC SSD SAS 400GB, SLC 100GB: max 9PB***,
Solid State Disk, SAS 6Gb/s Solid State Disk, SAS 6Gb/s random write
Enterprise Perfomance Enterprise Perfomance 400GB: max 35PB***,
High Endurance ** High Endurance ** random write
hot plug/hot replace tray
hot plug/hot replace tray
max. 8/16x per system max. 8/16x per system
as long as stock as long as stock
S26361-F4581-E100 S26361-F4581-E200 S26361-F4581-E400 *) Mainstream
SSD SAS 100GB, MLC SSD SAS 200GB, MLC SSD SAS 400GB, MLC Endurance
Solid State Disk, SAS 6Gb/s Solid State Disk, SAS 6Gb/s Solid State Disk, SAS 6Gb/s 10DWPD over 5y
Enterprise Performance Enterprise Performance Enterprise Performance
Mainstream Endurance * Mainstream Endurance * Mainstream Endurance * Managed Life
hot plug/hot replace tray
hot plug/hot replace tray
hot plug/hot replace tray Model
max. 8/16x per system max. 8/16x per system max. 8/16x per system
Solid State Disk Drive, Mainstream Endurance*
SSD SAS 12Gb/s 2.5" with hot plug/hot replace tray as soon as available
200GB, Enterprise Performance
S26361-F5297-E200
Interface SAS12Gb/s and SAS 6Gb/s.
400GB, Enterprise Performance
S26361-F5297-E400 SAS 12Gb/s support is not released
800GB, Enterprise Performance
S26361-F5297-E800
1.6TB, Enterprise Performance S26361-F5297-E160
max. 8/16x per system *) SSD Mainstream Endurance
10DWPD over 5y
K1
Fujitsu PRIMERGY Server 20 of 28