Fujitsu Eternus DX600 S3 Assembly instructions

FUJITSU Storage
ETERNUS DX500 S3/DX600 S3
Disk storage system
Operation Guide (Basic)
P3AM-7742-04ENZ0

This page is intentionally left blank.

Preface
Fujitsu would like to thank you for purchasing our FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage
system (hereinafter referred to as ETERNUS DX).
The ETERNUS DX is designed to be connected to Fujitsu servers (Fujitsu M10, PRIMEQUEST, or PRIMERGY) or
non-Fujitsu servers.
This manual describes the operation management and maintenance of the ETERNUS DX.
This manual is intended for use of the ETERNUS DX in regions other than Japan.
Please carefully review the information outlined in this manual.
Fourth Edition
June 2014
About This Manual
Organization
This manual is composed of the following six chapters:
•"Chapter 1 Component Name/LED Name" (page 12)
This chapter provides component names of the ETERNUS DX500 S3/DX600 S3 Disk storage system.
•"Chapter 2 Basic Operation" (page 40)
This chapter explains how to open and close rack doors and how to turn the ETERNUS DX500 S3/DX600 S3
Disk storage system on and off.
•"Chapter 3 Storage System Monitoring" (page 50)
This chapter describes status monitoring of the ETERNUS DX500 S3/DX600 S3 Disk storage system.
•"Chapter 4 Process Time (Estimated)" (page 54)
This chapter explains the estimated time that is required for volume formatting and for rebuild/copyback
for each RAID level configuration.
•"Chapter 5 Expansion Functions" (page 57)
This chapter explains the expansion functions of the ETERNUS DX.
•"Chapter 6 Maintenance" (page 58)
This chapter describes maintenance once the ETERNUS DX starts to be operated.
•"Chapter 7 Troubleshooting" (page 60)
This chapter explains troubleshooting when errors occur on the ETERNUS DX500 S3/DX600 S3 Disk storage
system.
3
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

Registered Trademarks and Trademarks
•All SPARC trademarks are used under license from SPARC International, Inc. and are trademarks or regis-
tered trademarks of that company in the United States and other countries.
•UNIX is a registered trademark of The Open Group in the United States and other countries.
•Microsoft, Windows, Windows Server, and Internet Explorer are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
•Oracle and Java are registered trademarks of Oracle and/or its affiliates.
•HP-UX is a trademark of Hewlett-Packard Company in the U.S. and other countries.
•Mozilla, Firefox, and the Mozilla and Firefox logos are trademarks or registered trademarks of the Mozilla
Foundation in the United States and other countries.
•Red Hat is a registered trademark of Red Hat, Inc. in the U.S. and other countries.
•Linux is a registered trademark of Linus Torvalds.
•SUSE is a registered trademark of Novell, Inc. in the United States and other countries.
•IBM, AIX, and Tivoli are trademarks of International Business Machines Corporation, registered in many ju-
risdictions worldwide.
•VMware, VMware logos, Virtual SMP, and vMotion are either registered trademarks or trademarks of
VMware, Inc. in the U.S. and/or other countries.
•The company names, product names and service names mentioned in this document are registered trade-
marks or trademarks of their respective companies.
•Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
Naming Conventions
■Product Names
•The following abbreviations are used for Microsoft® Windows Server®.
Product name Abbreviation
Microsoft® Windows Server® 2003, Datacenter Edition Windows Server 2003
Microsoft® Windows Server® 2003, Enterprise Edition
Microsoft® Windows Server® 2003, Standard Edition
Microsoft® Windows Server® 2008 Datacenter
Microsoft® Windows Server® 2008 R2 Datacenter
Windows Server 2008
Microsoft® Windows Server® 2008 Enterprise
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2008 Standard
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 for Itanium-Based Systems
Microsoft® Windows Server® 2008 R2 for Itanium-Based Systems
Microsoft® Windows Server® 2008 HPC Edition
Microsoft® Windows Server® 2008 R2 HPC Edition
Preface
4
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

Product name Abbreviation
Microsoft® Windows Server® 2012 Datacenter
Microsoft® Windows Server® 2012 R2 Datacenter
Windows Server 2012
Microsoft® Windows Server® 2012 Standard
Microsoft® Windows Server® 2012 R2 Standard
Microsoft® Windows Server® 2012 Essentials
Microsoft® Windows Server® 2012 R2 Essentials
•The following abbreviations are used for Red Hat Linux.
Product name Abbreviation
Red Hat Enterprise Linux 5 (for x86)
Red Hat Enterprise Linux 5 (for Intel64)
Red Hat Enterprise Linux 5 (for Intel Itanium)
Red Hat Enterprise Linux 5
Red Hat Enterprise Linux 6 (for x86)
Red Hat Enterprise Linux 6 (for Intel64)
Red Hat Enterprise Linux 6
■Symbols Used in This Manual
The following symbol is used throughout this manual:
This indicates information for the user to note when using the ETERNUS DX. Please be
sure to read this information.
This indicates supplementary and reference information.
■Abbreviations Used in This Manual
•"ETERNUS DX500 S3" refers to the FUJITSU Storage ETERNUS DX500 S3 Disk storage system and "ETERNUS
DX600 S3" refers to the FUJITSU Storage ETERNUS DX600 S3 Disk storage system.
•"ETERNUS DX" refers to the ETERNUS DX500 S3 and ETERNUS DX600 S3 Disk storage systems.
•"CA" refers to a host interface module that is used in an ETERNUS DX to connect to a server.
•"Host Bus Adapter (HBA)" refers to the interface module that is normally used by the server to connect to
ETERNUS DX storage systems.
•Trademark symbols such as ™ and ® are omitted in this document.
Preface
5
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

Warning Signs
Warning signs are shown throughout this manual in order to prevent injury to the user and/or material dam-
age. These signs are composed of a symbol and a message describing the recommended level of caution.
The following explains the symbol, its level of caution, and its meaning as used in this manual.
This symbol indicates the possibility of serious or fatal injury if the ETERNUS DX is not
used properly.
This symbol indicates the possibility of minor or moderate personal injury, as well as
damage to the ETERNUS DX and/or to other users and their property, if the ETERNUS DX
is not used properly.
This symbol indicates IMPORTANT information for the user to note when using the ETER-
NUS DX.
The following symbols are used to indicate the type of warnings or cautions being described.
Electric Shock
The triangle emphasizes the urgency of the WARNING and CAUTION contents. Inside
the triangle and above it are details concerning the symbol (e.g. Electrical Shock).
No Disassembly
The barred "Do Not..." circle warns against certain actions. The action which must be
avoided is both illustrated inside the barred circle and written above it (e.g. No Disas-
sembly).
Unplug
The black "Must Do..." circle indicates actions that must be taken. The required ac-
tion is both illustrated inside the black disk and written above it (e.g. Unplug).
Preface
6
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

How Warnings are Presented in This Manual
A message is written beside the symbol indicating the caution level. This message is marked with a vertical
ribbon in the left margin, to distinguish this warning from ordinary descriptions.
A display example is shown here.
Warning level indicator
Warning type indicator
Warning details
•To avoid damaging the ETERNUS DX, pay attention to the following points
when cleaning the ETERNUS DX:
- Make sure to disconnect the power when cleaning.
- Be careful that no liquid seeps into the ETERNUS DX when using
cleaners, etc.
- Do not use alcohol or other solvents to clean the ETERNUS DX.
Warning layout ribbon
Example warning
CAUTION Do
Preface
7
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

Table of Contents
Chapter 1 Component Name/LED Name 12
1.1 Controller Enclosures.................................................................................................................... 12
1.1.1 Front...................................................................................................................................................................12
1.1.2 Rear ....................................................................................................................................................................14
1.1.3 Components (Front) ...........................................................................................................................................15
1.1.4 Components (Rear) ............................................................................................................................................18
1.2 2.5"/3.5" Type Drive Enclosure ...................................................................................................... 23
1.2.1 Front...................................................................................................................................................................23
1.2.2 Rear ....................................................................................................................................................................24
1.2.3 Components (Front) ...........................................................................................................................................24
1.2.4 Components (Rear) ............................................................................................................................................27
1.3 High-density Drive Enclosure ....................................................................................................... 29
1.3.1 Front...................................................................................................................................................................29
1.3.2 Rear ....................................................................................................................................................................29
1.3.3 Components (Front) ...........................................................................................................................................30
1.3.4 Components (Internal) .......................................................................................................................................32
1.3.5 Components (Rear).............................................................................................................................................33
1.4 19-inch Racks ............................................................................................................................... 36
1.4.1 Front...................................................................................................................................................................36
1.4.2 Rear ....................................................................................................................................................................37
1.5 Power Distribution Units (for Regions Other than EMEA&I).......................................................... 38
1.5.1 Power Distribution Units (1U).............................................................................................................................38
1.5.2 Power Distribution Units (2U).............................................................................................................................39
Chapter 2 Basic Operation 40
2.1 How to Open/Close the Rack Doors............................................................................................... 40
2.1.1 How to Open/Close the Front Door......................................................................................................................40
2.1.2 How to Open/Close the Rear Door .......................................................................................................................41
2.2 Powering On and Off .................................................................................................................... 43
2.2.1 Switching On and Off the Main Line Switch on the Power Distribution Unit (for Regions Other than EMEA&I) .......
.............................................................................................................................................................................43
2.2.2 Switching On and Off the PSU Switch on the Power Supply Unit .........................................................................45
2.2.3 Powering On .......................................................................................................................................................46
8
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

2.2.4 Powering Off.......................................................................................................................................................48
Chapter 3 Storage System Monitoring 50
3.1 Checking LED Status..................................................................................................................... 50
3.2 Displaying Status via ETERNUS Web GUI....................................................................................... 50
3.3 Displaying Status via ETERNUS CLI................................................................................................ 51
3.4 Event Notification......................................................................................................................... 52
3.5 Audit Log...................................................................................................................................... 53
Chapter 4 Process Time (Estimated) 54
4.1 Volume Formatting Time.............................................................................................................. 54
4.2 Rebuild/Copyback Process Time.................................................................................................... 55
Chapter 5 Expansion Functions 57
Chapter 6 Maintenance 58
6.1 Periodic Backup............................................................................................................................ 58
6.2 Maintenance Service .................................................................................................................... 58
6.2.1 Maintenance Support Period ..............................................................................................................................58
6.2.2 Replacing Batteries.............................................................................................................................................59
6.2.3 Related Service ...................................................................................................................................................59
Chapter 7 Troubleshooting 60
7.1 Check List ..................................................................................................................................... 60
7.2 Required Information for Inquiries ............................................................................................... 65
Table of Contents
9
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

List of Figures
Figure 1.1 Front View of a Controller Enclosure (with a Front Cover).........................................................................12
Figure 1.2 Front View of a Controller Enclosure (without a Front Cover)....................................................................13
Figure 1.3 Rear View of a Controller Enclosure (ETERNUS DX500 S3) ........................................................................14
Figure 1.4 Rear View of a Controller Enclosure (ETERNUS DX600 S3) ........................................................................14
Figure 1.5 Operation Panel (Controller Enclosure) ....................................................................................................15
Figure 1.6 PFM..........................................................................................................................................................16
Figure 1.7 Battery .....................................................................................................................................................17
Figure 1.8 Controller (ETERNUS DX500 S3)................................................................................................................18
Figure 1.9 Controller (ETERNUS DX600 S3)................................................................................................................19
Figure 1.10 Controller LEDs.........................................................................................................................................20
Figure 1.11 Host Interface (4port) ..............................................................................................................................21
Figure 1.12 Host Interface (2port) ..............................................................................................................................21
Figure 1.13 Power Supply Unit (Controller Enclosure).................................................................................................22
Figure 1.14 Front View of a 2.5" Type Drive Enclosure.................................................................................................23
Figure 1.15 Front View of a 3.5" Type Drive Enclosure.................................................................................................23
Figure 1.16 Rear View of a 2.5" Type / 3.5" Type Drive Enclosure.................................................................................24
Figure 1.17 Operation Panel (2.5"/3.5" Type Drive Enclosure).....................................................................................24
Figure 1.18 2.5" Drives................................................................................................................................................25
Figure 1.19 Drive Slot Numbers (2.5" Type Drive Enclosure) .......................................................................................25
Figure 1.20 3.5" Drives................................................................................................................................................26
Figure 1.21 Drive Slot Numbers (3.5" Type Drive Enclosure) .......................................................................................26
Figure 1.22 I/O Module (2.5" / 3.5" Type Drive Enclosure) ...........................................................................................27
Figure 1.23 Power Supply Unit (2.5"/3.5" Type Drive Enclosure)..................................................................................28
Figure 1.24 High-density Drive Enclosure ...................................................................................................................29
Figure 1.25 Rear View of a High-density Drive Enclosure ............................................................................................29
Figure 1.26 Operation Panel (High-density Drive Enclosure) ......................................................................................30
Figure 1.27 Disk Activity Panel (DAP)..........................................................................................................................31
Figure 1.28 Drives for High-density Drive Enclosures ..................................................................................................32
Figure 1.29 Drive Slot Numbers for High-density Drive Enclosures..............................................................................32
Figure 1.30 I/O Module (High-density Drive Enclosure) ..............................................................................................33
Figure 1.31 Fan Expander Module ..............................................................................................................................34
Figure 1.32 Power Supply Unit (High-density Drive Enclosure) ...................................................................................35
Figure 1.33 Front View of a 19-inch Rack ....................................................................................................................36
Figure 1.34 Rear View of a 19-inch Rack .....................................................................................................................37
Figure 1.35 Power distribution unit for DX500 S3/DX600 S3 (AC200-240V, 1U 4Outlets) ............................................38
Figure 1.36 Power distribution unit for DX500 S3/DX600 S3 (AC200-240V, 2U, 12Outlets) .........................................39
Figure 1.37 Power distribution unit for DX500 S3/DX600 S3 (AC200-240V, 2U, 16Outlets) .........................................39
Figure 2.1 ON Position (Marked "|") of the Main Line Switches on a 1U Power Distribution Unit ..............................43
Figure 2.2 ON Position (Marked "|") of the Main Line Switches on a 2U Power Distribution Unit ..............................43
Figure 2.3 OFF Position (Marked "¡") of the Main Line Switches on a 1U Power Distribution Unit ...........................44
Figure 2.4 OFF Position (Marked "¡") of the Main Line Switches on a 2U Power Distribution Unit ...........................44
Figure 2.5 ON Position (Marked "|") of the PSU Switch on a Power Supply Unit ........................................................45
Figure 2.6 OFF Position (Marked "¡") of the PSU Switch of a Power Supply Unit ......................................................46
Figure 3.1 ETERNUS Web GUI Screen.........................................................................................................................50
Figure 3.2 Event Notification ....................................................................................................................................53
Figure 3.3 Audit Log..................................................................................................................................................53
10
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

List of Tables
Table 1.1 Status and Meanings of Each LED (Operation Panel (Controller Enclosure)) ............................................15
Table 1.2 Status and Meanings of Each LED (PFM)..................................................................................................16
Table 1.3 Status and Meanings of Each LED (Battery) .............................................................................................17
Table 1.4 Status and Meanings of Each LED (Controller) .........................................................................................20
Table 1.5 Status and Meanings of Each LED (Host Interface)...................................................................................22
Table 1.6 Status and Meanings of Each LED (Power Supply Unit) ............................................................................22
Table 1.7 Status and Meanings of Each LED (Operation Panel (2.5" / 3.5" Type Drive Enclosure))...........................25
Table 1.8 Status and Meanings of Each LED (Drive (2.5" / 3.5" Type Drive Enclosure)) ............................................26
Table 1.9 Status and Meanings of Each LED (I/O Module (2.5" / 3.5" Type Drive Enclosure)) ...................................27
Table 1.10 Status and Meanings of Each LED (Power Supply Unit (2.5" / 3.5" Type Drive Enclosure))........................28
Table 1.11 Status and Meanings of Each LED (Operation Panel (High-density Drive Enclosure)) ..............................30
Table 1.12 Status and Meanings of Each LED (Disk Activity Panel (DAP))..................................................................31
Table 1.13 Status and Meanings of Each LED (I/O Module (High-density Drive Enclosure)) ......................................33
Table 1.14 Status and Meanings of Each LED (Fan Expander Module) ......................................................................34
Table 1.15 Status and Meanings of Each LED (Power Supply Unit (High-density Drive Enclosure))...........................35
Table 3.1 General Status of ETERNUS Web GUI.........................................................................................................51
Table 3.2 General Status of ETERNUS CLI .................................................................................................................51
Table 4.1 Volume Formatting Time (Disk) ...............................................................................................................54
Table 4.2 Rebuild Process Time (Disk) .....................................................................................................................55
Table 4.3 Copyback Process Time (Disk) ..................................................................................................................55
11
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

Chapter 1
Component Name/LED Name
This chapter provides component names of the ETERNUS DX.
1.1 Controller Enclosures
An operation panel is in the front of the controller enclosure. The controllers and the power supply units are
installed in the rear.
1.1.1 Front
This section provides the names of the components in the front of a controller enclosure.
●With a Front Cover
Figure 1.1 Front View of a Controller Enclosure (with a Front Cover)
12
1. Operation panel
2. Front cover
12
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

●Without a Front Cover
Figure 1.2 Front View of a Controller Enclosure (without a Front Cover)
1
2
3
5
6
7
4
1. Battery (BBU#0)
2. Battery (BBU#1)
3. Battery (BBU#2)
4. PCIe Flash Module (CM#0, PFM#0)
5. PCIe Flash Module (CM#0, PFM#1)
6. PCIe Flash Module (CM#1, PFM#0)
7. PCIe Flash Module (CM#1, PFM#1)
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
13
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

1.1.2 Rear
This section provides the names of the components in the rear of a controller enclosure.
●ETERNUS DX500 S3
Figure 1.3 Rear View of a Controller Enclosure (ETERNUS DX500 S3)
34
1
2
●ETERNUS DX600 S3
Figure 1.4 Rear View of a Controller Enclosure (ETERNUS DX600 S3)
34
1
2
1. Controller 0 (CM#0)
2. Controller 1 (CM#1)
3. Power supply unit (CPSU#0)
4. Power supply unit (CPSU#1)
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
14
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

1.1.3 Components (Front)
This section describes the operation panel, PCIe Flash Module (PFM), and the batteries in the front of the
controller enclosure.
■Operation Panel
An operation panel has LEDs and a Power switch.
Figure 1.5 shows the operation panel. Table 1.1 shows the status and meanings of each LED.
Figure 1.5 Operation Panel (Controller Enclosure)
2
3
1
4
65
8
7
1. Power switch
This switch is used to turn on or off the ETERNUS DX.
2. POWER LED
3. IDENTIFY LED
4. FAULT LED
5. MAINTENANCE LED
6. CACHE LED
7. READY LED
8. REMOTE LED
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 1.1 Status and Meanings of Each LED (Operation Panel (Controller Enclosure))
LED name LED status Meanings
POWER
(green)
Power is supplied to the controller enclosure.
IDENTIFY (blinks blue) The installation location of the controller is identified according
to the instruction that is issued from ETERNUS Web GUI or ETER-
NUS CLI.
FAULT (amber) (*1) The ETERNUS DX is in error status.
(blinks amber)
A part of the ETERNUS DX requires preventive maintenance.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
15
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

LED name LED status Meanings
MAINTENANCE
(green)
Maintenance for the ETERNUS DX is in progress.
(blinks green)
Maintenance or a status check via ETERNUS Web GUI or ETERNUS
CLI is necessary for the ETERNUS DX maintenance.
CACHE (green) There is data in the cache memory of the ETERNUS DX.
READY
(green) (*1)
The ETERNUS DX is available for use.
REMOTE (green) The ETERNUS DX is turned on and off with the server.
*1: When the READY LED and the FAULT LED are both on at the same time, an error has occurred while the
Unified configuration is starting up.
■PCIe Flash Module (PFM)
A PFM is a module that is installed to operate the Extreme Cache function.
A PFM has LEDs.
Figure 1.6 shows the PFM. Table 1.2 shows the status and meanings of each LED.
Figure 1.6 PFM
12
1. READY LED
2. FAULT LED
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 1.2 Status and Meanings of Each LED (PFM)
LED name LED status Meaning
READY (green) The PFM is in normal status.
(blinks green)
The PFM is busy or temporarily unavailable.
FAULT (amber) The PFM is in error status.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
16
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

■Batteries
Batteries are used for backup power source in case of power outage.
Batteries have LEDs.
Figure 1.7 shows the battery. Table 1.3 shows the status and meanings of each LED.
Figure 1.7 Battery
1234
1. BRDY LED
2. CHG LED
3. BCA LED
4. BTA LED
The states of LEDs are listed below.
Table 1.3 Status and Meanings of Each LED (Battery)
LED name LED status Meaning
BRDY
(Battery Ready) (green) The battery charge rate is 90% or more.
CHG
(Charge) (green) The battery is being charged or is ready for discharge.
BCA
(BCU Alarm) (amber) The battery is in error status.
BTA
(BTU Alarm) (amber) The battery is in error status.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
17
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

1.1.4 Components (Rear)
This section describes the controllers and the power supply units in the rear of the controller enclosure.
■Controller
The controller contains a CPU, cache memory, host interfaces, Bootup and Utility Device (BUD), and drive in-
terface (DI) ports. The controller controls all operations in the ETERNUS DX.
●Controller (ETERNUS DX500 S3)
Figure 1.8 shows the controller of the ETERNUS DX500 S3.
Figure 1.8 Controller (ETERNUS DX500 S3)
1 2
5734 6
1. Host interface (CA#0)
Install host interfaces.
2. Host interface (CA#1)
Install host interfaces.
3. LAN (FST) port
A port that is dedicated for maintenance engineers. Customers must not use this port.
4. LAN (RMT) port
These are the RJ-45 connectors to connect LAN cables.
5. LAN (MNT) port
These are the RJ-45 connectors to connect LAN cables.
6. DI (OUT) port
This port is used to connect a controller enclosure to a drive enclosure with a cable between enclosures.
7. PWC port
This port is used to connect a power synchronized unit with an RS232C cable.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
18
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

●Controller (ETERNUS DX600 S3)
Figure 1.9 shows the controller of the ETERNUS DX600 S3.
Figure 1.9 Controller (ETERNUS DX600 S3)
1
3
2
4
7956 8
1. Host interface (CA#0)
Install host interfaces.
2. Host interface (CA#1)
Install host interfaces.
3. Host interface (CA#2)
Install host interfaces.
4. Host interface (CA#3)
Install host interfaces.
5. LAN (FST) port
A port that is dedicated for maintenance engineers. Customers must not use this port.
6. LAN (RMT) port
These are the RJ-45 connectors to connect LAN cables.
7. LAN (MNT) port
These are the RJ-45 connectors to connect LAN cables.
8. DI (OUT) port
This port is used to connect a controller enclosure to a drive enclosure with a cable between enclosures.
9. PWC port
This port is used to connect a power synchronized unit with an RS232C cable.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
19
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0

●Controller LEDs
Figure 1.10 shows the LEDs of the controller. Table 1.4 shows the status and meanings of each LED.
Figure 1.10 Controller LEDs
2134 5
678 78
1. READY LED
2. FAULT LED
3. LAN ACCESS LED
4. LAN LINK LED
5. MASTER LED
6. IDENTIFY LED
7. DI (OUT) FAULT LED
8. DI (OUT) LINK LED
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 1.4 Status and Meanings of Each LED (Controller)
LED name LED status Meanings
READY (green) The controller is in normal status.
(blinks green)
An error has occurred during startup.
FAULT (amber)
(blinks amber)
•The controller is in error status.
•An error has occurred during startup.
LAN ACCESS
(blinks green)
Data is being sent or received via the LAN port (for operation
management).
LAN LINK (green) The link between the LAN port (for operation management) and
the destination has been established.
MASTER (green) The controller is set as a Master CM.
IDENTIFY
(blinks blue)
The installation location of the controller is identified according
to the instruction that is issued from ETERNUS Web GUI or ETER-
NUS CLI.
DI (OUT) FAULT (amber)
•The link between the DI (OUT) port and the destination port is
in error status.
•The ports to remove the mini SAS HD cables between enclo-
sures from are indicated. This occurs while a drive enclosure is
being added.
(blinks amber)
The ports to connect the cables are indicated. This occurs while a
drive enclosure is being added.
DI (OUT) LINK (green) The link between the DI (OUT) port and the destination port has
been established.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
20
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-7742-04ENZ0