Fujitsu Streamer DAT 160 User manual

User Guide
Streamer DAT 160 Half-Height
80GB/160GB, USB 2.0 (3.5-inch)
English

User Guide - English
Streamer DAT 160 Half-Height
80GB/160GB, USB 2.0 (3.5-inch)
Edition May 2011

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected]ujitsu.com.
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2011 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

DAT 160 USB
Contents
1 About this guide . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Document conventions and symbols . . . . . . . . . . . . . . 5
1.3 Technical support . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Product warranties . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Before you start . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 DAT 160 tape drive front panel . . . . . . . . . . . . . . . . . 7
2.2 Which operating systems are supported? . . . . . . . . . . 10
2.3 How do I connect the drive to my server? . . . . . . . . . . 10
2.4 What are the mounting requirements for an internal tape drive?
10
2.4.1 Mounting bay . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4.2 Mounting hardware . . . . . . . . . . . . . . . . . . . . . . . 11
2.5 Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6 Backup software . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Installing an internal DAT tape drive . . . . . . . . . . . . . 13
3.1 Prepare mounting bay . . . . . . . . . . . . . . . . . . . . . 13
3.2 Install drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3 Attach cables . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 Secure the drive . . . . . . . . . . . . . . . . . . . . . . . . 18
4 Verify installation . . . . . . . . . . . . . . . . . . . . . . . . 21
5 Use the correct media . . . . . . . . . . . . . . . . . . . . . 23

DAT 160 USB
Contents
5.1 Data cartridges . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1.1 DAT 160 tape drives and DAT 160 cartridges . . . . . . . . . . . 23
5.2 Write-protecting cartridges . . . . . . . . . . . . . . . . . . . 24
5.3 Cleaning cartridges . . . . . . . . . . . . . . . . . . . . . . . 25
5.4 Handling cartridges . . . . . . . . . . . . . . . . . . . . . . . 26
5.5 Getting the most out of cartridges and drives . . . . . . . . . 27
6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.1 General procedure . . . . . . . . . . . . . . . . . . . . . . . . 29
6.2 Verifying USB installation for optimum performance . . . . . 31
6.2.1 Check for USB 2.0 port (Windows) . . . . . . . . . . . . . . . . 31
6.2.2 Ensure that the tape drive is the only device on a USB hub
(Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.2.3 Ensure that the hp_usbstor driver is being used (Windows) . . . 32
6.2.4 Check drivers (Linux) . . . . . . . . . . . . . . . . . . . . . . . 33
6.3 Frequently asked questions about USB drivers . . . . . . . . 34
6.4 Problems with cartridges . . . . . . . . . . . . . . . . . . . . 34
6.4.1 The cartridge is jammed . . . . . . . . . . . . . . . . . . . . . 35
6.4.2 The drive will not accept the cartridge (or ejects it immediately) . 36
7 USB configuration Guide . . . . . . . . . . . . . . . . . . . . 37
7.1 USB in DAT devices . . . . . . . . . . . . . . . . . . . . . . . 37
7.2 USB terminology . . . . . . . . . . . . . . . . . . . . . . . . 37
7.3 Setting up a USB network . . . . . . . . . . . . . . . . . . . . 39
7.4 USB cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

DAT 160 USB 5
1 About this guide
This guide provides information about:
– Installing the DAT USB tape drive
– Using the DAT USB tape drive
– Troubleshooting the DAT USB
1.1 Intended audience
This guide is intended for users who install, operate and maintain the DAT tape
drive.
1.2 Document conventions and symbols
Convention Element
Blue text Cross-reference links and e-mail addresses
Blue, underlined text website addresses
Bold text – Keys that are pressed
– Text typed into a GUI element, such as a box
– GUI elements that are clicked or selected,
such as menu and list items, buttons, tabs,
and check boxes
Italic text Text emphasis
Monospace text – File and directory names
– System output
– Code
– Commands, their arguments, and argument
values
Monospace, italic text – Code variables
– Command variables
Monospace, bold text Emphasized monospace text
Table 1: Document Conventions

6 DAT 160 USB
Technical support About this guide
WWARNING!
Indicates that failure to follow directions could result in bodily harm or
death.
VCAUTION!
Indicates that failure to follow directions could result in damage to
equipment or data.
IProvides additional information.
1.3 Technical support
For worldwide technical support information, see
http://ts.fujitsu.com/support.
Before contacting support, collect the following information:
●Product model names and numbers
●Technical support registration number (if applicable)
●Product serial numbers
●Error messages
●Operating system type and revision level
●Detailed questions
1.4 Product warranties
For information about product warranties, see
http://ts.fujitsu.com/support.

DAT 160 USB 7
2 Before you start
In this chapter:
–“DAT 160 tape drive front panel” on page 7.
–“Which operating systems are supported?” on page 10.
–“How do I connect the drive to my server?” on page 10.
–“What are the mounting requirements for an internal tape drive?” on
page 10.
–“Drivers” on page 11.
–“Backup software” on page 11.
2.1 DAT 160 tape drive front panel
This guide describes how to install and operate the DAT 160 USB tape drive
model.
For a detailed product specification, please refer to your supplier.

8 DAT 160 USB
DAT 160 tape drive front panel Before you start
Figure 1: Front view of DAT 160 tape drive
/
1
0
2
3
1 Clean LED
2 Tape LED
3 Drvie LED
4 Ready LED
5 Eject Button

DAT 160 USB 9
Before you start DAT 160 tape drive front panel
Figure 2: LED sequences

10 DAT 160 USB
Which operating systems are supported? Before you start
2.2 Which operating systems are supported?
DAT USB drives can be connected to servers running under Microsoft Windows
Server 2008, Server 2003, and LinuxKernels 2.6.x. Refer to your supplier for the
most recent information about the operating system versions that are
supported.
2.3 How do I connect the drive to my server?
For optimum performance the drive should be connected to a USB 2.0 port and
it should be the only device on the USB bus. Although the tape drive will function
on USB 1.1, performance will be severely degraded. See also section “Verifying
USB installation for optimum performance” on page 31“
For internal drives, the USB 2.0 connection may be via an internal port on the
server’s system board or an external port on the server’s rear panel.
2.4 What are the mounting requirements for an
internal tape drive?
2.4.1 Mounting bay
You need one industry-standard, 3.5-inch, half-height bay in which to install the
DAT tape drive. Power requirements are:
Voltage Typical Current Maximum Current
DAT 160 DAT 72/DDS-
4/DDS-3
DAT 160 DAT 72/DDS-
4/DDS-3
5 V 1.54 A 0.7 A 1.61 A 0.8 A
12 V 0.26 A 0.3 A 1.3 A 1.0 A
Table 2: Power requirements

DAT 160 USB 11
Before you start Drivers
2.4.2 Mounting hardware
For many servers, no mounting tray or rails are required. Devices simply slide
into the server’s chassis and are fixed with screws. Other servers have built-in
trays or rails.
Some servers use non-standard mounting rails and do not include spares. If this
is the case with your system, you will have to order these accessories from the
server manufacturer before you can install the tape drive.
2.5 Drivers
Two drivers are required in order to use DAT USB tape drives.
–hpdat: This is the tape driver that works with all DAT/DDS tape drive
products. It is regularly updated and is available from
http://ts.fujitsu.com/support.
–hp_usbstor: This is a USB Storage device used by hpdat and it replaces
the Microsoft usbstor driver for USB tape drives. USB DAT drives will work
with the Microsoft usbstor driver, however, we strongly recommend the use
of the hp_usbstor driver as it offers improved functionality.
On Windows systems, we strongly recommend that you use the installer
package supplied to install the drivers BEFORE you connect the tape drive.
Updates to the drivers may be provided from time to time on
http://ts.fujitsu.com/support.We recommend that these are installed after using
the installer package.
On Linux and other operating systems, drivers are included with the operating
system and should be loaded automatically. To upgrade drivers we recommend
that you patch to the latest version of the operating system.
2.6 Backup software
For optimum performance it is important to use a backup application that is
appropriate for your system’s configuration. In a direct attach configuration,
where the tape drive is attached to a standalone server, you can use backup
software that is designed for a single server environment. In network configura-
tions you will need backup software that supports enterprise environments.

12 DAT 160 USB
Backup software Before you start
Further details about suitable products can be found on your supplier’s web site.
It is important to check for software compatibility and install any recommended
upgrades.
ICertain backup applications require you to use their own Tape driver
instead of the HP Tape driver.

DAT 160 USB 13
3 Installing an internal DAT tape
drive
In this chapter:
–“Prepare mounting bay” on page 13.
–“Install drive” on page 14
–“Attach cables” on page 16
–“Secure the drive” on page 18
IIt is important to ensure that you connect your drive to a USB 2.0 port.
The drive will work on a USB 1.1 port but performance will be severely
degraded. See also“Verifying USB installation for optimum performance”
on page 31.
3.1 Prepare mounting bay
You need one industry-standard, 3.5-inch bay in which to install the DAT tape
drive.
WWARNING
To avoid personal injury or damage to the server or tape drive, ensure
that the server is disconnected from the mains power supply while you
install the drive.
VCAUTION
Static electricity can damage electronic components. Always wear an
antistatic wriststrap if one is available. If not, after you have disconnected
power from the server and removed the cover, touch a bare metal part of
the chassis. Similarly, touch a bare metal part of the drive before
installing it.
ÊRefer to your server documentation for detailed instructions and assemble
the necessary tools and materials.
ÊPerform a normal system shutdown and turn off the server and any
connected peripherals.
ÊRemove the cover and access panel from the server, as detailed in your
server’s documentation.

14 DAT 160 USB
Install drive Installing an internal DAT tape drive
As you work inside the server, you may have to disconnect other signal
cables or power cables from other devices to maneuver the new drive into
place. If you have to do this, make a note of their position and connections
so you can put them back correctly later.
ÊRemove the filler panel from a spare 3.5-inch bay of your server, as
described in your server’s documentation. With some servers you may also
need to remove the half-height device divider. Keep any screws for use in
“Secure the drive” on page 18.
ÊYou are now ready to install your tape drive.
3.2 Install drive
VCaution
Static electricity can damage electronic components. Always wear an
antistatic wriststrap if one is available. If not, after you have disconnected
power from the server and removed the cover, touch a bare metal part of
the chassis. Similarly, touch a bare metal part of the drive before
installing it.
Slide the tape drive into the open bay, aligning the tray or rails with the slots in
the bay, as shown in the figure “Installing tape drive” below.

DAT 160 USB 15
Installing an internal DAT tape drive Install drive
Figure 3: Installing tape drive
The illustration shows a tape drive that has mounting rails fitted. If your server
does not use mounting hardware, check that the holes in the chassis are aligned
with the holes in the side of the tape drive.
Do not secure the drive at this point because you may have to move the drive to
get the cables into place.

16 DAT 160 USB
Attach cables Installing an internal DAT tape drive
3.3 Attach cables
The drive is not powered from the USB bus. It must be connected to the server’s
power supply.
The tape drive is connected to a standard, internal USB port on your server. Use
the schematic on the inside of the server panel to check whether the server has
an internal USB port and locate its position. If your server does not have an
internal USB 2.0 port, you will need to purchase and install a suitable USB host
adapter before connecting the USB tape drive.
ÊUse a standard USB cable to connect to the server. Use cable ties, as
required, to tidy excess cable length.
ÊAttach a spare power cable from the server’s internal power supply to the
power connector.

DAT 160 USB 17
Installing an internal DAT tape drive Attach cables
Figure 4: Attaching drive
1 and 5 USB cable, to server’s external USB port
2 and 4 power cable
3 tape drive
6 server’s power supply

18 DAT 160 USB
Secure the drive Installing an internal DAT tape drive
3.4 Secure the drive
ÊSecure the drive, as described in your server documentation. The following
diagrams are examples only.
Figure 5: Securing drive example 1, mounting hardware used
1 plastic rail
2 server latch, push down to lock the tape drive into position

DAT 160 USB 19
Installing an internal DAT tape drive Secure the drive
Figure 6: Securing drive example 2, no mounting hardware used
ÊEnsure blanking plates are in place over empty bays and replace the cover
on the server.
1 M3 screws, supplied with tape drive