Furniture of America California CM-BK589 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 11
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-BK589
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]
Rev: 18-07-25

Page 2 of 11
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 11
#1 x 1pc
Lower End Guardail(L)
#2 x 1pc
Lower End Guardail(R)
#3 x 1pc
Center End Guardail(L)
#4 x 1pc
Center End Guardail(R)
#5 x 1pc
Upper End Guardail(L)
#6 x 1pc
Upper End Guardail(R)
#7 x 1pc
Lower Front Side Rail
#8 x 1pc
Lower Back Side Rail
#9 x 1pc
Center Front Side Rail
#10 x 2pcs
Upper/Center Back Side Rail
#11 x 1pc
Upper Front Side Rail
#12 x 4pcs
Back Guardrail
#13 x 4pcs
Front Guardrail
#14 x 6pcs
#15 x 1pc
Long Ladder Rail (R)
#16 x 1pc
Long Ladder Rail (L)
Guardrail Support

Parts List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 11
#17 x 1pc
Short Ladder Rail (R)
#18 x 1pc
Short Ladder Rail (L)
#19 x 7pcs
Ladder Rung
#20 x 3set
Twin Slat Kit
Hardware List
#A x 36pcs
#B x 36pcs
#D x 18pcs
#F x 32pcs
Bolt Ø1/4"x3-1/2"
#G x 8pcs
#H x 24pcs#C x 14pcs
Barrel Nut Ø1/4"x1/2"
Wood Dowel Ø7/16"x40mm
Screw 3/16"x30mm
#I x 1pc
Allen Wrench 4mm
#E x 14pcs
Screw Ø1/4"x2"
Bolt Ø1/4"x1-9/16"
Bolt Ø1/4"x1-3/16"
Metal Dowel Ø3/8"x90mm
#J x 18pcs
Hex Cap Ø1/4"x5/8"

Page 5 of 11
#1
#2
#3
#4
#6
#5
#7
#8
#9
#10
#10
#11
#13
#12
#12
#13
#14
#14
#14
#14
#15
#16
#19
#17
#18
#19
#20
#20
#20
Exploded View

Page 6 of 11
#A x 8pcs
#B x 8pcs
#A x 14pcs
#B x 14pcs
#F x 12pcs
#7
#2
#1
#8
#A
#I
#B
#A
#F
#B
#I
#9
#4
#3
#10
#12
#A
#I
#B
#13
Align side rails (#7,8) to the guardrails (#1,2), then secure by
tightening bolts (#A) to barrel nuts (#B).
Insert dowels (#F) to guardrails (#12,13), then align guardrails
(#12,13) and side rails (#9,10) to end guardrails (#3,4). Secure
by tightening bolts (#A) with barrel nuts (#B).

Page 7 of 11
#D x 9pcs
#A x 14pcs
#B x 14pcs
#F x 12pcs
#J x 9pcs
#13
#14
#14
#D
#I
#J
#11
#6
#5
#10
#A
#I
#B
#A
#F
#B
#I
#13
#12
#12
Align guardrail supports (#14) to the holes of the guardrails
(#12,13), then secure by tightening bolts (#D) to hex cap (#J).
Insert dowels (#F) to guardrails (#12,13), then align guardrails
(#12,13) and side rails (#10,11) to end guardrails (#5,6). Secure
by tightening bolts (#A) with barrel nuts (#B).

Page 8 of 11
#G x 8pcs
#D x 9pcs
#J x 9pcs
#13
#14
#14
#G
#G
#G
#G
#G
#G
#G
#G
#I
#D
#J
#12
#1
#2
#4
#6
#3
#5
Align guardrail supports (#14) to the holes of the
guardrails (#12,13), then secure by tightening bolts
(#D) to hex cap (#J).
Insert metal dowels (#G) before
stacking each layer of bunk
beds.

Page 9 of 11
#19
#16
#15
#E
#E x 10pcs
#19
#18
#17
#E x 4pcs
#I
#E
#I
#E
#I
#E
#I
Align ladder rungs (#19) to the ladder rails (#15,16), then
secure by using screws (#E).
Align ladder rungs (#19) to the ladder rails (#17,18),
then secure by using screws (#E).

#C x 14pcs
#F x 8pcs
#H x 24pcs
#C
#F
#I #C
#H
#H
#20
#20
#20
#I
#7
#9
#11
#13
#7
#8
#9
#10
#10
#11
#16
#15
#17
#18
Page 10 of 11
Align longer and shorter ladders to the appropriate spot as
shown in the diagram, then secure by using bolts (#C).
Align slats (#20) to the bunk bed, then secure by
using screws (#H).