Furniture of America Orbe CM4006-3PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-19
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM4006-3PK

Page 2 of 5

Parts List Hardware List
#1 x 1 pc x 3
Table Glass
#2 x 1 pc x 3
Table Top
#3 x 2 pcs x 3
Cross Supports
#A x 11 pcs x 3
Bolt 1/4”x1-1/4”
#B x 11 pcs x 3
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 3 pcs x 3
Flat Washer
MD
#D x 8 pcs x 3
Flat Washer
#4 x 1 pc x 3
Bottom Base
Page 3 of 5
#E x 4 pcs x 3
Wood Dowel
#F x 1 pc
Allen Wrench
#5 x 4 pcs x 3
Foot
Note: The above parts and hardware are shown for a
complete assembly of ONE table. However, the actual parts
and hardware (with an exception of the Allen wrench) in the
box will be thrice the quantities due to the packaging of
THREE tables in a box.

I. Insert 4 wood dowels (#E) onto the
bottom base (#4).
II. Align the foot (#5) with the wood
dowel (#E) and the pre-drilled hole
on the corner of the bottom base
(#4).
III. Prepare a bolt assembly by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the
flat washer (#D) onto the SAME
bolt (#A), in that order.
IV. Insert the bolt assembly through the
hole of the foot (#5) and secure that
bolt using the Allen wrench (#F) to
lock it in with the bottom base (#4).
V. Repeat the process for the
remaining 3 feet (#5).
#2
I. Position the cross supports (#3)
to form an “X”.
II. Align the bottom base (#4) with
the 4 pre-drilled holes of the
cross supports (#3).
III. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then
the flat washer (#D) onto the
SAME bolt (#A), in that order.
IV. Insert the 4 bolt assemblies
through the holes of the bottom
base (#4) and secure those bolts
using the Allen wrench (#F) to
lock them in with the cross
supports.
Turn right (clockwise) to tighten
Page 4 of 5
#4
#A x 4 pcs
#B x 4 pcs
#D x 4 pcs
#A x 4 pcs
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
#1

Page 5 of 5
#4 I. Due to the fragile nature of the glass, take caution when
inserting the table glass (#1) onto the table top (#2).
II. Make sure the table is rested on a flat surface and it does
not feel loose or wobbly. If it does, double check that the
bolts are secured and properly tighten.
#3
Turn right (clockwise) to tighten
#2
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs
I. Carefully place the table top
(#2) facing down on a protected
surface. Align the cross
support assembly with the 3
pre-drilled holes on the bottom
of the table top (#2).
II. Prepare 3 bolt assemblies by
inserting FIRST the lock
washer (#B) onto the bolt (#A)
and then the flat washer (#C)
onto the SAME bolt (#A), in
that order.
III. Insert the 3 bolt assemblies
through the cross supports (#3)
and secure those bolts using
the Allen wrench (#F) to lock
them in with the table top (#2).
Assemble everything exactly the
same for the other two tables.
ASSEMBLY IS COMPLETED
#3