Furniture of America CM7811CK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-20
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
CM7811CK
Phillips Screwdriver (Not Included)
2 PERSONS RECOMMENDED
CM7811EK

Page 2 of 7

Parts List
#1 x 1 pc
Left Headboard Post
#2 x 1 pc
Right Headboard Post
#3 x 1 pc
Headboard
#D x 1 pc
Allen Wrench
Before you begin, please read Page 2 of
“Assembly and Care Advice”.
And remember, do not tighten until each step
is completed or instructed.
MD
#C x 14 pcs
Flat Washer
#4 x 1 pc
Footboard
Page 3 of 7
#E x 8 pcs
Screw 1-1/4”
Hardware List
#6 x 2 pcs
Side Rail
#7 x 4 pcs
Finial
#A x 6 pcs
Bolt 1/4”x1-3/4”
#B x 14 pcs
Lock Washer
#F x 4 pcs
Screw 5/8”
#8 x 4 pcs
Slat
#9 x 8 pcs
Slat Support Leg
#5 x 2 pcs
Footboard Leg
#G x 8 pcs
Bolt 5/16”x1”

Page 4 of 7
Turn right (clockwise) to tighten
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling
of the product and to avoid any potential injury
and/or damage.
Enlarged
Align the threaded end of the footboard leg (#5)
with the pre-drilled hole on the bottom of the
footboard (#4) and tighten by hands until secured.
Repeat for the other footboard leg (#5).

Page 5 of 7
Enlarged
Back Side
#A x 6 pcs
#B x 6 pcs
#C x 6 pcs
#F x 4 pcs
I. Align the left and right headboard posts (#1 & #2) with the
headboard (#3).
II. Prepare 6 bolt assemblies by inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert two bolt assemblies through the top holes of the
headboard (#3) and secure those bolts using the Allen wrench
(#D) to lock them in with the left and right headboard posts
(#1-#2) .
IV. Insert 4 bolt assemblies through the bottom holes of the
headboard (#3) and secure those bolts using the Allen wrench
(#D) to lock them in with the left and right headboard posts
(#1-#2) .
V. Insert 4 screws (#F) through middle area of the headboard
(#3) and secure those screws using a Phillips screwdriver to
lock them in with the left and right headboard posts (#1-#2).
Turn right (clockwise) to tighten
Note: Right and left are determined by
standing in FRONT of the completed bed.
Enlarged

Turn right (clockwise) to tighten
Page 6 of 7
Enlarged
Enlarged
#B x 8 pcs
#C x 8 pcs
#G x 8 pcs
Turn right (clockwise) to tighten
I. Prepare 4 bolt assemblies by inserting
FIRST the lock washer (#B) onto the
bolt (#G) and then the flat washer (#C)
onto the SAME bolt (#G), in that order.
II. Insert the 4 bolt assemblies through the
pre-drilled holes of the left and right
headboard posts (#1-#2) using the Allen
wrench (#D) but expose about ½” of the
bolt’s thread in order to mount the side
rail brackets onto the bolts (#G).
III. Mount the brackets of the side rails (#6)
onto the bolts of the left and right
headboard posts (#1 & #2). Make sure
both the washers are in the front of the
brackets. Use the Allen wrench (#D) to
tighten the bolts with the two parts
together.
IV. Repeat the process I through III above
to assemble the other ends of the side
rails (#6) onto the footboard (#4).
Align the threaded end of the finials (#7) with the pre-drilled holes on
top of the left and right headboard posts (#1 & #2) AND on top of the
footboard (#4) and tighten by hand until secured.

.
Align the ends of the 4 assembled slat (#8) with the pre-drilled
holes on each side of the side rails (#6). Secure two wood
screws (#E) for each slat (#8) by using a Phillips screwdriver to
tighten them down to the side rails (#6).
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 7 of 7
Enlarged
Enlarged
#E x 8 pcs
Each slat (#8) has two slat support legs (#9). Align the
threaded end of the slat support legs (#9) with the pre-drilled
holes of the slat (#8) and tighten by hand until secured. Repeat
the process for attaching the remaining 6 slat support legs (#9)
onto the slats (#8).
ASSEMBLY IS COMPLETED
Adjust the leveler
according to the ground
level. To lower or to
raise the slat support leg,
you need to turn the
leveler clockwise or
counterclockwise,
respectively.