Furniture of America CM-AC6051 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 16
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-09-06
CM-AC6051
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page 2 of 16
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Page 3 of 16
Cam Lock
Cam Lock Fastener Assembly
Cam Pin
Cam Lock are fasteners used to join two boards
together, usually the edge of one board (A) to the flat
side of another board (B).
Flat side
Board A
Board B
edge to
join
To use Cam Lock
Fasteners:
Step 1 - Insert
cam Pin into the
flat side of a
board. Tighten
only until snug. Do
not over-tighten
Step 2 - Fit the
hole in the
edge of the
joining board
over the Cam
Pin. The head
of the Cam Pin
will be visible in
the large hole
in the side of
the joining
board, as in
Step 3.
Step 3 - Notice the Cam Lock has a "C" -Shaped back. An
arrow on the front points the same direction as the open
section. Insert the Cam Lock into the large hole so the
opening of the "C" fits over the head of the Cam Pin.
arrow head of the Cam Pin
Open section of back
fits over the head os
the Cam Pin
Step 4 - Use a flat screwdriver to turn the Cam Lock
clockwise on half a turn so it locks onto the head of the Cam
Pin. Turn only until it is snug - over-tightening could cause the
Cam to bend or break.
If is will not turn the full amount, turn the Cam Pin out
(counter- clockwese ) one full turn, and try the Cam Lock
again.

Parts List
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 16
#1 x 3pcs
Shelf Panel
#2 x 1pc
Top Back Panel
#3 x 2pcs
Middle Back Panel
#4 x 1pc
Upper Panel
#5 x 1pc
Bottom Panel
#6 x 1pc
Left Panel
#7 x 1pc
Right Panel
#8 x 1pc
Back Panel
#A x 22pcs
Wood Dowel Ø8x30mm
#B x 18pcs
Cam Pin
#C x 18pcs
Cam Lock
#D x 36pcs
Bolt Ø1/4" x 1/2"
#E x 8pcs
Bolt Ø5/32" x 1/2"
#F x 4pcs
Shelf Pin
#G x 18pcs
Plastic Cap
#H x 1pc
Allen Wrench M4

Parts List
Page 5 of 16
#9 x 1pc
Door
#10 x 1pc
Drawer Shelf Panel
#11 x 1pc
Left Side Frame
#12 x 1pc
Right Side Frame
#6
#7
#9
#10
#1
#2
#3
#4
#5
#8
#11
#12
Hardware List
#I x 2set
Anti-Tip Kits

Page 6 of 16
#A x 2pcs
#2
#A
#3
#A
x 2
#A x 2pcs

#3
#1
Page 7 of 16

#A x 6pcs
#B x 6pcs
#4
#A
#B
#A x 6pcs
#B x 6pcs
#5
#A
#B
Page 8 of 16

Page 9 of 16
#A
#B
#B
#8
#A x 4pcs
#B x 6pcs
#C x 3pcs
#6
#8
#C

Page 10 of 16
#8
#6
#7
#C
#C x 3pcs
#C x 6pcs
#C
#4
#8
#6
#7
#C

Page 11 of 16
#6
#7
#5
#C
#C x 6pcs
#C
#H
#D
#1
#12
#D x 8pcs
#5

Page 12 of 16
#2
#8
#3
#3
#12
#D
#H
#D x 9pcs
#H
#D
#11
#D x 8pcs
#1
#1
#1
#5
#D
#H

Page 13 of 16
#D x 9pcs #D
#H
#11
#E x 8pcs
#E
#9
#2
#3
#3
#8
#7
#D
#H

Page 14 of 16
#F x 4pcs
#G
#G x 18pcs
#10
#F

Page 15 of 16
#D x 2pcs
#I x 2 set
#H
#D
#I
#3
ASSEMBLY IS COMPLETED

Page 16 of 16
Side to Side Adjustment
loosen screw A, adjust gap
with screw B and re-tighten
Screw A.Depth Adjustment
loosen screw A, push hinge
arm forwards or backwards,
re-tighten screw A and secure
Screw B with a 1/4 turn
clockwise.
Height Adjustment
loosen screw C, adjust door
height and re-tighten screw C.
* The doors can be adjusted in all 3 directions to create an even fit between doors on this cabinet.
Follow the appropriate directions above to adjust door(s) as necessary.
A
B
A
C
B