Furniture of America CM-BK450FF User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 10
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 16-12-09
CM-BK450FF
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page 2 of 10
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

#1 x 1pc
#2 x 1pc
#3 x 1pc
#4 x 1pc
#5 x 1pc
#6 x 1pc
#7 x 1pc
#8 x 1pc
#9 x 1pc
#10 x 1pc
#11 x 4pcs
#12 x 1pc
Center Support
#13 x 2pcs
#14 x 1set
Top Slat Kit (13pcs)
#15 x 1set
Bottom Slat Kit (13pcs)
Headboard (Left)
Headboard (Right)
Back Guardrail
Front Guardrail
Ladder Rail (Left)
Ladder Rail (Right)
Ladder Rung
Lower Front Side Rail
Lower Back Side Rail
Upper Front Side Rail
Upper Back Side Rail
Parts List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 10
Support Leg 320x40x40mm

#A x 16pcs
Bolt Ø1/4" x 4-7/8"
#C x 6pcs
Bolt Ø1/4" x 2-3/4"
#B x 16pcs
Barrel Nut Ø1/4" x 1/2"
#D x 4pcs
Bolt Ø1/4" x 1-9/16"
#E x 8pcs
Bolt Ø1/4" x 1-3/16"
#F x 8pcs
Screw Ø1/4" x 2"
#G x 22pcs
Screw #3/16" x 1-3/16"
#I x 1pc
Allen Wrench 4mm
#H x 2pcs
Screw #3/16" x 1-9/16"
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 10

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 5 of 10
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
#12
#13
#14
#15

Page 6 of 10
#I
#C
#E
#A x 16pcs
#B x 16pcs
#A
#B
#I
#E
#I
#C x 6pcs
#E x 8pcs
#1
#2
#3
#4
#5
#6
#7
#8
#1
#2
#6
#5
Insert barrel nuts (#B)
into the holes of the
side rails (#3,4,5,6).
Align side rails
(#3,4,5,6) to the holes
of the headboard
(#1,2) as shown in the
picture. Secure with
bolts (#H) by attaching
bolts (#H) to the barrel
nuts (#B).
2) Align front guardrail (#8)
to the holes of the headboard
(#1,2) and side rail (#5).
Secure holes aligned to
headboard (#1,2) with bolts
(#C). Secure holes aligned to
side rail (#5) with bolts (#E).
1) Align the back guardrail
(#7) to the holes of the
headboard (#1,2) and side
rail (#6). Secure holes
aligned to headboards (#1,2)
with bolts (#C). Secure holes
aligned to side rail (#6) with
bolts (#E).

Page 7 of 10
#G
#G x 2pcs
#F x 8pcs
#12
#I
#F
#F
#9
#10
#11
#2
#1
Align center support (#12) to the "U" shaped block of
the upper headboards (#1,2). Secure wtih screws (#G).
Align ladder rungs (#11) to the holes of the ladder rails (#9,10). Secure with screws (#F).

Page 8 of 10
#D
#I
#D
#I
#D x 4pcs
#H x 2pcs
#H
#13
#15
#3
#5
Align ladder to the holes of the side rails (#3,5).
Secure the ladder with bolts (#D).
Align support legs (#13) to the holes of the bottom slat kit (#15),
then secure wtih screws (#H).

Page 9 of 10
#G x 20pcs
#14
#15
#G
#G
ASSEMBLY IS COMPLETED
#3
#4
#5
#6
1) Align top slat kit (#14) to the top side rails,
then secure with screws (#G).
2) Align bottom slats (#15) to the bottom side
rails, then secure with screws (#G).

Page 10 of 10