Furniture of America CM-BK606A User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-BK606A/WH/EX/CH
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-07-16
Page 1 of 11
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Phillips Screwdriver (Not Included)

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 11

Page 3 of 11

#4 x 2 pcs
Front Side Rail
Parts List
#1 x 1 pc
Upper Rt. End G/Rail
#3 x 2 pcs
Lower End G/Rail
#7 x 2 pcs
Front Guardrail
Before you begin, please read Page 3
for “Assembly and Care Advice” AND
Page 11 for “Safety Warnings”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 4 of 11
#9 x 2 pcs
Guardrail Support
#6 x 2 pcs
Rear Guardrail
#10 x 1 pc
Left Ladder Rail
#2 x 1 pc
Upper Lt. End G/Rail
#5 x 2 pcs
Rear Side Rail
#8 x 2 pcs
Slat
#11 x 1 pc
Right Ladder Rail #12 x 3 pcs
Ladder Rung
Note: Right and left are determined by
facing the ladder of the fully-assembled
bunk bed.

#D x 6 pcs
Screw 6x45mm
Hardware List
#A x 16 pcs
Bolt 1/4”x105mm
#C x 6 pcs
Screw 6x45mm
#G x 1 pc
Allen Wrench
Page 5 of 11
#F x 4 pcs
Dowel
#B x 6 pcs
Bolt 1/4”x35mm
#E x 30 pcs
Wood Screw
#H x 16 pcs
Rail Bracket
Due to the size and/or weight of this product, it
is highly recommended that the assembly
should be done near the area of its intended
location. Make sure you have enough space to
move around during the assembly. ALWAYS
have at least two people to help with
transporting and assembling the product to
avoid any potential injury and/or damage.

Page 6 of 11
Turn right (clockwise) to tighten
#A x 8 pcs
#H x 8 pcs
#F x 4 pcs

Page 7 of 11
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
#A x 8 pcs
#D x 4 pcs
#H x 8 pcs
#C x 6 pcs

Page 8 of 11
Turn right (clockwise) to tighten
#B x 4 pcs

Page 9 of 11
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
#B x 2 pcs
#D x 2 pcs
#E x 24 pcs

Page 10 of 11
Turn right (clockwise) to tighten
ASSEMBLY IS COMPLETED
Safety is ALWAYS the main priority.
For extra safety measure and before
using the bed, please take the time to
inspect the assembly again and make
sure that ALL bolts and screws are
FULLY tightened.
Read and follow the information on
the WARNINGS shown on the end
structure of the upper bunk and on
the carton. Do not remove warning
label from the bed. Keep these
instructions for future reference.
#E x 6 pcs

Page 11 of 11
Safety Warnings for Bunk Beds
1. Read and follow the information on the WARNINGS shown on the end
structure of the upper bunk and on the carton. Do not remove warning label
from the bed. Keep these instructions for future reference.
2. Always use the recommended size mattress or mattress support, or both, to
help prevent the likelihood of entrapment or falls. The proper mattress sizes
for the UPPER TWIN-SIZE bunk should be 74” to 75” long x 37½” to 38½”
wide x 6” high (no higher than 6”) and for the LOWER TWIN-SIZE bunk
should be 74” to 75” long x 37½” to 38½” wide x 6” to 8” high.
3. Surface of mattress must be at least 5 inches (127 mm) BELOW the upper
edge of guardrails.
4. Do not allow persons under 6 years of age to use the upper bunk.
5. Periodically check and ensure that the guardrails, ladder, handle and other
components are in their proper position, free from damage, and that all
connectors are tighten and secured.
6. For safety reasons, especially on the upper bunk bed, DO NOT allow rough
playing or jumping on the bed and do not allow playing or hiding under the
bed.
7. Always use the ladder for entering and leaving the upper bunk.
8. Do not use substitute parts. Contact the manufacturer or dealer for
replacement parts.
9. Use of a nightlight may provide added safety precaution for a person using
the upper bunk.
10. Always use the guardrails on both long sides of the upper bunk. If the bunk
bed will be placed next to the wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
11. The use of water or sleep flotation mattresses is prohibited.
12. No more than one person is allowed on the upper bunk at all times.
13. The MAXIMUM weight capacity for the upper bunk is not to exceed 150 lbs.
WARNING:
STRANGULATION HAZARD
Never attach or hang objects to any part of the bunk bed
that are not designed for use with the bed. Objects such as
hanger, hook, belt, bag, rope, string, etc. should not be used
on or around the bunk bed.