Furniture of America CM-DK6431 User manual

Assembly
Instructions
EASY DIFFICULT
Page 1 of 6
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-DK6431
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Rev:16-09-01
Phillips Screwdriver
(Not Included)

Page
2 of 6
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches
Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 4pcs
#F x 4pcs
#A x 10pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Cabinet body
#3 x 1pc
#B x 8pcs
Page 3 of 6
Leg
Mirror Base
Bolt M4 x 1"
Bolt Ø1/4" x 2"
Lock Washer Ø1/4"
#4 x 2pcs
#5 x 1pc
Mirror Support
Mirror
#E x 2pcs
#D x 1pc
Barrel Nuts Ø1/4"
#C x 8pcs
Flat Washer Ø1/4"
#H x 4pcs
Flat Washer M4
#G x 2pcs
Mirror Bolt Ø5/16"x8x1-7/9"
Allen Key 4mm

#A
#B
#D
#D
#A
#E
#C
#1
#2
Page
4 of 6
#A x 8pcs
#B x 8pcs
#C x 8pcs
#A x 2pcs
#E x 2pcs
#3
#1
1. Prepare 8 bolt assemblies by first inserting a
lock washer (#B) onto the bolt (#A) then a
flat washer (#C) onto that same bolt (#A).
Pull out drawer for
access to rear holes.
2. Align the legs (#2) to the
holes along the corners of
the cabinet body (#1), then
insert the bolt assemblies
from within and secure
using the Allen wrench (#F).
1. Insert the barrel nut (#E)
into the large holes along
the mirror base (#3), make
sure to align the hole.
2. Align the mirror base (#3) to
the holes along the top of the
body (#1), then insert the bolt
(#A) from below. Secure
using the Allen wrench (#D).

#F
#G
#H
Page 5 of 6
#F x 4pcs
#H x 4pcs
#G x 2pcs
#3
#4
#4
#4
#5
#4
Align the mirror supports
(#4) to the base (#3), then
insert a bolt (#F) with flat
washer (#H) into each hole.
Secure using a screwdriver.
Align the mirror (#5) to the holes along the
mirror supports (#4) then insert the mirror
bolts (#G) and turn right to tighten.

#A
#B
#D
#C
#2
#1
Parts List
Hardware List
#1 x 1pc
#2 x 4pcs
#A x 8pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Seat
#B x 8pcs
Page 6 of 6
Leg
Bolt Ø1/4" x 2"
Lock Washer Ø1/4"
#D x 1pc
Allen Key 4mm
#A x 8pcs
#B x 8pcs
#C x 8pcs
#C x 8pcs
Flat Washer Ø1/4"
2. Align the legs (#2) to the holes along the corners of the seat
(#1), then insert the bolt assemblies from within and secure.
1. Prepare 8 bolt assemblies by first inserting a lock washer (#B)
onto the bolt (#A) then a flat washer (#C) onto that same bolt (#A).