Furniture of America CM3710PC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM3710PC-2PK
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-18
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
Phillips Screwdriver
(Not Included)

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 6

Page 3 of 6

Parts List Hardware List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 1 pc x 2
Right Front Leg
#A x 10 pcs x 2
Flat Washer
#B x 10 pcs x 2
Lock Washer
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 4 pcs x 2
Bolt 5/16”x3-1/2”
MD
#D x 2 pcs x 2
Bolt 5/16”x1-3/4”
Page 4 of 6
#E x 4 pcs x 2
Bolt 5/16”x2-1/4”
#F x 1 pc
Allen Wrench
Note: The above parts and hardware are shown for a complete
assembly of ONE chair. However, the actual parts and hardware
(with an exception of the Allen wrench) in the box will be twice
the quantities listed to include the assembly of the second chair.
#4 x 1 pc x 2
Left Front Leg
#5 x 1 pc x 2
Right Leg Support
#6 x 1 pc x 2
Left Leg Support
#7 x 1 pc x 2
Front Leg Support #G x 6 pcs x 2
Wood Screw

I. Place the backrest with legs
(#1) on a protected surface.
Align the seat (#2) with the
pre-drilled holes of the
backrest with legs (#1).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock
washer (#B) onto the bolt (#D)
and then the flat washer (#A)
onto the SAME bolt (#D), in
that order.
III. Insert the bolt assembly near
the center holes of the seat
(#2) and secure those bolts
using the Allen wrench (#F) to
lock them with the backrest
with legs (#1).
Turn right (clockwise) to tighten
Page 5 of 6
#A x 2 pcs
#B x 2 pcs
#D x 2 pcs
I. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#B) onto the bolt
(#C) and then the flat washer
(#A) onto the SAME bolt
(#C), in that order.
II. Insert the bolt assemblies
through the pre-drilled holes
in the corners of the seat (#2)
and secure those bolts using
the Allen wrench (#F) to lock
them with the backrest with
legs (#1).
Turn right (clockwise) to tighten
#A x 4 pcs
#B x 4 pcs
#C x 4 pcs

Page 6 of 6
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR
Turn right (clockwise) to tighten
I. Secure all the leg supports with
6 wood screws (#G) using a
Phillips screwdriver to lock them
with the backrest with legs (#1),
the right front leg (#3) and the
left front leg (#4).
II. Carefully place the completed
chair upright. Make sure the
chair is rested on a flat surface
and does not feel loose or
wobbly. If it does, double check
that the bolts are secured and
properly tightened.
#G x 6 pcs
#A x 4 pcs
#B x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten
I. Insert the front leg support (#7)
between the right front leg (#3)
and the left front leg (#4).
II. Insert the right leg support (#5)
and the left leg support (#6) into
the backrest with legs (#1) and
the other ends of the leg
supports into the assembled
right front leg (#3) and the left
front leg (#4).
III. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#E) and then
the flat washer (#A) onto the
SAME bolt (#E), in that order.
IV. Insert the bolt assemblies
through the corners of the seat
(#2) and secure those bolts
using the Allen wrench (#F) to
lock them with the right front leg
(#3) and the left front leg (#4).
Note: Right and left are
determined by facing the front of
the chair in the upright position.