Furniture of America CM7008F User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7008F/Q
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-04
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 7

Page 3 of 7

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 2 pcs
Side Rail
#3 x 1 pc
Footboard
#A x 8 pcs
Bolt 5/16”x1”
#B x 6 pcs
Bolt 5/16”x1-5/8”
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 8 pcs
Bolt 5/16”x3-7/8”
MD
#D x 22 pcs
Flat Washer
Page 4 of 7
#E x 22 pcs
Lock Washer
#F x 13 pcs
Center Connector
#4 x 1 pc
Support Rail
#5 x 4 pcs
Foot
#6 x 26 pcs
Slat
#7 x 2 pcs
Slat Support Leg #G x 26 pcs
End Cap
#H x 1 pc
Allen Wrench

Turn right (clockwise) to tighten
Page 5 of 7
#C x 8 pcs
#D x 8 pcs
#E x 8 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.
I. Align the two feet (#5) onto the pre-drilled holes on the bottom
corners of the headboard (#1).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#C) and then the flat washer (#D) onto the
SAME bolt (#C), in that order.
III. Insert the bolt assemblies through the holes of the feet (#5) and
secure those bolts using the Allen wrench (#H) to lock them with
the headboard (#1).
IV. Repeat the process above to assemble the remaining two feet
(#5) onto the footboard (#3).

Turn right (clockwise) to tighten
Page 6 of 7
#A x 8 pcs
#D x 8 pcs
#E x 8 pcs
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
I. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt (#A)
and then the flat washer (#D)
onto the SAME bolt (#A), in
that order.
II. Insert the bolt assemblies
through the right and left side
of the pre-drilled holes of the
headboard (#1) using the
Allen wrench (#H) but expose
about ½” of the bolts’ threads.
III. Mount the brackets on the
side rails (#2) onto the bolts
(#A) on each side of the
headboard (#1). Make sure
all the washers are in the
FRONT of the brackets. Use
the Allen wrench (#H) to
further tighten the bolts to
secure the two parts together.
IV. Repeat the process above to
assemble the other ends of
the two side rails (#2) onto the
footboard (#3).
I. Align the two slat support legs (#7) with the pre-drilled holes of the support
rail (#4).
II. Prepare 2 bolt assemblies by inserting FIRST the lock washer (#E) onto the
bolt (#B) and then the flat washer (#D) onto the SAME bolt (#B), in that
order.
III. Insert the two bolt assemblies through the pre-drilled holes of the support
rail (#4) using the Allen wrench (#H) to lock them with the slat support legs
(#7).
Turn right (clockwise) to tighten
Adjust the leveler on the slat support legs (#7)
according to the ground level on Step 4.

Turn right (clockwise) to tighten
Page 7 of 7
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs I. Align the assembled
support rail (#4) with the
pre-drilled holes on the
center of the headboard
(#1) and the footboard
(#3).
II. Prepare 4 bolt assemblies
by inserting FIRST the lock
washer (#E) onto the bolt
(#B) and then the flat
washer (#D) onto the
SAME bolt (#B), in that
order.
III. Insert the 4 bolt
assemblies through the
brackets of the support rail
(#4) using the Allen wrench
(#H) to lock them with the
headboard (#1) and the
footboard (#3).
I. Prepare a complete bed slat by
inserting one center plastic
connector (#F) onto the two slats
(#6). Then insert two end caps
(#G) onto the opposite ends of the
same slats (#6).
II. Align the end caps (#G) on a
completed bed slat with the pre-
drilled holes on each side of the
side rails (#2) and snap down
both end caps (#G) into place.
Then snap down the center
plastic connector (#F) into the
support rail (#4).
III. Repeat the above process to
assemble the remaining bed slats.
ASSEMBLY IS COMPLETED
Note: The correct position of the bed
slats should be arcing UPWARD when
placing on the rails. #F x 13 pcs
#G x 26 pcs
Adjust the leveler according to the ground
level. To lower or to raise the slat support
leg, turn the leveler clockwise or
counterclockwise, respectively.