Furniture of America CM7027Q User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7027Q
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-11
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 2 pcs
Side Rail
#3 x 1 pc
Footboard
#A x 8 pcs
Bolt 5/16”x3/4”
#B x 4 pcs
Bolt 5/16”x1-1/4”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until each
step is completed or instructed.
#C x 2 pcs
Bolt 5/16”x1-3/4”
MD
#D x 4 pcs
Bolt 5/16”x2-1/2”
Page 3 of 6
#H x 30 pcs
End Cap
#6 x 30 pcs
Slat
#4 x 1 pc
Center Support Rail
#5 x 4 pcs
HB/FB Leg
#7 x 2 pcs
Support Rail Leg
#E x 18 pcs
Flat Washer
#F x 18 pcs
Lock Washer
#G x 15 pcs
Center Connector
#I x 1 pc
Allen Wrench

Turn right (clockwise) to tighten
Page 4 of 6
#D x 4 pcs
#E x 4 pcs
#F x 4 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.
I. Align the two HB/FB legs (#5) with the pre-drilled holes
underneath the headboard (#1).
II. Prepare two bolt assemblies by inserting FIRST the lock washer
(#F) onto the bolt (#D) and then the flat washer (#E) onto the
SAME bolt (#D), in that order.
III. Insert the bolt assemblies through the two HB/FB legs (#5) using
the Allen wrench (#I) to lock them with the headboard (#1).
IV. Repeat the process above to assemble the other two HB/FB legs
(#5) onto the footboard (#3).

Turn right (clockwise) to tighten
Page 5 of 6
#A x 8 pcs
#E x 8 pcs
#F x 8 pcs
#C x 2 pcs
#E x 2 pcs
#F x 2 pcs
I. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#F) onto the bolt (#A)
and then the flat washer (#E)
onto the SAME bolt (#A), in
that order.
II. Insert the bolt assemblies
through the right and left side
of the pre-drilled holes of the
headboard (#1) using the
Allen wrench (#I) but expose
about ½” of the bolts’ threads.
III. Mount the brackets on the
side rails (#2) onto the bolts
(#A) on each side of the
headboard (#1). Make sure all
the washers are in the
FRONT of the brackets. Use
the Allen wrench (#I) to further
tighten the bolts to secure the
two parts together.
IV. Repeat the process above to
assemble the other ends of
the two side rails (#2) onto the
footboard (#3).
I. Align the two support rail legs (#7) with the pre-drilled holes of the center
support rail (#4).
II. Prepare 2 bolt assemblies by inserting FIRST the lock washer (#F) onto the
bolt (#C) and then the flat washer (#E) onto the SAME bolt (#C), in that
order.
III. Insert the two bolt assemblies through the pre-drilled holes of the center
support rail (#4) using the Allen wrench (#I) to lock them with the two
support rail legs (#7). Turn right (clockwise) to tighten
Adjust the levelers on the support rail legs
(#7) according to the ground level on Step 4.

Turn right (clockwise) to tighten
Page 6 of 6
#B x 4 pcs
#E x 4 pcs
#F x 4 pcs
I. Align the assembled center support rail (#4) with the pre-drilled holes on the
center of the headboard (#1) and the footboard (#3).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#F) onto the
bolt (#B) and then the flat washer (#E) onto the SAME bolt (#B), in that
order.
III. Insert the 4 bolt assemblies through the brackets of the center support rail
(#4) using the Allen wrench (#H) to lock them with the headboard (#1) and
the footboard (#3).
I. Prepare a bed slat using 2 slats
(#6), one center connector (#G)
and two end caps (#H). See
diagram for the correct sequence in
connecting those parts.
II. Align the two end caps (#H) with
the pre-drilled holes on each side of
the side rails (#2) and press firmly
down on both end caps (#H) to lock
with the side rails (#2). Then press
firmly down on the center
connector (#G) to lock with the
center support rail (#4).
III. Repeat the process above to
assemble the remaining bed slats
onto the side rails (#2) and the
center support rail (#4).
IV. Make sure the bed is rested on a
flat surface and does not feel loose
or wobbly. If it does, double check
that the bolts/screws are secured
and properly tightened.
ASSEMBLY IS COMPLETED
Note: The correct position of the bed
slats should be arcing UPWARD when
placing on the rails.
#G x 15 pcs
#H x 30 pcs
Adjust the levelers according to the ground
level. To lower or to raise the support rail
leg, to turn the leveler clockwise or
counterclockwise, respectively.

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7027CK/EK
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-11
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 2 pcs
Side Rail
#3 x 1 pc
Footboard
#A x 8 pcs
Bolt 5/16”x3/4”
#B x 4 pcs
Bolt 5/16”x1-1/4”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until each
step is completed or instructed.
#C x 2 pcs
Bolt 5/16”x1-3/4”
MD
#D x 4 pcs
Bolt 5/16”x2-1/2”
Page 3 of 6
#H x 30 pcs
End Cap
#6 x 45 pcs
Slat
#4 x 2 pcs
Support Rail
#5 x 4 pcs
HB/FB Leg
#7 x 4 pcs
Support Rail Leg
#E x 24 pcs
Flat Washer
#F x 24 pcs
Lock Washer
#G x 30 pcs
Center Connector
#I x 1 pc
Allen Wrench

Turn right (clockwise) to tighten
Page 4 of 6
#D x 4 pcs
#E x 4 pcs
#F x 4 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.
I. Align the two HB/FB legs (#5) with the pre-drilled holes
underneath the headboard (#1).
II. Prepare two bolt assemblies by inserting FIRST the lock washer
(#F) onto the bolt (#D) and then the flat washer (#E) onto the
SAME bolt (#D), in that order.
III. Insert the bolt assemblies through the two HB/FB legs (#5) using
the Allen wrench (#I) to lock them with the headboard (#1).
IV. Repeat the process above to assemble the other two HB/FB legs
(#5) onto the footboard (#3).