Furniture of America CM-FC603 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-07-16
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
CM-FC603

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 7

Page 3 of 7

Parts List Parts List (Continued)
#1 x 1 pc
5-Star Base
#2 x 5 pcs
Caster
#3 x 1 pc
Gas Lift Cylinder
#9 x 1 pc
Headrest
#B x 4 pcs
Screw M6x30
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 6 pcs
Screw M6x35
MD
#D x 6 pcs
Flat Washer
#4 x 1 pc
Cylinder Cover
Page 4 of 7
#E x 1 pc
Knob
#5 x 1 pc
Seat Plate w/Handle
#6 x 1 pc
Backrest
#7 x 1 pc
Seat
#8 x 2 pcs
Armrest
Hardware List
#A x 4 pcs
Screw M6x20
#F x 1 pc
Allen Wrench

Turn right (clockwise) to tighten
Page 5 of 7
Insert the 5 casters (#2) into the 5-star
base (#1). Then insert the gas lift
cylinder (#3) into the 5-star base and
the cylinder cover (#4) over the gas lift
cylinder (#3).
I. Align the seat plate with handle
(#5) with the pre-drilled holes
on the bottom of the seat (#7).
II. Insert 4 screws (#A) through
the holes of the seat plate with
handle (#5) and secure those
screws using theAllen wrench
(#F) to lock them with the seat
(#7).
III. Align the two armrests (#8) with
the pre-drilled holes on the
bottom of the seat (#7).
IV. Prepare 6 screw assemblies by
inserting the flat washer (#D)
onto the screw (#C).
V. Insert the screw assemblies
through the pre-drilled holes on
the bottom of the armrest (#8)
and secure those screws using
the Allen wrench (#F) to lock
them with the seat (#7).
#A x 4 pcs
#C x 6 pcs
#D x 6 pcs

Page 6 of 7
Turn right (clockwise) to tighten
#B x 4 pcs
I. Align the backrest (#6)
with the pre-drilled holes
on the bottom of the seat
(#7).
II. Insert 4 screws (#B)
through the bottom of the
backrest (#6) using the
Allen wrench (#F) to lock
them with the seat (#7).
I. Align the headrest (#9) with
the pre-drilled hole on the
back of the backrest (#6).
II. Insert the knob (#E) through
the back of the headrest (#9)
and tighten by hand until
secure with the backrest
(#6). #6 Turn right (clockwise) to tighten
#E x 1 pc

Page 7 of 7
I. Carefully place the assembled seat plate with handle (#5)
onto the assembled gas lift cylinder (#3). Make sure the
parts are firmly secured.
II. Make sure the chair is rested on a flat surface. Check that
all parts are secured, the chair is stable and the up/down lift
is working properly.
ASSEMBLY IS COMPLETED