Furniture of America CM-BK634TT User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 9
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-06-27
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
CM-BK634TT
For more information contact our team: [email protected]

Page 2 of 9
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 9
#2 x 1pc
#3 x 1pc
#5 x 1pc
#6 x 1pc
Lower Back Side Rail
#7 x 1pc
#8 x 1pc
Upper Front Side Rail
#9 x 2pcs
Lower Front Side Rail
Upper Back Side Rail
Back Guard Rail
#10 x 2pcs
Front Guard Rail
#13 x 1pc
Ladder Post (Left)
#14 x 1pc
Ladder Post (Right)
#15 x 4pcs
Ladder Steps
#12 x 3pcs
Guard Rail Support
#11 x 2 Sets
Twin Slat (13pcs)
#1 x 1pc
Upper End Guardrail
Upper End Guardrail
Lower End Guardrail
#4 x 1pc
Lower End Guardrail

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 9
Hardware List
#A x 16 pcs
Bolt Ø5/16"x 4"
#B x 16pcs
Barel Nut Ø5/16"
#C x 9pcs
Bolt Ø1/4"x1-1/4"
#D x 52pcs
Screw #4x30mm
#E x 4pcs
Metal Dowel Ø10x3-1/2"
#F x 6pcs
Bolt Ø1/4"x1-5/8"
#G x 8pcs
Screw Ø1/4"x2"
#I x 1pc
Allen Key 4mm
#J x 12pcs
Wood Dowel Ø10x40mm
#1
#2
#3
#4
#6
#5
#7
#8
#9
#10
#11
#11
#13
#14
#15
#12
#H x 6pcs
Screw Ø1/4"x 3-1/8"

Page 5 of 9
#A
#B
#I
#3
#4
#6
#5
#9
#10
#1
#2
#A x 8pcs
#B x 8pcs
#A x 8pcs
#B x 8pcs
#H x 6pcs
#J x 12pcs
#A
#B
#I
#H
#I
#J
#8
#7
Insert barrel nuts (#B) to the side holes of the
lower side rails (#4,5). Align lower side rails
(#5,6) to the holes of the lower end guardrails
(#3,4), then secure by tightening bolts (#A) onto
barrel nuts (#B).
1) Insert dowels (#J) to guardrails (#9,10), then
insert barrel nuts (#B) to upper side rails (#7,8).
2) Align guardrails (#9,10) and upper side rails
(#7,8)to the upper end guardrails (#1,2), then
secure with screws (#H) and bolts (#A).

Page 6 of 9
#C
#I
#12
#E
#1
#2
#3
#4
#C x 9pcs
#E x 4pcs
#9
#10
#E
#8
#7
Align guardrail supports (#12) to the guardrails,
then secure by using bolts (#C).
Place metal dowels (#E) onto the holes on top of
lower end guardrails (#3,4), then carefully align upper
end guardrails (#1,2) to lower end guardrails (#3,4).

Page 7 of 9
#G
#I
#G
#15
#14
#13
#F
#13
#14
#5
#8
#10
#G x 8pcs
#F x 6pcs
#F #I
#I
Align ladder rungs (#15) to the ladder rails (#13,14), then
secure by using screws (#G).
Align ladder to the bunk bed, then
secure by using bolts (#F)

#D
#D
#D x 52pcs
#7
#11
#11
#8
#6
#5
ASSEMBLY IS COMPLETED
Page 8 of 9
Page 8 of 9Page 8 of 9Page 8 of 9
Align slat kits (#11) to the bunk beds, then
secure by using screws (#D).

Page 9of 9