Furniture of America CM7150Q User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 10
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-11-27
CM7150Q/EK/CK
Tools Required For Assembly:
For more information contact our team: [email protected]
2 PERSONS RECOMMENDED
Allen Wrench
Philip Screwdriver
(Not Included)
(Included)

BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Page 2 of 10
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Hardware List
#1 x 1pc
#2 x 1pc
#A x 1pc
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard
Page 3 of 10
Footboard
#3 x 2pcs
Rail (L&R)
#4 x 1pc
Headboard Panel
#5 x 2pcs
Ear Panel (L&R)
#6 x 2pcs
Support Bar
#7 x 2pcs
Headboard Support Rail
#8 x 11pcs
Slats
#9 x 3pcs
Slats Whit Hole
#B x 10pcs
Bolt Ø1/4" x 1-1/2"
#C x 8pcs
Bolt Ø1/4" x 3-1/2"
#D x 10pcs
Bolt Ø1/4" x 2-3/8"
#E x 4pcs
Bolt Ø1/4" x 1-3/16"
#F x 32pcs
Lock Washer Ø1/4"
#G x 14pcs
#H x 18pcs
#I x 2pcs
Anti Slip Sheet
Allen Wrench M4
Flat Washer Ø1/4" x 19mm
Flat Washer Ø1/4" x 25mm

Page 4 of 10
Parts List
Hardware List
#10 x 2pcs
#11 x 2pcs
#J x 4pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Center Rail
Footboard Leg
Screw M3 x 5/8"
#12 x 6pcs
Slat Support Leg 285x30x30mm
#13 x 2pcs
Center Rail Support
#K x 4pcs
Screw M4 x 1"
#L x 30pcs
Screw M4 x 1-3/16"
#1
#5R
#5L
#6
#7
#4
#2
#3L
#3R
#9
#8
#10 #12
#11
#11
#M x 6pcs
Screw M4 x 1-3/4"
#13

Page 5 of 10
#B x 4pcs
#F x 4pcs
#H x 4pcs
#1
#7
# A
#B
#F
#H
#B x 6pcs
#F x 6pcs
#H x 6pcs
#1
#5L
#5R
# A
#B
#F
#H
Align HB support rails (#7) to the headboard (#1), then secure by
using bolts (#B) with washers (#F,H).
Align headboard (#1) to the ear panels (#5R/L), then secure by
using bolts (#B) with washers (#F,H).

#D x 4pcs
#F x 4pcs
#G x 4pcs
#G
#F
#D
#A
#2
#13
#2
#11 #K
#I
#I x 2pcs
#K x 2pcs
Page 6 of 10
Align center rail supports (#13) to the footboard (#2), then secure
by using bolts (#D) with washers (#F,G).
Align legs (#11) with washer (#I) to the footboard (#2),
then secure by using screws (#K)
Secure only the hole
that is on footboard.

#K x 2pcs
#3R
#3L
#11
#K
# A
#E
#F
# G
Page 7 of 10
#3R
#3L
#E x 4pcs
#F x 4pcs
#G x 4pcs
#2
Align side rails (#3R/L) to the footboard (#2), then secure
by using bolts (#E) with washers (#F,G).
Secure the legs (#11) to the side rails (#3R/L) by using screws (#K).

#3R
#3L
#A
#C
#F
#H
#C x 4pcs
#F x 4pcs
#H x 4pcs
#J x 4pcs
#J
#1
#4
Page 8 of 10
#5L
#5R
#4
Align headboard ears (#5R/L) to side rails (#3R/L), then secure
by using bolts (#C) with washers (#F,H).
Align HB panel (#4) to the headboard,
then secure by using screws (#J).

#5R
#5L #6
#M
#M x 6pcs
#D x 6pcs
#F x 6pcs
#G x 6pcs
#9
#10
#12
# A
#D
#F
#G
Page 9 of 10
#A
#C #F
#H
#C x 4pcs
#F x 4pcs
#H x 4pcs
#3L
#3R
Align support bars (#6) to the bottom of the side rails (#3R/L), then secure by using screws (#M).
Secure side rails (#3R/L) to HB ears (#5R/L) by using bolts (#C) with washers (#F,H).
Align center rails (#10) to the slats (#9) and
slat support legs (#12), then secure by
using bolts (#D) with washers (#F,G).

#L x 8pcs
#L
#L
#9
#3L #2
#L x 22pcs
#L
#3L
#3R
#8
Page 10 of 10
#3R
Secure slats (#9) to side rails (#3R/L) by
using screws (#L).
Align slats (#8) to the side rails (#3R/L), then
secure by using screws (#L).