Furniture of America CM7389EK User manual

Assembly Instructions
EASY DIFFICULT
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Tools Required For Assembly:
R
R
CM7389EK
Page 1 of 7
For more information contact our team: [email protected]
2 PERSONS RECOMMENDED
Allen Wrench
(Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)
REV: 18-01-10

Page 2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
Headboard
#1 x 1pc
#2 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard Posts(L/R)
#3 x 4pcs
Bun foot
#7 x 5pcs
Slat
#8 x 10pcs Ø1/4"
Support Leg 25x32x32mm
#4 x 1pc
Footboard
#5 x 2pcs
SideRail
Page 3 of 7
#6 x 1pc
#D x 8pcs
#C x 8pcs
Flat Washer Ø5/16 x 19
Lock Washer Ø5/16 x 13
#B x 8pcs
#A x 1pc
Allen Key M4
Bolt Ø5/16 x 1-3/4"
#E x 2pcs
Thread rod Ø5/16 x 3-1/2"
#F x 2pcs
Curved Washer
#G x 2pcs
Hex Nut Φ5/16 x 16mm
#H x 1pc
Allen Wrench 12mm
#I x 10pcs
Wood Screw #8 x 25mm
Headboard Support

#2
#3
Page 4 of 7
Exploded View
#2R
#2L
#1
#3
#4
#5
#5
#6
#7
#8
X2
Attach bun foot (#3) to the holes of the headboard posts (#2).

Page 5 of 7
#H
#G
#F
#E
#1
#1
#6
#B x 6 pcs
#C x 6 pcs
#D x 6 pcs
#E x 2 pcs
#F x 2 pcs
#G x 2 pcs
#B x 2 pcs
#C x 2 pcs
#D x 2 pcs
#B
#A
#C
#D #2R
#2L
#A #C
#B
#D
1) Attach threaded bolts (#E) to the holes of the HB posts (#2R/L), then align
headboard (#1) to HB posts (#2R/L). Secure by using washer (#F) and hex nut (#G)
onto threaded bolts (#E).
2) Secure HB legs (#2R/L) to
headboard (#1) by using bolts
(#B) with washers (#C,D).
Align HB support (#6) to the holes of the headboard (#1). Secure by using bolts (#B)
with washers (#C,D).

Leveler
#7
#8
Page 6 of 7
X5
#3
#4
Attach support legs (#8) to the holes of the slats (#7), then adjust
levelers of the support legs (#8) according to ground level.
Attach bun foot (#3) to the holes of the
footboard (#4).

Page 7 of 7
#I x 10 pcs
#I
#1
#4
#5
#5
#5
#5
#7
Attach side rails (#5) by hooking side rails (#5) to the latches of the
headboard (#1) and footboard (#4). Make sure it is firmly in place.
Align slats (#7) to the side rails (#5), then secure by using screws (#I).