Furniture of America CM7129Q User manual

EASY DIFFICULT
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
CM7129Q
Page 1 of 6
Rev.16-08-05
Assembly Instructions

BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
Page 2 of 6

Parts List
Hardware List
#1 x 1 pc
#2 x 1 pc
#4 x 2 pcs
#A x 8 pcs
Bolt Ø1/4" x 2-1/2"
#B x 8 pcs
#C x 8 pcs
#D x 1 pc
Allen Wrench M4
Side Rail
Slat
Slat Support 35x35x190mm
Footboard
Headboard
#3 x 2 pcs
#6 x 3 pcs
#7 x 3 pcs Ø1/4"
Long Screw #4x1-3/8"
#E x 4 pcs
Page 3 of 6
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Flat Washer Ø1/4"
Lock Washer Ø1/4"
MD
#Fx 2 pcs
Short Screw #4x1-3/16"
#G x 6 pcs
Cover
#5 x 4 pcs
Finial
Leg (L&R)

Page 4 of 6
#1
#4R
#4L
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
Before you begin,please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#A
#D
#B #C
Align the right headboard leg (#4R) with the right side of the
headboard (#1).
Prepare 8 bolt assemblies by inserting FIRST the lock washer (#B)
onto the bolt (#A) and then the flat washer (#C) onto the SAME bolt
(#A), in that order.
Insert the bolt assemblies through the right headboard leg (#4R)
and secure those bolts using the Allen wrench (#D) to lock them in
with the headboard (#1).
Repeat process above to assemble the left headboard leg (#4L)
onto the left side of the headboard (#1).
Turnright(clockwise)totighten
Note: Right and left are determined by facing
the front of the bed in upright position.
I.
II.
III.
IV.

Page 5 of 6
#2
#1
#3
#E x 4 pcs
#F x 2 pcs
#5
#2
#1 #E
#1
#2
#5
#5 #E
#5
#F
Turnright(clockwise)totighten
Align the 2 finials (#5) onto
the top of the headboard (#1).
Secure two long screws (#E)
through the holes on the
headboard (#1) using a Phillips
screwdriver to tighten them
down to the 2 finials (#5).
Align the other 2 finials (#5)
onto the top of the footboard
(#2).
Secure two long screws (#E)
through the holes on the
footboard (#2) using a Phillips
screwdriver to tighten them
down to the 2 finials (#5). Then
place the 2 covers (#F) over
the 2 long screws (#E) on the
footboard (#2) to cover the
holes.
I.
II.
III.
IV.
Insert the hooks of
the 2 side rails (#3)
into the slotted bars of
the headboard (#1).
Make sure both parts
are secured properly.
Insert the hooks of
the other ends of the
two size rail (#3) into
the slotted bars of the
footboard (#2). Make
sure both parts are
secured properly.
I.
II.

Page 6 of 6
#G
#G x 6 pcs
#2
#3
#1
X3
#6 #7
ASSEMBLY IS COMPLETED
#6
Align the threaded end of the slat support leg (#7) with the pre-drilled
holes of the slat (#6) and tighten by hand until secured. Repeat the
process for the remaining 2 slat support legs (#7). onto the 2 slats (#6).
Turnright(clockwise)totighten
Turnright(clockwise)totighten
Align the ends of the
assembled slat (#6) with
the pre-drilled holes on
each side of the side rails
(#3). Secure two short
screws (#G) onto each
end of the slat (#6) using
a Phillips screwdriver to
tighten them down to the
side rails (#3). Repeat the
process for the remaining
three slats (#6).

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7129CK
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-11-26
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Phillips Screwdriver
(Not Included)

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 1 pc
Footboard
#3 x 2 pcs
Side Rail
#A x 8 pcs
Bolt 1/4”x2-1/2”
#B x 8 pcs
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 8 pcs
Flat Washer
MD
#D x 1 pc
Allen Wrench
#4R x 1 pc
Right H/B Leg
Page 3 of 6
#E x 4 pcs
Long Screw
#F x 2 pcs
Cover
#4L x 1 pc
Left H/B Leg
#5 x 4 pcs
Finial
#6 x 4 pcs
Slat
#7 x 8 pcs
Slat Support Leg
#G x 8 pcs
Short Screw

Page 4 of 6
Turn right (clockwise) to tighten
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling
of the product to avoid any potential injury and/or
damage.
I. Align the right headboard leg (#4R) with the right side of the
headboard (#1).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through the right headboard leg (#4R)
and secure those bolts using the Allen wrench (#D) to lock them
in with the headboard (#1).
IV. Repeat process above to assemble the left headboard leg (#4L)
onto the left side of the headboard (#1).
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
#4L
#4R
Note: Right and left are determined by facing the
front of the bed in upright position.