Furniture of America CM7568Q User manual

AssemblyInstructions
EASY DIFFICULT
Page 1 of6
ASSEMBLYRATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product(with 1 being
easy and 5 being difficult).For some
products,two persons are recommended.
CM7568Q/EK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
For more information contact our team: [email protected]
Phillips Screwdriver
(Not Included)
AssemblyInstructions
EASY DIFFICULT
Page 1 of 7
ASSEMBLYRATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product(with 1 being
easy and 5 being difficult).For some
products,two persons are recommended.
CM7568CK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
For more information contact our team: [email protected]
Phillips Screwdriver
(Not Included)
Rev: 19-07-10
Rev: 19-07-10

Page2 of 6
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.
Page2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Hardware List
#2 x 2pcs
#G x 1pc
#A x 6pcs
#B x 6pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page3 of 6
Headboard Leg(L&R)
Allen Key4mm
Bolt Ø5/16" x 1-1/2"
Lock Washer Ø5/16"
#C x 6pcs
Flat Washer Ø5/16"
#1 x 1pc
Headboard
#6 x 2pcs
Side Rail
#7 x 1set
Bed Slat (13pcs)
#3 x 1pc
Footboard
#5 x 2pcsØ1/4"
FBSupport Leg164x30x30mm
#H x 26pcs
Screw #8 x 32mm
#8 x 1pc
Center Slat
#D x 2pcs
#E x 2pcs
Bolt Ø1/4" x 1"
Lock Washer Ø1/4"
#F x 2pcs
Flat Washer Ø1/4"
#4 x 2pcs Ø1/4"
FB Leg Ø110x84m m
Parts List
Hardware List
#2 x 2pcs
#G x 1pc
#A x 6pcs
#B x 6pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page3 of 7
Headboard Leg(L&R)
Allen Key4mm
Bolt Ø5/16" x 1-1/2"
Lock Washer Ø5/16"
#C x 6pcs
Flat Washer Ø5/16"
#1 x 1pc
Headboard
#6 x 2pcs
Side Rail
#7 x 1set
Bed Slat (13pcs)
#3 x 1pc
Footboard
#5 x 2pcsØ1/4"
FBSupport Leg164x30x30mm
#H x 26pcs
Screw #8 x 32mm
#8 x 1pc
Center Slat
#D x 2pcs
#E x 2pcs
Bolt Ø5/16" x 1"
Lock Washer Ø1/4"
#F x 2pcs
Flat Washer Ø1/4"
#4 x 2pcs Ø1/4"
FB Leg Ø110x84m m

#9 x 1pcØ1/4"
Short Support Leg
115 x30x30mm
Page4 of 6
#10 x 3pcsØ1/4"
Long Support Leg 362x30x30mm
#A x 6pcs
#B x6pcs
#C x6pcs
#6
#5
#7
#9
#10 #8
Parts List
#1
#2L
#2R
#3
#4
#A#B#C
#G
#2R
#2L
#1
Page4 of7
#6
#5
#7
#9
#10 #8
#1
#2L
#2R
#3
#4
Parts List
Hardware List
#J x 10pcs
Bolt Ø1/4" x 1-1/2"
#9 x 1pcØ1/4"
Short Support Leg 115 x30x30mm
#10 x 3pcsØ1/4"
Long Support Leg 362x30x30mm
#11 x 2pcs
Top Side Rail
#11
#11
Align HB legs (#2R/L) to the headboard (#1), then
secure by using bolts (#A) with washers (#B,C).

Page5 of 6
#5
#5
#5
#A x 6pcs
#B x6pcs
#C x6pcs
#3
#1
#3
Page5 of 7
#4
#5
#3
#4
#A#B#C
#G
#2R
#2L
#1
Attach FB legs (#4) to the footboard (#3), then attach
support leg (#5) to footboard (#3).
Align and hook the side rails (#5) to the headboard (#1) and
footboard (#3). Make sure it is firmly in place.

Page6 of 6
Adjust leveler
#9
#10
#8
Page6 of 7
#5
#5
#1
#3
Adjust leveler
#9
#10
#8
#H x 26pcs #H
#D
#E
#F
#G
#D x 2pcs
#E x 2pcs
#F x 2pcs
#9
#10
#8
#5
#5
#7
#9
#10
#8
Attach support legs (#9,10) to the center support rail (#8), then adjust
leveler of the support legs (#10) according to ground level.
Align slats (#7) to side rails, then secure by using screws (#H).
Align center slat (#8) to the slats
(#7), then secure by using bolts
(#D) with washers (#E,F)