Furniture of America CM7673Q User manual

Rev: 16-06-15

Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
HeadboardPanel
#3 x 1pc
#6 x 4pcs
#5 x 1pc
Page3 of 6
#4 x 2pcs
HB Leg / Right
Footboard
Side Rail
Bed Slat
Headboard Support
#8 x 2pcs
Footboard Leg
Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
HeadboardPanel
#3 x 1pc
#6 x 3pcs
#7 x 3pcs Ø1/4"
#5 x 1pc
Page3 of 6
#4 x 2pcs
HB Leg / Right
Footboard
Side Rail
Bed Slat
Headboard Support
Rail Support Leg
30 x 30 x 187mm
#8 x 2pcs
Footboard Legs
#E x 6pcs
#A x 8pcs
Bolt Ø5/16" x 1-3/4"
#B x 10pcs
#C x 10pcs
Lock Washer Ø5/16"
Flat Washer
Ø5/16"
#D x 1pc
#F x 8pcs
#G x 8pcs
#H x 1pc
Screw Ø4 x 1-3/16"
Allen Key 4mm
Threaded Stud Ø5/16" x 3-1/2"
Hex Nut
Ø5/16"
Wrench 14mm
#7 x 3pcs Ø1/4"
Rail Support Leg
30 x 30 x 187mm
#I x 2pcs
Bolt Ø1/4" x 1-3/4"
#E x 6pcs
#A x 8pcs
Bolt Ø5/16" x 1-3/4"
#B x 10pcs
#C x 10pcs
Lock Washer Ø5/16"
Flat Washer
Ø5/16"
#D x 1pc
#F x 8pcs
#G x 8pcs
#H x 1pc
Screw Ø4 x 1-3/16"
Allen Key 4mm
Threaded Stud Ø5/16" x 3-1/2"
Hex Nut
Ø5/16"
Wrench 14mm
#I x 2pcs
Bolt Ø1/4" x 1-3/4"

8
10
10
#I x 2pcs
1. Prepare 4 bolt assemblies by first inserting a lock washer (#B) onto the bolt (#I)
then a flat washer (#C) onto that same bolt (#I). Align the headboard support
(#5) to the holes along the legs, then insert the bolts into each end. Secure.
2. Prepare 8 bolt assemblies by
first inserting a lock washer
(#B) onto the bolt (#A) then a
flat washer (#C) onto that same
bolt (#A). Align the legs (#2) to
the holes along the headboard
(#1), then insert the bolts. Secure
using the Allen wrench. (#D).
Insert the threaded ends of the footboard
legs (#8) into the holes along the bottom
of the footboard (#3), turn right to tighten.

1. Insert the threaded studs (#F) into the holes along the head-
board (#1) and footboard (#3). Turn right to tighten.
2. Place the side rails
(#4) onto those
threaded studs (#F),
then apply the hex
nut (#G) from within.
Secure using the
wrench (#H).
Insert the threaded ends of the support legs (#7) into
the holes along the slats (#6), turn right to tighten.
Adjust according to
the ground level.

Place the slats (#6) onto the rails, then insert a screw
(#E) into each end. Secure using a screwdriver.

Rev: 16-06-15

Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
HeadboardPanel
#3 x 1pc
#6 x 4pcs
#5 x 1pc
Page3 of 6
#4 x 2pcs
HB Leg / Right
Footboard
Side Rail
Bed Slat
Headboard Support
#8 x 2pcs
Footboard Leg
#7 x 8pcs Ø1/4"
Rail Support Leg
30 x 30 x 1537mm
#E x 6pcs
#A x 8pcs
Bolt Ø5/16" x 1-3/4"
#B x 10pcs
#C x 10pcs
Lock Washer Ø5/16"
Flat Washer
Ø5/16"
#D x 1pc
#F x 8pcs
#G x 8pcs
#H x 1pc
Screw Ø4 x 1-3/16"
Allen Key 4mm
Threaded Stud Ø5/16" x 3-1/2"
Hex Nut
Ø5/16"
Wrench 14mm
#I x 2pcs
Bolt Ø1/4" x 1-3/4"

8
10
10
#I x 2pcs
1. Prepare 4 bolt assemblies by first inserting a lock washer (#B) onto the bolt (#I)
then a flat washer (#C) onto that same bolt (#I). Align the headboard support
(#5) to the holes along the legs, then insert the bolts into each end. Secure.
2. Prepare 8 bolt assemblies by
first inserting a lock washer
(#B) onto the bolt (#A) then a
flat washer (#C) onto that same
bolt (#A). Align the legs (#2) to
the holes along the headboard
(#1), then insert the bolts. Secure
using the Allen wrench. (#D).
Insert the threaded ends of the footboard
legs (#8) into the holes along the bottom
of the footboard (#3), turn right to tighten.