Furniture of America HFW-1697C6-TR User manual

2 / 19
Prep Time!
Please review the assembly instructions and all
diagrams prior to assembling. Arrange parts as
recommended on Page 7 and group identical
hardware together to make assembling easier.
Check out our Quick Tips!
We recommend reviewing the pre-assembly
handouts. Even experts need a refresher now and
then!
Are you missing anything?
Double-check all parts, hardware and
accessories listed are all accounted
for.
Should we send any replacements?
Are there any irregularities or flaws in the
parts? We can send replacements!
CHECK
BEFORE STARTING

PRE ASSEMBLY
INTRODUCTION
3 / 19
Suitable Location
Assembling near the area of the
intended location is highly
recommended.
Avoid Scratches
Use cardboard, blankets or a
carpeted area while assembling
furniture to prevent scratches.
Teamwork
ALWAYS have at least two people
to help with transporting and
assembling the product to avoid
potential injury and/or damage.
Flat Surface
Make sure the furniture rests on
a flat and level surface with each
leg evenly touching the floor.
Sufficient Space
Make sure you have enough
space to move around during the
assembly.
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.

IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE HARDWARE MAY LOOSEN
OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS
INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY.
Turn clockwise to tighten and
only tighten when step is
completed or when instructed
to do so.
Use the appropriate hand tools
or power tools for assembly.
Select steps, such as tightening
screws and/or bolts, may require
hand tools to avoid causing
damage during assembly.
Position each part correctly
and insert screws or bolts into
their respective holes.
Save the instructions and store
any supplied tools for later
maintenance.
After two weeks, check and
tighten any loose hardware and
repeat again every six months
thereafter.
4 / 19
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
ASSEMBLY
AND
CARE ADVICE

5 / 19
Note :
Every cam lock bolt must have a cam
lock connector in order to fasten the
parts together.
CAM LOCK FASTENER
ASSEMBLY
INSTRUCTIONS
cam bolt cam lock screwdriver
4
Turn the cam lock clockwise gently
until it will not turn any more.
2
Insert the cam bolt into the
bolt hole of joint panel.
3
Align the cam lock with its side opening
(or arrow) pointing to cam bolt.
1
Screw the cam
bolt into panel.

6 / 19
PARTS
HARDWARE
TOWER CABINET
1PC
A
1A1
ACCESSORIES
A
22PCS 22PCS
242PCS 3
62SETS1SET
4PCS
4
5 7 1SET
0.7"
(8x30)
A3
A2
2PCS
A4
22PCS 1PC
3SETS
1PC
A5
1PC
B
1PC
E
1PC
C1PCD2PCS F
1PC
G
2PCS
H
2PCSI
1PC
J
1PCL
1PCM1PC
N
1PC
O
1PCK1PC
P1PC
Q
D
K
J
L
2.2"
spring
1.2"
4PCS
8
10 8SETS4PCS
9
0.8"
1SET
A6
0.5" 1.2"
1PC
R

Must have a dab of glue (#A1) onto these
two dowels (#3).

Note: Wooden dowels (#3) on panel
(#R) should be facing forward.

1. Align drawer to the product.
2. Insert the drawer at an angle.
Ensure that the back drawer panel is
behind dowels (#3).
3. Once aligned, slided drawer
straight in.

ASSEMBLY
COMPLETED
Please ensure the
furniture rests on an even
and flat surface. If the
product wobbles or feels
loose, double-check all
bolts and/or screws are
properly tightened and
secured.
Keep this handy!
Please retain this instruction
manual and any order-related
information for future reference.
Lift, don’t drag!
To avoid damage to product
please always LIFT the product
when transporting of adjusting
the placement.


19/ 19