Furniture of America CM7725CK User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 7
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 16-11-28
CM7725CK/EK/Q/F
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)
For more information contact our team: [email protected]

Page 2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 1pc
#4 x 2pcs
#A x 4pcs
Bolt Ø5/16" x 2"
#B x 4pcs
#C x 4pcs
#D x 6pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard Panel
#3 x 2pcs
#5 x 1pc
#6 x 1pc
#7 x 24pcs
#8 x 3pcs Ø1/4"
Page 3 of 7
Lock Washer Ø5/16"
Flat Washer Ø5/16"
Bolt Ø1/4" x 1-3/8"
Footboard
Bed Rail
Headboard Leg (L&R)
Leg Support
Center Rail
Bed Slat
Support Leg 30x30x325mm
#E x 4pcs
#F x 4pcs
Lock Washer Ø1/4"
Flat Washer Ø1/4"
#G x 8pcs
#H x 8pcs
Thread bolt Ø5/16" x 3-1/8"
Curve washer Ø5/16"

Hardware List
#M x 12pcs
#N x 24pcs
#K x 1pc
Open Wrench
#L x 1pc
#O x 1pc
Page 4 of 7
Allen Wrench
# A x 4pcs
#B x 4pcs
# C x 4pcs
#D x 4pcs
#E x 4pcs
#F x 4pcs
#C#B
#A
#L
# 5
# 4R
#1
# 4L
Slats connector
End Cap
U wood bar
#I x 8pcs
#J x 2pcs
Hex nut Ø5/16" x 3/4"
Screw #4 x 1-1/4"
#F
#E
#D
#L
Prepare 4 bolts assembly by inserting lock washer (#B), then flat washer (#C) onto bolts (#A).
Align headboard legs (#4R/L) to the holes of the headboard (#1). Secure with bolts (#A).
Prepare 4 bolts assembly by inserting lock washer
(#E), then flat washer (#F) onto bolts (#D). Align
headboard legs (#4R/L) to the holes of the leg
support (#5). Secure with bolts (#D).

Page 5 of 7
#1
# 3
# 3
# 2
#G
#H
#I
#K
# G x 8pcs
#H x 8pcs
#I x 8pcs
# 8 # 6
1) Attach the thread bolts (#G) to the headboard (#1)
and footboard (#2). Place curve washer (#H), then hex
nut (#I) into the bolts of the bed rails (#3).
2) Align thread bolt (#G) to the
holes of the curve washer (#H)
and hex nut (#I), then secure by
using the wrench (#K).
Attach 3 support legs (#8) to the center slat (#6). Adjust floor protector according to ground level.

Page 6 of 7
#D
#L
#D x 2pcs
# O x 1pc
# 2
# O
# J x 2pcs
# 6
#J
# 5
# 2
Align U wood bar (#O) to the holes of the footboard (#2). Secure with bolts (#D).
Place center slat (#6) onto the U wood bars,
then secure with screws (#J).

Page 7 of 7
# 7
# 7
#M
# 6
#N
# 7
# 3
# 3
# 7
ASSEMBLY IS COMPLETED
# 3
#M x 12pcs
#N x 24pcs
Attach 1 end cap (#N) to each bed slat (#7), then connect two slats (#7) using slat connectors (#M).
Secure by pushing in the caps (#M,N) to the holes of the rails (#3,6).