Furniture of America Lincoln Park CM4702-3PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-07-15
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
CM4702-3PK
Phillips Screwdriver (Not Included)
2 PERSONS RECOMMENDED

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 7

Page 3 of 7

Parts List Hardware List
#1 x 1 pc
Coffee Table Top
#2 x 1 pc
Coffee Table Shelf
#3R x 2 pcs
C. Table Right Leg
#A x 24 pcs
Bolt 5/16”x50
#B x 24 pcs
Lock Washer
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 24 pcs
Flat Washer
MD
#D x 12 pcs
Screw M4x30
#3L x 2 pcs
C. Table Left Leg
Page 4 of 7
#E x 1 pc
Allen Wrench
#4 x 2 pcs
End Table Top
#5 x 2 pcs
End Table Shelf
#6R x 4 pcs
E. Table Right Leg
#6L x 4 pcs
E. Table Left Leg

Page 5 of 7
Due to the size and/or weight of this product, it
is highly recommended that the assembly
should be done near the area of its intended
location. Make sure you have enough space to
move around during the assembly. ALWAYS
have at least two people to help with
transporting and assembling the product to
avoid any potential injury and/or damage.
Note: Right and left are
determined by facing the front of
the fully-assembled table.

Page 6 of 7
I. Carefully place the coffee table
top (#1) facing down on a
protected surface. Align the two
right legs (#3R) with the pre-
drilled holes on the right corners
of the coffee table top (#1).
II. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then
the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies
through the pre-drilled holes on
the right corners of the coffee
table top (#1) and secure those
bolts using the Allen wrench (#E)
to lock them with the right legs
(#3R).
IV. Repeat the process above to
assemble the two left legs (#3L)
onto the coffee table top (#1).
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. Align the coffee table shelf (#2)
with the pre-drilled holes on the
right legs (#3R) and the left
legs (#3L).
II. Insert 4 screws (#D) into the
coffee table shelf (#2) using the
Phillips screwdriver to lock
them with the right legs (#3R)
and the left legs (#3L).
III. Carefully turn the completed
table upright. Make sure the
table is rested on a flat surface
and does not feel loose or
wobbly. If it does, double
check that the bolts are
secured and properly tightened.
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
#D x 4 pcs
#3L
#3R

Page 7 of 7
I. Carefully place the end table top
(#4) facing down on a protected
surface. Align the two right legs
(#6R) with the pre-drilled holes
on the right corners of the end
table top (#4).
II. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then
the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies
through the pre-drilled holes on
the right corners of the end table
top (#4) and secure those bolts
using theAllen wrench (#E) to
lock them with the right legs
(#6R).
IV. Repeat the process above to
assemble the two left legs (#6L)
onto the end table top (#4).
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. Align the end table shelf (#5)
with the pre-drilled holes on the
right legs (#6R) and the left
legs (#6L).
II. Insert 4 screws (#D) into the
end table shelf (#5) using the
Phillips screwdriver to lock
them with the right legs (#6R)
and the left legs (#6L).
III. Carefully turn the completed
table upright. Make sure the
table is rested on a flat surface
and does not feel loose or
wobbly. If it does, double
check that the bolts are
secured and properly tightened.
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
#D x 4 pcs
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND END TABLE.
#6R
#6L