Furniture of America CM7941F User manual

EASY
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some products,
two persons are recommended.
Page 1 of 5
Assembly Instructions
DIFFICULT
2 PERSONS RECOMMENDED
REV: 16 -10 -27
Tools Required For Assembly:
CM7941F
Allen Wrench (Included)
Phillips Screwdriver (Not Included)

Page
2 of 5
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY
CAUSE SERIOUS INJURY.
When lock or spring washer is used
in an assembly, please make sure
the lock or spring washer is placed
between the larger flat washer and
the head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the
Allen wrench or any supplied tool for
later maintenance. After two weeks,
check and tighten any loose
hardware and repeat again every six
months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Parts List Hardware List
#1 x 1pc
Headboard
#2 x 1pc
Left H/Board Leg
Page
3 of 5
#3 x 1pc
Right H/Board Leg
#D x 1pc
Allen Wrench
#A x 6pcs
Bolt 5/16 x 1-3/8"
#B x 6pcs
Look Washer
#C x 6pcs
Flat Washer
D:\CONG VIEC\7941\1.jpg
#4 x 1pc
Footboard
#5 x 2pcs
Side Rail
#6 x 4pcs
Slat
#E x 8pcs
Screw
#7 x 4pcs
Slat Support Leg

Page
4 of 5
#A x 6pcs
#B x 6pcs
#C x 6pcs
I. Align the left HB leg (#2) with the
pre-drilled holes of the headboard
(#1).
II. Prepare 3 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then
the flat washer (#B) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through
the left HB leg (#2) using the Allen
wrench (#D) to lock them with the
headboard (#1).
IV. Repeat the process above to
assemble the right HB leg (#3)
onto the headboard (#1). Note: Right and left
are determined by
facing the FRONT
of the bed in its
upright position.
Turn right (clockwise) to tighten
I. Insert the hooks of the two side
rails (#5) into the slotted bars of
the headboard (#1). Make sure
the parts are secured properly.
II. Insert the hooks on the other ends
of the two side rails (#5) into the
slotted bars of the footboard (#4).
Make sure the parts are secured
properly.
#1
#3
#2
#D #A #B #C
#1
#5
#4
#5
#5

Page
5 of 5
ASSEMBLY IS COMPLETED
Adjust the leveler according to the
ground level on Step 4.
Align the threaded end of the slat support leg (#7) with the pre-drilled
hole of the slat (#6) and tighten by hand until secured. Repeat the
process to assemble the remaining 3 slat support legs (#7) onto the 3
slats (#6)
Turn right (clockwise) to tighten
#E x 8pcs
I. Align the ends of the assembled slat (#6) with the pre-drilled holes on
each side of the side rails (#5).
II. Secure two screws (#E) onto the ends of the slat (#6) by using a
Phillips screwdriver to tighten them down to the side rails (#5).
III. Repeat the process to assemble the remaining 3 assembled slats
(#6) onto the side rails (#5).
Adjust the leveler according to the
ground level. To lower or to raise the
slat support leg, you need to turn the
leveler clockwise or counterclockwise,
respectively.
X4
#6
#6
#7
Turn right (clockwise) to tighten
#1
#4
#5
#E
#6
#5