Furniture of America Woodmont CM3663AC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3663AC-2PK
For more information contact our team: [email protected]
Rev:18-07-27

BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.
Page 2 of 5

Parts List Hardware List (Continued)
#1 x 4 pcs
Front Leg
#2 x 2 pcs
Seat
#3 x 2 pcs
Backrest w/ Legs
#A x 8 pcs
Bolt 1/4”x1-3/8”
#B x 2 pcs
Bolt 5/16”x1-1/2”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until each
step is completed or instructed.
#C x 8 pcs
Bolt 5/16”x2”
#D x 8 pcs
Bolt 5/16”x3”
Page 3 of 5
#F x 18 pcs
Flat Washer 5/16”
#E x 18 pcs
Lock Washer 5/16”
#5 x 2 pcs
Right Armrest
#J x 4 pcs
Flat Washer 1/4”
#G x 1 pc
Allen Wrench
#I x 8 pcs
Lock Washer 1/4”
Hardware List
#4 x 2 pcs
Left Armrest
#H x 4 pcs
Bolt Cover

I. Place the backrest with legs (#3) on a protected surface.Align
the seat (#2) with the pre-drilled holes of the backrest with legs
(#3).
II. Prepare a bolt assembly by inserting FIRST the lock washer
(#E) onto the bolt (#B) and then the flat washer (#F) onto the
SAME bolt (#B), in that order.
III. Insert the bolt assembly through the pre-drilled hole on the
center of the seat (#2) and secure that bolt using the Allen
wrench (#G) to lock it with the backrest with legs (#3).
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 4 of 5
#B x 2 pcs
#E x 2 pcs
#F x 2 pcs
#D x 8 pcs
#E x 8 pcs
#F x 8 pcs
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#D) and then the flat washer (#F) onto the
SAME bolt (#D), in that order.
II. Insert the bolt assemblies through the pre-drilled holes in the
corners of the seat (#2) and secure those bolts using theAllen
wrench (#G) to lock them with the backrest with legs (#3).
X 2
X 2

Turn right (clockwise) to tighten
Page 5 of 5
#C x 8 pcs
#E x 8 pcs
#F x 8 pcs
I. Align the 2 front legs (#1) with the pre-drilled holes on the corners of the seat
(#2).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#E) onto the
bolt (#C) and then the flat washer (#F) onto the SAME bolt (#C), in that order.
X 2
ASSEMBLY IS COMPLETED
X 2
Note: Right and left are determined by standing
behind the chair in the upright position.
I. Align the left armrest (#4) with the pre-
drilled holes of the backrest with legs
(#3) AND the seat (#2).
II. Prepare a bolt assembly by inserting
FIRST the lock washer (#I) onto the
bolt (#A) and then the flat washer (#J)
onto the SAME bolt (#A), in that order.
V. Repeat the process above to assemble
the right armrest (#5) onto the backrest
with legs (#3) AND the seat (#2).
VI. Make sure the chair is rested on a flat
surface and does not feel loose or
wobbly. If it does, double check that the
bolts are secured and properly
tightened.
#A x 8 pcs
#H x 4 pcs
#I x 8 pcs
#J x 4 pcs
#5
#2
III. Insert the bolt assemblies through the pre-drilled holes in the corners of the
seat (#2) and secure those bolts using the Allen wrench (#G) to lock them
with the two front legs (#1).
III. Insert that bolt assembly through the
seat (#2) and secure that bolt using the
Allen wrench (#G) to lock it with the
lower left armrest (#4).
IV. Prepare a bolt assembly by inserting
the lock washer (#I) onto the bolt (#A).
Insert that bolt assembly through the
backrest with legs (#3) using the Allen
wrench (#G) to lock it with the upper left
arm (#4). Once tighten, place the bolt
cover (#H) over the bolt.