Furniture of America YNJ-2052C25 User manual

EASY DIFFICULT
1 / 21
MODEL #
Questions?
GIVE US A CALL: 1-888-980-5122
MON－FRI 8:30AM－5:30PM (PST)
TOOLS REQUIRED
ASSEMBLY RATING
2 - People
Recommended
The Assembly Rating is a
level of effort needed to
assemble a specific product.
5-point system showing the
VERSION # 20-10-19
YNJ-2052C25
YNJ-2052C31
YNJ-2052C35
Phillips
Screwdriver
(Not Included)
(Not Included)
Hammer

2 / 21

3 / 21

4 / 21
AND MAY CAUSE SERIOUS INJURY.
ASSEMBLY
CARE ADVICE
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
Position each part correctly
and insert screws or bolts into
their respective holes.
Select steps, such as tightening
screws and/or bolts, may require
hand tools to avoid causing
damage during assembly.
Use the appropriate hand tools
or power tools for assembly.
Turn clockwise to tighten and
only tighten when step is
completed or when instructed
to do so.
Save the instructions and store
any supplied tools for later
maintenance.
After two weeks, check and
tighten any loose hardware and
repeat again every six months
thereafter.

5 / 21

P1PC
O1PC
N2PCS
M1PC
L1PC
K1PC
J2PCS
I1PC
H1PC
G2PCS
F1PC
E1PC
D1PC
C1PC
B1PC
1PC
A
YNJ-2052C25
YNJ-2052C31
YNJ-2052C35
DESK
PARTS
HARDWARE ACCESSORIES
6 / 21
120PCS 220PCS 412PCS 54PCS
76PCS 812PCS 62PCS
37PCS
92PCS
0.59"
1.97"
0.59"
1"
2PCS
A1 1PC
A3 14PCS
A4
1PC
A5
2SETS
A2
10 2PCS
T3PCS
S2PCS
R1PC
Q4PCS
0.31"
1.38"
X1PC
W2PCS
V1PC
U2PCS

7 / 21
GET READY
Please group boards as below.
Body
M1PC F1PC E1PC
D1PC C1PC B1PC1PC A
L1PC
K1PC
J2PCS
I1PC H1PC G2PCS
P1PC T3PCS R1PC Q4PCS
X1PC W2PCS V1PC
O1PC N2PCS S2PCS U2PCS

8 / 21
1
Hardware x8PCS
1
Hardware x7PCS
3
Accessory x1PC
A5
OPTIONAL
Apply a dab of glue
into dowel holes of
panels before
inserting dowels (#3).
3
A5
A
3
3
1
1
B
1
1
1
C
1
1
1
E
3
3
3
GX2

9 / 21
2
Hardware x12PCS
1
H
1
1
1
K
1
1
1
I
1
11
L
1
11
3
Part x1PC
A
Accessory x1PC
A3
Part x1PC
F
Hardware x2PCS
4
or
A3
Recommend using a power
tool to only tighten
hardware (#4) faster.
Accessory (#A3) could also
work for hardware (#4) if a
power tool is not present.
RECOMMEND
Front
Top
4
4
A
F
hole facing to bottom

10 / 21
4
5
Part x1PC
E
Part x1PC
B
Hardware x8PCS
2
Part x1PC
D
Accessory x1PC
A3
Part x1PC
M
Hardware x6PCS
4
Part x1PC
C
Please refer to page 5 for
detailed instructions on
how to fasten cam locks
(#2) to cam bolts (#1).
1
2
Accessory x2PCS
A4
Use the provided stickers
(#A4) to cover exposed
locks. X2
or
A3
Recommend using a power
tool to only tighten
hardware (#4) faster.
Accessory (#A3) could also
work for hardware (#4) if a
power tool is not present.
RECOMMEND
Front
Top
Front
Top
4
4
4
4
4
4
D
M
C
2
2
2
B
C
E
F
2
2
2
2
A
2

11 / 21
6
7
Accessory x1PC
A3
Accessory x6PCS
A4
Part x2PCS
G
Hardware x6PCS
2
Hardware x4PCS
4
or
A3
Recommend using a power
tool to only tighten
hardware (#4) faster.
Accessory (#A3) could also
work for hardware (#4) if a
power tool is not present.
RECOMMEND
1
2
Part x1PC
K
Part x1PC
L
Part x2PCS
J
X2
4
4
G
J
Front
Top
Front
Top
2
2
2
G
K
L
22
2
J
Flip
90°
X6
Use the provided stickers
(#A4) to cover exposed
locks/screws.
hole facing to bottom

12 / 21
8
9
Hardware x2PCS
7
Accessory x2PCS
A1
Accessory x6PCS
A4
Hardware x6PCS
2
1
2
Part x1PC
H
Part x1PC
I
Front
Top
Front
Top
Align the iron pieces (#A1) to panel (#G),
then secure by using screws (#7). There
will be no pre-drilled holes so the iron
pieces (#A1) can be aligned at any
distance from each other. Please refer
page 21 to decide the position of iron
pieces (#A1).
7
A1
X2
G
2
2
2
G
22
2
J
H
I
X6
Use the provided stickers
(#A4) to cover exposed
locks/screws.

13 / 21
10
Part x1PC
V
Part x4PCS
Q
W
Q
Q
W
Front
Top
T
X
V
T
Q
T
Q
V
Part x3PCS
T
Part x1PC
X
Part x2PCS
W
Please ensure that the hole on
part (#W) is facing inwards as
shown in the diagram.
Ensure all parts are attached with the
same orientation as the diagram.

14 / 21
11
12
Part x1PC
P
Part x1PC
R
Front
Top
Part x1PC
O
Part x2PCS
UFront
Top
O
U
U
R
P
T
Ensure all parts are attached with the
same orientation as the diagram.

15 / 21
13
Part x2PCS
N
The concave hole on part (#N)
is aligned and facing inwards
towards each other as shown
in the arrows in the diagram.
The hole on part (#U)
should be facing down as
shown by the arrow in the
diagram.
Front
Top
X2
6
Hardware x2PCS
6
N
N
U
U
W
N
W
N
Ensure all parts are attached with the
same orientation as the diagram.

16 / 21
14
15
Part x2PCS
S
Hardware x2PCS
9
Hardware x2PCS
10
Front
Top
X2
S
N
N
N
1st 2nd X2
10
9S
Front
Top
Ensure all parts are attached with the
same orientation as the diagram.

17 / 21
16
Accessory x1PC
A3
Hardware x4PCS
7
Hardware x12PCS
8
C
I
L
Front
Top
7
7
77
Secure by using bolts (#8) and
screws (#7) in order as shown in
the diagram.
7th
A3
C
I
L
8
8
8
8
8
8
8
8
88
8
8
1st
2nd
3rd
4th
5th
6th
B
H
K

18 / 21
17
Align the product to the wall,
then mark the wall with a pencil
according to how you want to
orient the product.
Flip 180°
Front
Top
Hardware x4PCS
5
5
5
X2
U
18 Top
50.69"
The dimension is for reference,
the dimension after the actual
assembly shall prevail.

19 / 21
19
Use power drill (not included) to drill
holes onto the marks on the wall.
Please refer to page 21
on wall mounts.
Front
Top
Accessory x2SETS
A2
X2
A2
Secureunitontothewallby
usingscrews (#A2). Please
ensurethattheunitis
properlyalignedtothewall.
Refer to page 21 on wall
mounting guide.
20

20 / 21
21
Keep this handy!
Please retain this instruction
manual and any order-related
information for future reference.
Please ensure the
furniture rests on an even
and flat surface. If the
produst wobbles or feels
loose,double-check all
bolts and/or screws are
properly tightened and
secured.
ASSEMBLY
COMPLETED
Lift, dont drag!
To avoid damage to product
please always LIFT the product
when transporting of adjusting
the placement.