Furuno 1824C User manual

24+06'& ޓ +0 ޓ ,#2#0
MODEL 1824C MARINE RADAR
MODEL 1834C MARINE RADAR
MODEL 1934C MARINE RADAR
MODEL 1944C MARINE RADAR
MODEL 1954C MARINE RADAR
GD-1920C COLOR VIDEO PLOTTER
VX2

6JGRCRGTWUGFKPVJKUOCPWCN
KUGNGOGPVCNEJNQTKPGHTGG
Your Local Agent/DealerYour Local Agent/Dealer
9-52 Ashihara-cho,9-52 Ashihara-cho,
Nishinomi
y
a 662-8580, JAPANNishinomi
y
a 662-8580, JAPAN
Tele
p
hone :Tele
p
hone : 0798-65-21110798-65-2111
FaxFax 0798-65-42000798-65-4200
::
F
IRST EDITION :
F
IRST EDITION : FEBFEB.. 20052005
Printed in JapanPrinted in Japan
A
ll ri
g
hts reserved.
A
ll ri
g
hts reserved.
Pub. No.Pub. No. IME-35430-AIME-35430-A
*
00015180300
*
*
00015180300
*
*
00015180300
*
*
00015180300
*
(( DAMIDAMI )) MODEL1804C_GD-1920CMODEL1804C_GD-1920C * 0 0 0 1 5 1 8 0 3 0 0 ** 0 0 0 1 5 1 8 0 3 0 0 *
*
IME
35430
A
00
*
*
IME
35430
A
00
*
*
IME
35430
A
00
*
*
IME
35430
A
00
*
* I M E 3 5 4 3 0 A 0 0 ** I M E 3 5 4 3 0 A 0 0 *

i
WARNING
Radio Frequency
Radiation Hazard
The radar antenna emits electromagnetic
radio frequency (RF) energy which can be
harmful, particularly to your eyes. Never
look directly into the antenna aperture from
a close distance while the radar is in
operation or expose yourself to the trans-
mitting antenna at a close distance.
Distances at which RF radiation levels of
100 and 10 W/m2exist are given in the
table below.
Note: If the antenna unit is installed at a
close distance in front of the wheel house,
your administration may require halt of
transmission within a certain sector of
antenna revolution. This is possible - Ask
your FURUNO representative or dealer to
provide this feature.
MODEL
Distance to
100 W/m
2
point
Distance to
10 W/m
2
point
MODEL
1834C Nil Worst case
1.80 m
SAFETY INSTRUCTIONS
Do not open the equipment
unless totally familiar with
electrical circuits and
service manual.
Only qualified personnel
should work inside the
equipment.
Wear a safety belt and hard
hat when working on the
antenna unit.
Serious injury or death can
result if someone falls from
the radar mast.
WARNING
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if some-
one falls from the radar mast.
Turn off the power at the mains switch-
board before beginning the installation.
Fire, electrical shock or serious injury can
result if the power is left on or is applied
while the equipment is being installed.
ELECTRICAL
SHOCK
HAZARD
MODEL
1934C
MODEL
1944C
Worst case
3.00 m
Nil Worst case
2.50 m
Observe the following compass safe
distances to prevent deviation of a
magnetic compass.
Standard Steering
Display unit
MODEL1834C antenna unit
MODEL1934C antenna unit
MODEL1944C antenna unit
0.70 m 0.45 m
0.90 m 0.70 m
1.00 m
1.00 m 0.80 m
0.80 m
CAUTION
Ground the equipment to
prevent electrical shock and
mutual interference.
MODEL1954C antenna unit
1.00 m 0.75 m
MODEL
1954C
XN12A
XN13A Nil
Worst case
2.50 m
Worst case
2.30 m
Power supply unit (1954C)
1.40 m 0.95 m
MODEL1824C antenna unit
1.25 m 0.85 m
MODEL
1824C Nil Worst case
0.50 m
Worst case
0.20 m

ii
TABLE OF CONTENTS
EQUIPMENT LISTS ............................................................................................. iii
SYSTEM CONFIGURATIONS .............................................................................. v
1. MOUNTING ................................................................................................... 1-1
1.1 Mounting the Display Unit....................................................................................................1-1
1.2 Mounting the Antenna Unit of MODEL1824C ..................................................................... 1-4
1.3 Mounting the Antenna Unit of MODEL1834C ................................................................... 1-12
1.4 Mounting the Antenna Unit of MODEL1934C/1944C/1954C............................................ 1-17
1.5 Mounting the Power Supply Unit of MODEL1954C .......................................................... 1-26
2. WIRING.......................................................................................................... 2-1
2.1 Standard Wiring ................................................................................................................... 2-1
2.2 External Buzzer (optional supply)........................................................................................ 2-4
2.3 How to Connect with a PC................................................................................................... 2-5
2.4 Wiring the Power Supply Unit for MODEL1954C................................................................ 2-6
3. SETTING UP THE EQUIPMENT................................................................... 3-1
3.1 Setting up with the Installation Wizard ................................................................................ 3-1
3.2 Checking Magnetron Heater Voltage ................................................................................ 3-13
3.3 Remote Controller Setting ................................................................................................. 3-13
4. OPTIONAL EQUIPMENT .............................................................................. 4-1
4.1 ARP Kit ARP-11 ................................................................................................................... 4-1
4.2 Connection of Video Equipment/External Monitor/Remote Display.................................... 4-4
PACKING LISTS ............................................................................................... A-1
OUTLINE DRAWINGS ...................................................................................... D-1
INTERCONNECTION DIAGRAMS ....................................................................S-1

iii
EQUIPMENT LISTS
Standard supply
Name Type Code No. Qty Remarks
Display unit RDP-149 - 1
RSB-0094-075 - MODEL 1824C
RSB-0071-057 - MODEL 1834C
XN10A-RSB-0070-064 - MODEL1934C, 24 rpm
XN10A-RSB-0073-064 - MODEL1934C, 48 rpm
XN12A-RSB-0070-059 - MODEL1944C, 24 rpm
XN12A-RSB-0073-059 - MODEL1944C, 48 rpm
XN12A-RSB-0072-060 - MODEL1954C, 4”, 24 rpm
XN12A-RSB-0073-060 - MODEL1954C, 4”, 48 rpm
Antenna unit
XN13A-RSB-0072-060 -
1
MODEL1954C, 6”, 24 rpm
Power supply unit PSU-005 - 1 For MODEL1954C
Remote controller
set RMC-100 000-089-885 1
Remote controller, vinyl case,
battery, labels
CP03-22700 000-080-049 1set
For display unit,
MJ-A3SPF0018-050Z cable,
CP03-22701
CP03-21800 000-080-014
For MODEL1824C/1834C
10 m signal cable
CP03-21810 000-080-015
For MODEL1824C/1834C
15 m signal cable
CP03-21820 000-080-016
For MODEL1824C/1834C
20 m signal cable
CP03-21830 000-080-017
1
For MODEL1824C/1834C
30 m signal cable
CP03-22000 000-080-021
For 1934C/1944C/1954C
10 m signal cable
CP03-22010 000-080-022
For 1934C/1944C/1954C
15 m signal cable
CP03-22020 000-080-023
For 1934C/1944C/1954C
20 m signal cable
CP03-22030 000-080-024
1
For 1934C/1944C/1954C
30 m signal cable
Installation
materials
CP03-24501 000-080-191 1 For 1954C, power supply unit
SP03-14001 000-080-018 1set Fuses for display unit
Spare parts SP03-14001 000-080-018 1set Fuses for 1954C’s power supply
unit

iv
Optional supply
Name Type Code No. Qty Remarks
000-013-484 For GD-1920C, 100 VAC
000-013-485 For GD-1920C, 110 VAC
000-013-486 For GD-1920C, 220 VAC
PR-62
000-013-487
1
For GD-1920C, 230 VAC
Rectifier
RU-3423 000-030-443 1 For MODEL series
External
buzzer
OP03-136 000-086-443 1
MJ-A6SPF0014-010 000-144-421 1 For NavNet, 1 m
MJ-A6SPF0014-050 000-144-422 1 For NavNet, 5 m
MJ-A6SPF0014-100 000-144-423 1 For NavNet, 10 m
MJ-A6SPF0014-200 000-144-424 1 For NavNet, 20 m
MJ-A6SPF0014-300 000-144-425 1 For NavNet, 30 m
MJ-A6SPF0012-050 000-134-424 1 For navaid, 5 m
MJ-A6SPF0012-100 000-133-817 1 For navaid, 10 m
MJ-A6SPF0003-050 000-117-603 1 w/6P connector, 5 m
MJ-A6SPF0009-100 000-125-236 1 w/6P connector, 10 m
MJ-A6SPF0007-100 000-125-237 1 For compass, 10 m
MJ-A7SPF0007-050 000-144-418 1
For external buzzer, PC,
w/7P connector, 5 m
MJ-A6SRMD/TM11AP8-
005
000-144-463 1 Adapter cable for HUB
MJ-B24LPF0008-100 000-145-125 1 For remote display,
10 m
MJ-B24LPF0008-200 000-145-126 1 For remote display,
20 m
Cable assy.
MJ-B24LPF0008-300 000-145-127 1 For remote display,
30 m
With
CP03-
24801
(EMI core)
Remote
controller set RMC-100 000-089-885 1
Remote controller, vinyl case,
battery, labels
RGB output
cable kit OP03-176 008-526-360 1 For external monitor
ARP kit ARP-11 008-523-050 1 ARP Board, for radar
PIP kit OP03-175 008-523-070 1 Connection video source
Chart card - - - Specify when ordering.
Mounting
bracket (1) OP03-92 008-445-070 1 For MODEL1834C
Mounting
bracket (2) OP03-93 008-445-080 1 For MODEL1824C

v
SYSTEM CONFIGURATIONS
All NavNet products incorporate a “network circuit board” to integrate each NavNet product
on board through an optional LAN cable (Ethernet 10BASE-T). Each NavNet product is
assigned an IP address to enable transfer of images between other NavNet products. For
example, video plotter pictures can be transferred to a radar and vice versa. Pictures
received via the NavNet may be adjusted at the receiving end.
The number of display units which may be installed depends on the number of network
sounders connected. For a system incorporating three or more NavNet products, a “hub” is
required to process data.
For one network sounder: one radar and three plotters, or four plotters
For two network sounders: one radar and two plotters, or four plotters
External buzzer
PC
Heading sensor
Rectifier
RU-3423
Echo sounder
Navigator
GPS receiver
GP-310B/320B
12 - 24 VDC*
Network
Sounder
ETR-6/10N
ETR-30N
Other NavNet unit
(GD-1920C, etc.)
Antenna Unit
MODEL
1834C
MODEL
1934C
MODEL
1944C
Display unit
RDP-149
100/110/115/220/230 VAC
1φ, 50/60 Hz*
VGA monitor
Remote display
Video equipment
MODEL
1954C
Power Supply
Unit PSU-005
*: The power for the power supply unit
and display unit must be drawn from
the same power source.
Facsimile
Receiver
FAX-30
MODEL1824C
ARPA
ARP-11
: Standard
: Option
: Local supply
NavNet system: MODEL1824C/1834C/1934C/1944C/1954C

vi
Network
Sounder
ETR-6/10N
ETR-30N
GPS receiver
GP-310B/320B
12 - 24 VDC
Other NavNet Unit
(Model 1834C, etc.)
Display unit
RDP-149
100/110/115/220/230 VAC
1φ, 50/60 Hz
Remote
Controller
RMC-100
External buzzer
Echo sounder
Navigator
Rectifier
PR-62
VGA monitor
Remote display
PC
Video equipment
Facsimile
Receiver
FAX-30
ARPA
ARP-11
: Standard
: Option
: Local supply
NavNet system: GD-1920C

vii
Radar Antenna Unit
OR
GPS Receiver GP-310B/320B
Radar, plotter data
Radar, plotter data
Radar Antenna Unit
OR
GPS Receiver GP-310B/320B
RADAR
or
PLOTTER
RADAR
or
PLOTTER
Two-unit NavNet system
HUB
Network Sounder
ETR-6/10N
ETR-30N
(option)
Radar Antenna Unit
OR
GPS Receiver GP-310B/320B
Radar Antenna Unit
OR
GPS Receiver GP-310B/320B
RADAR
or
PLOTTER
RADAR
or
PLOTTER
Sounder data
Radar data Plotter data
Note:Thepicturedisappears
10secondsaftertheNavNet
cableisdisconnectedfroma
"sub"NavNetdisplayunit.
Network Sounder
ETR-6/10N
ETR-30N
(option)
Facsimile
Receiver
FAX-30
(option)
Sounder data
Facsimile
data
Three-or-more unit NavNet system

viii
This page intentionally left blank.