Futuro Futuro Folio Instruction Manual

Futuro Futuro
Folio
Designer Range Hood
Installation & User’s Manual

<O
'
'
'
'
'
'
'
6”
6” diam.
6” diam.
6” diam.
4.13”
Overall Dimensions
20.7”
4.1”
General Components Location
11.3” min. 12”
15.79”
13.75”
11.3” 14.3”
0.4”
20”
33.5”
4.2” 16”
27.6”
Weight: 55 lbs. (25 kg)
Must be attached to
load-bearing component
(joist/frame/plywood),
NOT to bare sheetrock.
Duct Output Collar
Locations:
Top or Rear
0.4”
Mounting Bracket & Hooks

Ducted installation - vertical blower output
18” 11.3”
Mounting, Part I:
It is recommended for the center of the range hood
to be approximately 26” - 28” above the cooktop,
for best capture performance.
1.) Measure 16”-18” from the cooktop to the bottom
of the hood.
2.) Remove the mounting bracket from the hood, position
it on the wall, and ensure it’s level.
3.) Mark the location of the mounting screws. Note that
these LOAD-BEARING screws should be connected to
a stud, framework, or 3/4” plywood - NOT to bare sheetrock.
4.) Attach the bracket to the wall.
Mounting, Part II:
1-3.) Open the bottom panel, if installed, and remove the
metal lters, if present. Locate 2 the security L-brackets on top,
unscrew & remove them.
4.) Hang the range hood on the mounting bracket, making sure
to engage BOTH mounting hooks.
5.) If adjustment is necessary, each mounting hook has 2
adjustment screws - the upper screw (B) controls distance from
wall, the lower screw (C) controls vertical adjustment.
6.) Find the 2 security L-brackets that were removed
during Step 1-3, install them on top of the hood body,
and secure them to the wall.

Backdraft Damper Installation
A backdraft damper is supplied with the range hood.
For DUCTED installation, it’s strongly recommended to DISCARD this damper, and use a damper built into the
end-cap (wall or roof cap).
For DUCTLESS installation: insert the damper as shown into the blower output collar, open the blades, and secure
the damper with the provided screw.4.) Attach the bracket to the wall.

V7
(x6) _
\ 0 ~
'" ,: ,
®
i
Ducted installation - rear (horizontal) blower output
18” 11.3”
Mounting, Part I:
It is recommended for the center of the range hood
to be approximately 26” - 28” above the cooktop,
for best capture performance.
1.) Measure 16”-18” from the cooktop to the bottom
of the hood.
2.) Remove the mounting bracket from the hood, position
it on the wall, and ensure it’s level.
3.) Mark the location of the mounting screws. Note that
these LOAD-BEARING screws should be connected to
a stud, framework, or 3/4” plywood - NOT to bare sheetrock.
4.) Attach the bracket to the wall.
Mounting, Part II: Blower Removal
1-2.) Remove the indicated screws & remove bottom panel.
3-4.) Remove the indicated screws & remove top panel.
5.) Disconnect the control panel cable from blower.
6.) Disconnect the power cable from the blower.
7.) Disconnect the grounding wire from the hood backplate.
8.) Remove the 6 screws holding the blower.
Blower Motor Removal

vs
i (x2) T j
i !/
' "
' ' .
' '
' '
' '
J;
Ducted installation - rear (horizontal) blower output
Blower Motor Repositioning
Remove the blower, remove the knock-out plate (1), and re-install the blower in new direction,
repeating the steps described on the previous page in reverse.

ON
Bottom Panel Operation
Filters Installation
Metal Mesh Filters Carbon (charcoal) Filters
For ducted AND ductless installation ONLY for DUCTLESS installation

SAFETY INSTRUCTIONS
AND WARNINGS
& Installation
operations are to be carried out by skilled and qualified in-
stallers in accordance with the instruct i ons in thisbooklet and in compli-
ance wi th the regulations in force.
DO NOT use the hood ifthe power supply cable or other components are damaged:
di sco nn ect the hood fro m the electr ica lpowersup pl ya nd con tact the D ea ler or an author-
i
se d Se r vici ng Deale rfor re pa ir s.
Do not modify the electrical. mechanical or functional structure ofthe equipment.
Do not personally try to carry out repairs or replacements . Interventions carried out
by incompetent and unauthorised persons can cause serious damage to the unit or
phys i cal and personal harm , not covered by the Manufacturer's warranty.
WARNINGS FOR THE INSTALLER
TECHNICAL SAFETY
A.
£ll
Before installing the hood, check the integrity and function of each part.
Should anomalies be noted, do not proceed with installation and contact
the Dealer.
Do NOT install the hood if an aesthetic (or cosmetic) defect has been detected. Put it
back into its original package and contact the dealer.
No claim can be made for aesthetic (or cosmetic) defects once it has been installed.
Du ri ng i nsta ll at i on, al ways u se per sona lprotective eq ui pment (e . g.: Safety sh oes) an d adopt
prudent a
nd pr ope r co nduc t.
The in st al lation ki t (screws an d pl u gs) su ppl ied wi th thehood is o nl yto be u sed onm asonry
wal l s: in case ofi ns ta ll ati on on wa l ls of adi ffe rent m ate ri al, assess oth er in st al l at ion opti ons
k ee pi ng in mi nd th et ype of wa ll surf ace and the we ightofthe hood (indi ca ted on page 2).
K eep in m in d th at in stal lations wi th di ffe rent types of f asteni ng syste ms fr om th ose sup-
pl ied, orwhich are not co mp li an t, ca n ca u se electri ca l and m echanica l sea l danger.
Do not in stal lt he hood ou tdoorsa nd do not ex p ose it toat mos p he r ic el eme nts(r ain, wind,
et
c.).
ELECTRICAL SAFETY
Befo re in sta lli ng the h oo d,ch eck th at the el ec tri ca l ma in spower su pply co rr espo n ds with
wh
at is reported on theidentification pl ate located insi de the hood.
The soc ket u se d to con nect the in stal led eq ui pm ent to the elect ri ca l power sup pl y mu st
bewi th in r each: otherwi se, in stal la m ai nsswitch to di sco nnect the hood when r equi r ed.
Any cha n ges to the elect ri cal syste m mu st beca rri ed out by a qua li fi ed electr ic i an .
The m ax imum len gt h of the fiue faste nin g s cr ews (s up pli ed by the ma nu facturer) mu st be
13mm.U
se ofnon-compliant sc r ews with th ese instructi ons can lea d toda ng er of an el ec -
tr
ica l nat ur e.
Do nottryto
so l ve the problem yo ur se lfinthe eve nt of eq uipment malfunction,but co ntact
theD
ea leror an autho ri se d Se rvici ng D epa rt me nt fo rrepair s.
A.
£ll
When installing the hood, disconnect the equipment by removing the
plug or switching off the main switch.
FUMES DISCHARGE SAFETY
A. Do no connect the equipment to discharge pipes of fumes produced from
combustion (for example boilers, fireplaces, etc .). £ll
Befo rei nsta ll in gthe hood, ensure that al l sta nd ar ds in fo r ce r ega rd in g di sc har ge ofa ir ou t of
th e roo m have b een co mpl ied with.
USER WARNINGS
These warnings have been drawn up for your personal safety and those of
others. You are therefore kindly asked to read the booklet carefully in its
entirety before using the or cleaning the equipment.
The Manufacturer declines all responsibility for any damage caused directly, or in-
directly, to
persons, things and pets as a consequence offailing to comply with the
safety warnings indicated in this booklet.
It
is imperative that this instructions booklet is kept together with the equipment for
any future consultation.
If the equipment is so ld or tr ansfer r ed to another person, make su re that the booklet is
also supp li ed so thatt he new u se r ca n be m ade awa re of the hood's ope ration and relative
wa rn ings.
Afte r the sta in le ss stee l h ood h as b ee n i nsta ll ed, it wil l n ee d to be cle a ned to rem ove any
r es i dues remain in g fro mtheprotectionadh es ive as we ll as any g re ase andoil stai nswhich,if
not rem
ove d, ca n ca u se ir r ev er s ib le da m age to theh ood s ur face . To prop er ly clea nthe un it,
the m an ufact ur er r eco mmends us in g the sup pl ied moi st wipes, w hi ch ar e al so avai l ab le
so ld se p arate l y.
I ns i st on or ig in alsp are pa r ts .
INTENDED USE
The equipment is solely intended to be used to extract fumesgenerated from cook -
ing food in non-professional domestic kitchens: any other use is improper. Improper
use can cause damage to persons, things, pets and exempts the Manufacturer from
any liability.
T he equipment can be u sed by ch il dren over the age of 8 an d by pe r so ns wi th red u ced
p hysica l, senso ry an d m enta l ab iliti es, or with no expe ri en ce or knowledg e, as long asth ey
do so und er supervisi on or after havi ng rece i ved relat i ve in st ru ctions rega rdi ng sa fe use of
the
eq ui pme nt and u ndersta ndi ng of the d angers con nected to i t.
Children ar e not to pl ay with theequi pm en t. Cl ean in g an d m ai nten anc e by the u se r m ust
not be ca rried out by chi ldren without su pe rvi sio n.
USE AND CLEANING WARNINGS
&
Before cleaning or carrying out maintenance operations, di sconnect the
equipment
by removing the plug or switching offthe main switch .
. Do not u
se t he hood wi th wet ha nd s or ba refe et.
Al ways ch ec k that a ll el ec tri cal par ts (light s, ex tr ac tor fa n) ar e off when the eq uipm en t is
not
be ing used .
T
he m axim um overa ll we ight of any o bj ec ts pl aced orhu ng (ifappl ica b le) onthe hood m ust
not exceed 1 .5 Kg.
Al ways su pe rvi se the cooking pr ocess duri ng the u se of d eep -fr ye rs: Overheated o il can
catch fire .
Do not l
eave open, unattended fia m es un de r th e hood.
Do not prepare food ove ranopen fi ame under theh ood .
N
eve r use the hood without the metal an t i- gr ease fil te r s: in th is case, gre a se a nd dirt w il l
dep
os it inthe equipment a nd co mpro mi se i ts ope ration.
Accessi bl e pa rtsof the h oo d can be hot when u se d at the sa me time as the cooki ng ap-
pli an ces .
Do not
car ryout any clea ni ng op erat i ons when par ts of the hood are st ill h ot.
The re ca n be a r is k of fire if clea nin g is not ca rri ed out acco r di ng to t he ins truct ions a nd
productsindi ca ted inthisboo kl e t.
Di sco nnect the ma in sw i tc hwh en the equ ipment isnotu se d fo rl ong pe ri ods oft im e.
& Ifother
appliances that use gas or other fuels are being used at the same
time (boiler, stove, fireplaces, etc.), make sure the room where the fumes
are discharged is well -ventilated, in compliance with the local regulations.
INSTALLATION
only intended for qualified personnel
A. Before installing the hood, carefully read the chapter ' SAFETY IN-
STRUCTIONS AND WARNINGS'. £ll
TECHNICAL FEATURES
Th etech ni ca l spec ificationsare exh ibi te d on the l abe ls locate d i nside the h oo d.
POSITIONING
The minimum distance between the highest part ofthe cooking equipment and the
lowest partofthe hood is indicated in the installation instructions .
Genera ll y, when th e hood isp lace d ove r gas cooker s, the distan ce must be at l eas t 65 cm
(25. 6 ") . However, accord i ng to an inter preta tion of st an dard EN 60335 -2-31 dated 11 -07 -
20 02 of TC61 (sub -cl au se 7. 12 .1 mee ting 15 a genda item 10. 11 ), the minimum dist ance
bet ween the cooker an d lower pa rt of t he ho od c an be r educed to t he quota reported in
th e installation in struction s.
Sho u ld the i ns tructi ons fo r th e gas cooke r specify a gre at er dis tan ce, th is mu st be tak en
into cons id e rati on .
Do not i
nsta ll th e h oo d outdoorsand do not expose it to outdoor env i ro nm en t (ra in ,wind,
etc.).
The electric circuit to which the hood is to be connected
must be:
* In compliance with local electrical standards,
* Properly grounded,
* Dedicated, not shared with other appliances or dimmable lights.

ELECTRICAL CONNECTION
(only intended for qualified personnel)
A
£ll
Disconnect the equipment from electrical mains power supply before carry-
ing out any operations on the hood.
Ensure thatthe wires inside the hood are not disconnected or cut:
in the event of damage, contact your nearest Servicing Department.
Refer to qualified personnel for electrical connections.
Connection must be carried out in compliance with the provisions of law in force.
Before connecting the hood tothe elec tr ica l ma i ns power supp l y, check th a t:
vo lta ge supply corresponds with wha t isreported on the data plate l oca t ed i ns id ethe
hood;
th eelectri cal sys t em is compliant and can with stand the lo ad (see t he t ec h nical speci fi-
cations locate d in s id ethe hood);
the power supp ly plug and cab ledo not come into contact with temperatur es exceed-
ing 10°c;
the power supply sys t em is effecti vely and proper ly connected to earth in comp lian ce
with r egu lat io ns in force;
th e socket used to connect the hood iswith in reac h.
FUMES DISCHARGE
EXTERNAL EXHAUST HOOD (SUCTION)
Inthis version the fumes a nd vapours are discharged outside through
the
exhaust pipe.
To this end, the hood outlet fitting must be con nected via a pipe, to an
ex t erna loutput.
HOOD WITH INTERNAL RECIRCULATION (FILTERING)
Inthis model,the ai r passes through the ch arcoa l filtersto be puri fi ed
and r ecycled in the environment.
Ensure that the active ca rb on filt ers are assembled into the h ood, ifnot,
in sta ll them as indicated in the assembly ins tr uctions.
A
£ll
Inthis version the chec k valve must not be assemb l ed: remove it ifit is on the air
outlet fitting ofthe motor.
ASSEMBLY INSTRUCTIONS
only intended for personnel qualified
&
The hood can be installed in various configurations.
The generic assembly steps apply to all installations ; for each case , follow
the
specific steps provided for the required installation.
OPERATION
WHEN TO TURN ON THE HOOD?
Switch on the hood at le ast one mi nute befo re sta rting to cook to direct fumes and vapours
towards the suction
surface .
After
cook in g, l eave the hood operating until complete extract io nofall vapours and odours.
By me ans ofthe Timer function, it is possible to set auto sw itch-offfunctionwhi ch w il la ll ow
the hood to turn offautomatica
ll yafter 15minutes of operation.
WHICH SPEED IS TO BE SELECTED?
1st speed : ma i nta i ns the cir cu lation of clean air with lowelectricity consumpti on.
2nd speed: normal condit ions ofu se.
3rd speed : presence of st rong odours and vapou r s.
4th speed: ra pid disposa l of odours and vapou r s.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
Th e meta lfilters must be cl eaned every 30 hours ofoperation.
The active carbon fil ters must be replaced every 3-4 months, depending on th e use of the
hood.
Forfurther details see the "MAINTENANCE" chap .
ELECTRONIC PUSHBUTTON PANEL
i
❖
+
-
~
\ ~ /
=- -
I I \ \'
~
-
~
y 11
Motor ON/OFF
Upon start -u p, the speed is that stored at the pr evious operation.
+ 11 11 11 i
T he spee ds are i ndica ted by the LEDs
on the keys:
Increase speed from 1to 4
Speed 4 iso nl y active for afew mi n-
utes, then speed 3 activates.
+ + -
i=]t=) -
Speed 1
+ + -
c=] --
Speed 2
+ + -
---
Speed 3
Reduce speed from 4 to 1 \ + ' + -
=-- --
/J 11'
Speed 4
(" +" LED flash i ng)
Light on/off
TIMER (red LED fl ashing)
Auto sw itch-offafter 15 min.
Th efunction de~es (r ed LED off) if:
-
The TIM ER key ~.' is pressed again.
- The ON/OFF key is pressed.
FILTER ALARM (red LED steady on with (+,off)
Anti-g~se fi lter maintenance after approximately 30 hours ofoperation.
Press '··-' the me te r fo r3 seco nd sto reset.
The duct (air pipe) must have:
* A diameter of 6” throughout its entire run, including the end-cap (roof or wall cap).
* A slight slope downward in horizontal sections - to prevent condensation from
dripping back into the blower motor.
* Minimum number of angles & elbows, to minimize turbulence and loss of suction.
* Minimum required length to avoid vibrations / turbulence, which can affect
the performance of the hood as well as user’s comfort level.

MAINTENANCE
&
Before cleaning or carrying out maintenance operations, disconnect the
equipment
by removing the plug or switching offthe main switch.
Do not use detergents containing abrasive, acidic or corrosive substances
or abrasive cloths.
Regu la r maintenance guarantees proper operation and performance over time.
Special attention
is to be paid to the metal anti-grease filters :frequent cleaning of the
filters and the ir supports ensures that no fiammable grease is accumulated.
CLEANING OF EXTERNAL SURFACES
Yo u are advised to clean the external surfaces of the hoo d at least once every 15 days to
preve nt oily substances and grease from sticking to them. To clean the brushed stainless
steel hood,
the Manufacturer recommends using "Magic Steel" wipes.
Alternatively
and for all the other types of surfaces , it can be cleaned using a damp cloth,
slightly moistened
with mild, liquid detergent or denatured alcohol.
&
Complete cleaning by rinsing
we ll and drying with soft cloths.
Do not use too much moisture or water around the push button control
panel and lighting devices in order to prevent humidity from reaching
electronic parts.
The glass panels can only be cleaned with specific, non-corrosive or non-abrasive deter-
gents
usi ng a soft cloth.
The Manufacturer declines
all responsibility for failure to comply with these inst ru ct ions.
CLEANING OF INTERNAL SURFACES
&
Do not clean electrical parts, or parts related tothe motor inside the hood,
with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to frequently wash the metal filters (at least once a month) lea ving them to
soak in boiling water and cleaning solution for 1hour, taking care not to bend the m.
Do
not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in adishwasher
is permitted, ho wever, it may cause the filter material to darken: to
reduce the poss ib il ity of th is problem from happening, use low - tempe ra ture washes (55°(
max.).
To extract and insert the metal anti-grease filters see the assembly ins truct ions.
ACTIVE CARBON FILTERS
These filters retain the odours in the air that passes through them.The purified air is recircu-
lated
into the environment.
The active carbon filters must be replaced
on average every 3-4 months under normal con-
ditions
of use.
See assembly ins truct io ns to replace the active carbon filters.
LIGHTING
The range hood is equipped with high efficiency, low consumption LED spotlights wi th an
extremely long life-span under normal us e conditions.
Should
the LED spotlight need to be replaced, proceed as shown in the figure.
0~
12V
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out tra sh or refuse bin symbol on the appliance means that the
product
is WEEE, i.e. "Waste electrical and electronic equipment", accordinglyit
must not be disposed ofwith regular unsorted waste (i.e. with "mixed ho use -
hold waste"),
but it must be disposed of separately so that it can undergo specif-
ic processing for its re -us e, or a specific treatment, to remove and safely dispose of any
substances
that may be harmful to the environmentand remove the ra w materials that can
be recycled.
Pr oper disposal of these products contributes to saving valuable resources and
avoid potential negative effects on personal health and
the environment, which may be
caused by inappropriate disposal
of waste.
You are kindly asked to contact your local authorities for further information regarding the
designated waste collection poin ts nearest to you. Pena lt ies for imp ro per disposal of such
waste can be applied in compliance with national regulatio
ns.
-
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directivewas implemented differentlyin each country, accordingly, if you wish
to dispose of this appliance we suggest contacting your local authorities or dealer to find
out what the correct method of disposal is .
INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES
The crossed -out trash or refuse bin symbol is only valid in the European Union: if you wish
to dispose of th is appliance in othercountries, we suggest contacting your local authorities
or dealer
to find out what the correct method of disposal is.
& WARNING!
The Manufacturer reserves the right to make changes to the equipment at any time and
without prior notice. Pr inting, translation and reproduction, even part ia l, of this manual are
bound by the Manufacturer's authorisation.
Technical information, graphic representations and specifications in this manual are for in-
formation purposes and cannot be divulged.
Th is manual is written in Itali an. The Manufacturer is not responsible for any transcription
or translation errors.