Fuze FUZE-03 User manual

User Manual
Please read the manual carefully before using Fuze Card
FUZE-03
Safety Caution
Features and Role of Fuze CardFeatures and Role of Fuze Card Features and Role of Fuze Card
01 02
0403 05
<eCHARGER>
eCHARGER can double as a portable charger for your Fuze Card with built-in battery.
❶ Card charging slot
❷ LED
❹ Charging eCHARGER terminal
❸ Power button
❷ Ear Jack
❶ Power/Change the selection(Left)
❷ Hold the current card
Change the selection(Right)
❸ Change the Mode
• Do not place heavy objects on top of Fuze Card.
• Do not deliberately bend the card. Parts inside could get damaged.
• Keep Fuze Card away from flammable sources.
• Keep Fuze Card away from water, alcohol and Benzene etc.
• Keep Fuze Card away from humid and dusty conditions.
• Keep Fuze Card away from magnetic products.
• Do not disassemble or modify Fuze Card on your own.
• To dispose of Fuze Card, cut along the dotted lines on back side of product.
• Keep Fuze Card in its charging eCHARGER while updating firmware.
• Do not use Fuze Card in humid places. (eg.Sauna, Spa)
• Sign your signature on Fuze Card with an oil-based pen.
• In low temperature conditions, the display may show a slight after image.
• The magnetic stripe emulation component meets international standard ISO 7816.
• Fuze Card may not be compatible with some POS depending on its terminal type.
• Fuze Card may not be compatible with some POS that are compliant with JIS X6302.
<Fuze Card>
❶ Recharging
terminal
Battery charging
terminal
❸ Buttons
Power on/off, change
and select credit card,
membership and
barcode etc
Place Fuze Card in slot to charge
Press and Hold down button to turn ON/OFF the card.
Simply press button to select card to the left.
❷ Display
Show selected
credit card,
membership,
barcode and
battery condition
Press and Hold down button to lock current card
on the display .
Simply press button to select card to the right.
Press and hold down button to go into multi display
Change the payment and membership type by
simply pressing the button.
Battery status
indication
Power on/off
charging eCHARGER
Charging cable slot
<Card Reader>
Front Back Side
Back
❶ Card swipe slot
<Please note that the functionality of the control buttons may be changed after you upgrade the software.
For more information about buttons and display, please check our website or App.>
Follow the instructions in the eCARD Manager App
and swipe the card on the magnetic stripe.
1. Download the App, eCARD Manager, from the Google Play or App Store.
2. Open the eCARD Manager and follow instructions to register.
3. Power on Fuze Card and connect with the App.
4. Fuze Card is ready for use now.
*** If you can’t connect Fuze Card with your smartphone restart the App.
Connect with eCARD Manager 07
1) Insert Fuze Card into the charging eCHARGER and push
the power button on the eCHARGER. A LED light will turn on
when it starts to charge.
2) The light will change color to indicate charging level.
* Charge eCHARGER using a standard micro-USB charging cable.
* LED light (Green) will turn off 15seconds after it is fully charged.
LED Status
Red Charging
Green Fully Charged
Orange Error
06 08
1) Insert the card reader 2) Add your Card
Insert the card reader into the
Ear jack port and start your App.
You can find more information on eCARD Manager.
Follow the detailed instructions carefully when
registering your Fuze Card.
EMV chip side
Magnetic stripe side
How to charge Fuze Card How to Add a Payment / Membership Card
*** Please maximize the media volume of your smartphone when registering the card. ***
BrilliantTS Co., Ltd., All Rights Reserved.
Getting started with Fuze Card
Download and install the eCARD Manager App from the Google Play Store
or iOS App Store onto your smartphone and follow the instructions.
* To use Fuze Card M Type on POS terminals with EMV chip reader, first insert Fuze Card into EMV chip reader then
swipe the magnetic stripe on POS.
• First create an account on eCARD Manager App/Website then turn the card on by pressing the
power button once. (http://www.brilliantts.com)
• Please check Fuze Card and charging eCHARGER’s battery levels and fully charge before using them.
• Please make sure Fuze Card is in its charging eCHARGER during firmware updates and turned on.
• Always have Fuze Card in its charging eCHARGER when updating.
*M Ttype is available
for magnetic stripes,
barcodes exclude
EMV chip.
*A Type is available
for magnetic stripes,
barcodes include
EMV chip.
<Fuze Card M Type> <Fuze Card A Type>

Item standard and specification
• Battery will last longer with proper care and maintenance.
• Long periods of non-use may result in a decrease of battery life span.
• Keep product away from temperatures over 35°C (95°F) and under -5°C (23°F).
• To maximize battery capacity, use in room temperature.
• Using the product in low temperatures may result in less battery life .
Other instructions
• This is a electro magnetic compatible product. It is a home electronic device and it can be used anywhere
in the world.
• This is device uses wireless equipment. During the operation, it may have electrical wave interference so
it should not be used for life-saving related services.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
• NOTE : This equipment has been tested and found to comply with the limits for a Class B, Digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide Reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, witch can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
Safety information
•Service Center [email protected]om
•Fuze Website http://www.fuzecard.com
You can find more information on the website
Sevice Center
1009 11
Button Guide
Hold for 3 sec
Single Press
Hold both
buttons for 3 sec
Fuze Card group selection
(payment / membership)
Left
Power
Right
Hold mode Multi display
(payment + membership)
Magnetic wave
FUZE Card Information
▶ Power on
Press to turn
the power on
Press to toggle
between two card groups
▶
Card group selection
(payment/membership)
POWERHOLD MULTI
CHRIS KIM
VISA
03 / 05
POWER HOLD MULTI
WALMART
05 / 05
MEMBERSHIP
VISA
03 / 05
POWER HOLDMULTI POWER HOLD MULTI
VISA
03 / 05
POWER HOLD MULTI
WALMART
05 / 05
MEMBERSHIP
POWER HOLDMULTI
Press to move right
MASTER
04 / 05
POWER HOLD MULTI
▶ Select
payment card
IKEA
06 / 05
MEMBERSHIP
POWER HOLD MULTI
WALMART
05 / 05
MEMBERSHIP
POWER HOLD MULTI
IKEA
06 / 05
MEMBERSHIP
POWERHOLD MULTI
▶ Select
Membership card
VISA
03 / 05
POWER HOLDMULTI
05 / 05
WALMART
POWER HOLD MULTI
9981 2034 5555 6781
Press to move right
Press to move left
Specific card data automatically appears after 3 sec.
MASTER
9833 9300 0394 1123
0321/C231 James K.
04 / 05
POWER HOLD MULTI
Specific card data automatically appears after 3 sec.
06 / 05
IKEA
POWER HOLD MULTI
1987 1008 2015 1007
Specific card data automatically appears after 3 sec.
Specific card data automatically appears after 3 sec.
Press to move left
VISA
03 / 05
POWER HOLD MULTI
03 / 05
POWER HOLD MULTI
VISA
9121 5450 2341 4423
0920/C233 James K.
MASTER
04 / 05
POWERHOLD MULTI
WALMART
05 / 05
MEMBERSHIP
POWERHOLD MULTI
VISA
03 / 05
POWER HOLD MULTI
VISA
IKEA
POWER HOLD MULTI
1987 1008 2015 1007
VISA
IKEA
POWER HOLD MULTI
1987 1008 2015 1007
▶
Multi Display
Hold for 3 sec
to enter / exit multi display mode
Press to toggle between
payment cards / membership cards
Press to move left
and to move right
*Magnetic stripe holds payment card data, while E-paper displays membership barcode.
VISA
IKEA
POWER HOLD MULTI
1987 1008 2015 1007
VISA
IKEA
POWER HOLD MULTI
1987 1008 2015 1007
VISA
WALMART
POWER HOLD MULTI
2337 5508 7715 1902
▶ Hold mode
▶ Magnetic wave
Hold for 3 sec to enter
Hold mode (Hold current
payment card on display for 10min)
Hold for 3 sec to
activate Magnetic wave mode
(Used when the card is completely
inserted into a machine)
★ E.g ATM / Gas Station
★ It may have more power consumption
★ E.g when handing over to a restaurant server
▶ Information
Hold for 3 sec to
access card information
Press to navigate
through card information
Serial number automatically appears after 3 sec.
★ Version status ★ Security status
INFORMATION
BLE ON
POWER HOLD MULTI POWER HOLD MULTI
0001E3
INFORMATION
BPAY
POWER HOLD MULTI
INFORMATION
Passcode : ON
Link to Phone : OFF
Location : OFF
POWER HOLD MULTI
0001E3
INFORMATION
BPAY
POWER HOLD MULTI
INFORMATION
MCU Ver. 1031
BLE Ver. 0.5
Hardware Ver. 1.5
CHASE
03 / 15
POWER HOLD MULTI
03 / 05
POWER HOLD MULTI
VISA
CHASE
03 / 05
POWER HOLD MULTI
CHASE
Magnetic
wave
CHASE
03 / 05
POWER HOLD MULTI
CHASE
03 / 05
POWER HOLD MULTI
• Corporate Name : BrilliantTS Co.,Ltd.
• Item title (Model name-Device) : Low power radio equipment and associated ancillary
equipment for wireless data communication systems, BPAY-CAG-01 / BPAY-CMG-01
• Item title (Model name-Device) : eCHARGER, BPAY-BTC-02
• Rechargerable Li-on : 1ICP3/13/43
• Manufacturer / Country of Orgin : BrilliantTS Co.,Ltd. / Korea
• Manufacturing date :
• Safety Number :
MSIP-CRM-BR6-BPAY-CAG-01
FCC : 2AK3I-BPAY-CAG-01
3.8V / 13mAh , Lithium-Polymer, Rechargeable
eCARD size
eCHARGER size
Reader size
85.5mm x 54mm x 0.8mm / 6g
73mm x 35mm x 0.75mm / 16g
47mm x 30mm x 11mm / 7g
3.36in. x 2.13in. x 0.2 oz / 0.01lb
2.87in. x 1.38in. x 0.56 oz / 0.04lb
1.85in. x 1.18in. x 0.25 oz / 0.02lb
1.1 inch E-paper display
About 1 and half hour
Input DC 5.0V / Output DC 4.35V / 12mA / 40mAh
14°F ~ 122°F / -10°C ~ 50°C
The usage time of the card may vary depending on the safety mode
you choose (Refer to the App or Homepage)
Card battery
Size / Weight
Standby time
Charging time
eCHARGER rated voltage / Current
Operating temperature
Display
MSIP-CRM-BR6-BPAY-CAG-01
FCC : 2AK3I-BPAY-CMG-01
BPAY-CAG-01 BPAY-CMG-01
* This device complies with part 15 of the FCC Rules.