Gaggenau CI 292 610 User manual

Gaggenau
Installation instructions..........................2
Notice de montage ...............................12
Instrucciones de instalación................22
CI 292 600
CI 292 610
CI 282 610
Induction cooktop
Table de cuisson à induction
Placa de inducción

2
Table of Contents Installationinst r uct i ons
Safety Definitions 2
IMPORTANT SAFETY INSTRUCTIONS 3
Safety Codes and Standards 3
Electric Safety 3
Related Equipment Safety 4
State of California Proposition 65 Warnings 4
Before you begin 5
Tools and parts needed 5
Parts included 5
Cabinet Requirements 5
Countertop Requirements 5
Prepare Installation Space 6
Cutout dimensions for 30" cooktops 6
Cutout dimensions for 36" cooktops 6
Ventilation 7
Installation Procedure 8
Installing the heat shield 8
Sealing tape for flush installation 9
Secure the cooktop to countertop 9
Electrical Installation 10
Electrical requirements 10
Connect Electrical Supply 10
Check the Installation 11
Customer service 11
Safety Definitions
9WARNING
This indicates that death or serious injuries may
occur as a result of non-observance of this
warning.
9CAUTION
This indicates that minor or moderate injuries may
occur as a result of non-observance of this
warning.
NOTICE: This indicates that damage to the appliance
or property may occur as a result of non-compliance
with this advisory.
Note: This alerts you to important information and/or
tips.

3
9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAF ET Y INSTRUCTIONS READ AND SAVE THESE INSTRUCTI ONS
IMPORTANT: The appliance must be installed by a
qualified installer.
INSTALLER: please leave these instructions with this
unit for the owner. Show the owner the location of the
circuit breaker or fuse. Mark it for easy reference.
OWNER: Please retain these instructions for future
reference.
WARNING
If the information in this manual is not followed exactly,
fire or shock may result causing property damage or
personal injury.
WARNING
Do not repair, replace or remove any part of the
appliance unless specifically recommended in the
manuals. Improper installation, service or maintenance
can cause injury or property damage. Refer to this
manual for guidance. All other servicing should be done
by an authorized servicer.
Remove all tape and packaging before using the
appliance. Destroy the packaging after unpacking the
appliance. Never allow children to play with packaging
material.
Hidden surfaces may have sharp edges. Use caution
when reaching behind or under appliance.
This appliance is intended for use up to a maximum
height of 13,100 feet (4,000 meters) above sea level.
Improper installation is not covered by the warranty.
WARNING
Wearers of electronic implants
The appliance may contain permanent magnets which
may affect electronic implants, e.g. heart pacemakers or
insulin pumps. Therefore, during installation, wearers of
electronic implants must maintain a minimum distance
of 4 inch (10 cm) from the appliance.
Safety Codes and Standards
This appliance complies with one or more of the
following Standards:
▯UL 858, The Standard for the Safety of Household
Electric Ranges
▯UL 507, The Standard for the Safety of Electric Fans
▯CAN/CSA-C22.2 No. 113-M1984 Fans and
Ventilators
▯CAN/CSA-C22.2 No. 61-M89 Household Cooking
Ranges
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
Electric Safety
WARNING
Before you plug in an electrical cord or turn on power
supply, make sure all controls are in the OFF position.
If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
The circuit breaker should have a contact separation of
at least 3 mm on all poles.
Be sure your appliance is properly installed and
grounded by a qualified technician. Installation,
electrical connections and grounding must comply with
all applicable codes.
Before installing, turn power OFF at the service panel.
Lock service panel to prevent power from being turned
ON accidentally.
WARNING
IMPROPER GROUNDING CAN RESULT IN A RISK OF
ELECTRIC SHOCK
Consult a qualified electrician if the grounding
instructions are not completely understood, or if
doubt exists as to whether the appliance is
properly grounded. DO NOT USE AN EXTENSION
CORD.

9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
4
Related Equipment Safety
The appliance should only be used if installed by a
qualified technician in accordance with these
installation instructions. The manufacturer is not
responsible for any damage resulting from incorrect
installation.
Never modify or alter the construction of the appliance.
For example, do not remove leveling legs, panels, wire
covers or anti-tip brackets/screws.
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located
above the surface units should be avoided. If cabinet
storage is to be provided, the risk can be reduced by
installing a hood that projects horizontally a minimum of
5 inches (127 mm) beyond the bottom of the cabinet.
Verify that cabinets above the cooktop are a maximum of
13" (330 mm) deep.
DO NOT install refrigerators, dishwashers, ovens
(without ventilation), or washing machines below the
Cooktop.
Note: We strongly recommend the installation of a
ventilation system with this appliance.
State of California Proposition 65
Warnings
WARNING
This product can expose you to chemicals including
vinyl chloride, which is known to the State of California
to cause cancer and birth defects or other reproductive
harm. For more information go to
www.P65Warnings.ca.gov.

5
Before you begin
Tools and parts needed
▯Phillips Head Screwdriver
▯Pencil
▯Drill with ¼" (6 mm) bit
▯Jigsaw
▯Tape Measure
Note: Additional materials may be necessary for
installation in solid surface countertops. Contact the
countertop manufacturer.
Parts included
Cabinet Requirements
The distance from the top of the cooktop to the bottom
of cabinets above must be a minimum of A=30"
(762 mm) min. This distance can be reduced to A=24"
(610 mm) when the bottom of the wood or metal cabinet
is protected by not less than ¼" (6.35 mm)
flame-retardant millboard covered with not less than
no. 28 gauge sheet metal, 0.015" (0.4 mm) stainless
steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm)
copper.
Verify that the cabinets above the cooktop are a
maximum of B=13" (330 mm) deep.
Countertop Requirements
9WARNING
To reduce the risk of ignition of surrounding
combustible materials, install at least 2" (51 mm)
from both sidewalls and the rear wall.
The countertop must be level and horizontal. The
stability of the countertop must be maintained after the
cut-out has been made.
Solid surface countertops often require special
installations. For example, heat-reflective tape and
rounded corners may be necessary. Contact the
countertop manufacturer for instructions specific to
your countertop.
%
$

6
Prepare Installation Space
Create the cut-out in the countertop according to the
installation diagram. The angle of the cut surface to the
countertop must be 90°.
The lateral cut-out edges must be flat in order to ensure
that the retaining springs are positioned properly on the
appliance. With multi-layered countertops, secure strips
laterally in the cut-out if necessary.
After creating cut-out, remove shavings. Seal cut
surfaces in a heat- and water-resistant manner.
Observe minimum distance between device underside
and cabinet surfaces of 3/8" (10 mm).
The worktop into which the cooktop is installed must be
heat-resistant up to 140° F (90 °C).
The worktop must be reinforced if it is less than 4/5inch
(20 mm) thick.
If the thickness of the worktop into which the cooktop is
installed does not comply with the specifications,
reinforce the worktop using a fire- and water-resistant
material until it reaches the minimum thickness.
Otherwise, sufficient stability cannot be assured.
▯The worktop into which the cooktop is installed
should withstand loads of approx. 133 lbs (60 kg).
▯Only check the evenness of the cooktop after it has
been installed.
For flush installation in tiled countertops:
Note: If necessary, raise the support surfaces using
heat and water resistant strips.
Cutout dimensions for 30" cooktops
Model: CI 282 610
Cutout dimensions for 36" cooktops
Model: CI 292 610





[
¡



PLQ 




 PP
PLQ 
PLQ




  


[
¡

PLQ 
  





 PP
PLQ 
PLQ




  


7
Model: CI 292 600 Ventilation
To assure that the appliance works correctly, the
cooktop MUST be sufficiently ventilated.
Since the ventilation in the lower section of the
appliance requires a sufficient supply of fresh air, the
cabinet must be designed accordingly. The following is
required for this:
▯A minimum clearance between the rear of the
cupboard and the kitchen wall, and between the
surface of the worktop and the upper area of the
drawer.
▯An opening at the top to the rear of the cupboard.
▯If the minimum clearance of 25/32 inch (20 mm) is not
provided at the rear of the cupboard, you must
create an opening on the underside.
PLQ 
  
PLQ   



    


  
 PP
PD[5




5






[
¡

PLQæʌ¼ʕʔ
PLQ
 PP
PLQë
PLQèè¼ʓʘ
 PP
PLQæʌ¼ʕʔ
 PP

8
▯If the inside of the cupboard is no wider than
29 1/2inch (750 mm), make cutouts in the side
panels.
Note: If the appliance is installed in an island unit or
another installation that is not described here, you must
ensure that the cooktop is sufficiently ventilated.
Installation Procedure
9CAUTION
Sharp edges. Use protective gloves when
installing the cooktop.
Note: The appliance is heavy. It is advisable to install it
with a second person.
Installing the heat shield
9CAUTION
Sharp edges. Use protective gloves when
installing the plate.
For safety reasons, the heat shield must be properly
installed when closed cabinets are used. This prevents
components from overheating as a result of the
recirculation of hot air from the cooktop.
The heat shield is the same width as the cooktop. For
shipping, it is screwed to the burner box.
After unpacking the cooktop, unscrew the heat shield.
The heat shield will be able to rotate freely, as shown in
the illustration.
$ê
PLQ
 PP


9
Sealing tape for flush installation
Attach the adhesive sealing tape around the edges of
the countertop.
Note: Do not apply the sealing tape to the cooktop.
Secure the cooktop to countertop
9CAUTION
Do not let the glass drop into place. Make sure
that it is supported along a broad area of the
edges when carefully placing the cooktop into the
cutout.
The appliance must be secured from below using the
hold down brackets provided so it does not slip.
1Rotate the appliance and fit it so that the screws
provided are seated loosely in the holes. Move the
hold down brackets so that the appliance can be
placed in the cutout.
2Place the appliance carefully into the cutout.
3Insert the clamping screws into the hold down
brackets and fix the appliance to the countertop.
Tighten screws.
Note: Protect delicate countertops by placing a
wooden disk underneath.

10
Electrical Installation
Electrical requirements
You can find the identification plate with the electrical
specifications on the underside of the appliance. The
junction box must be located within 3 feet of the
cooktop connection. It should be easily accessible for
service purposes.
Power supply
Connect Electrical Supply
9CAUTION
Before installing, turn off at the service panel.
Lock service panel to prevent power from being
turned on accidentally.
9CAUTION
To reduce the risk of electric shock and fire, do
not use a flexible power supply cord.
Refer to data plate for more information. See "Service"
for data plate location.
The branch-circuit breakers ampacity, the wire sizes and
the connections must conform to the requirements of
the National Electrical Code or Canadian Electrical
Code and all local codes and ordinances.
Attach flexible conduit to the junction box. Connect the
lead wires to the junction box supply wires in proper
phase:
▯black (L1) to black
▯red (L2) to red
▯green or bare to ground
If the cooktop is installed and connected as specified
above, it will be completely grounded in compliance with
the National Electrical Code.
DSSUR[PP
&RQQHFWLRQ
Å-´%R[
PD[PP)LWWLQJ&RQGXLWPP
&RQGXLWDSSUR[IWaPP
PLQPP
DLUFOHDUDQFH
&,&,PRGHOV
$PSFLUFXLWEUHDNHU
9ROWV:LUH+]
9ROWV:LUH+]
$OOZLWKPIOH[LEOHFRQGXLWLQFOXGHG
&,PRGHOV
$PSFLUFXLWEUHDNHU
9ROWV:LUH+]
9ROWV:LUH+]
$OOZLWKPIOH[LEOHFRQGXLWLQFOXGHG
1 House power supply cord
2 Black wire
3 Junction box
4 Cooktop power supply cord
5 Grounded green or bare cable
6 Certified UL connector
7 Red wire





