Gaggenau AH 600-190 Product guide

Operating and assembly instructions
AH 600-190
Extractor hood
00
1
2
3

AH 600-190
1
Preface
1. Important notes Page 3-4
1.1 For your safety Page 3
1.2 Operating for the first time Page 4
1.3 About use Page 4
2. Structure and operating principle Page -6
2.1 Structure of the appliance Page
2.2 Accessories/special accessories Page
2.3 Operating principle Page 6
3. Operation Page 7-8
3.1 Switching on and off Page 7
3.2 Special functions Page 8
4. Cleaning and care Page 9-10
5. Maintenance Page 11
6. Assem ly instructions Page12-17
6.1 Technical data Page 12
6.2 Installation Page 12-17

2
Preface
With your new extractor hood, working in the
kitchen will e even more fun.
The appliance offers you a number of
advantages:
– effective extraction thanks to the so-called
“Coanda effect”
– low operating noise
To ensure that you will be able to use this appli-
ance in all its diversity, read through the operating
and assembly instructions conscientiously efore
operating it for the first time. The instructions
contain important notes on use, installation and
maintenance of the appliance.
On the following page you will find important
notes on safety and operation. These will serve
to ensure your personal safety and the lasting
value of your appliance.
You will find notes on Page 4 that you ought to
observe efore operating the appliance for
the first time.
The chapters entitled “Structure and operating
principle” and “Operation” will tell you all the
things your extractor hood is capable of doing
and how the appliance is operated.
Tips and hints in the chapter entitled “Cleaning
and care” will make sure that your appliance will
stay operable and beautiful for a long time.
And now we wish you lots of fun with your
new extractor hood.
0
2
3
1
0
Fig. 1

3
1. Important notes
1.1 For your safety
–Damaged appliances must not be operated.
– The appliance must only be connected by an
authorised specialist, paying attention to
the relevant regulations of the power supply
companies and the regional construction
regulations.
Also o serve the assem ly instructions!
–Connecting ca les must not come into contact
with hot cooking surfaces.
–Do not operate the extractor hood without
inserted lamps.
– Never operate the appliance without a grease
filter.
–Hazardous or explosive substances and
vapours must not be extracted!
–The user is responsible for expert use and the
perfect condition of the appliance.
– Only ever operate the appliance under super-
vision.
–Caution! Over-greased filters are a fire risk!
Only ever deep-fry under the extractor under
constant supervision. Pay attention to cleaning
the grease filter on a regular basis.
–Fire risk! Do not flambé meals under the
extractor hood!
– Operation of the extractor hood a ove a hearth
for solid fuels (coal or wood etc.) is only partly
permitted.
–Gas appliances may only be used under the
extractor hood when pots and pans are placed
on them!
– When using more than 3 gas-operated rings
at the same time, please operate the extractor
hood at level 2 or higher. This prevents a build-
up of heat in the appliance.
–Do not place any heavy objects on the appli-
ance; this will have a detrimental effect on
functioning.
–Do not clean the appliance with a steam
cleaning apparatus or with water pressure
because this poses a risk of short-circuits.
– Isolate the appliance from the mains during
every maintenance operation. To do this,
remove the mains plug or actuate the correspon-
ding fuse.
If the mains plug is not accessible, the appliance
must be deenergised by means of the domestic
installation fuse.
–Repairs must be carried out by authorised
specialists, thus ensuring electrical safety.
–No warranty claims can be lodged in the
event of damage caused by failure to observe
these instructions.
– Adequate incoming air must be ensured if a
wood, coal, gas or oil heater or an open hearth is
operated in the same room as the one in which
the hood is installed.
– Safe operation is possible whenever the partial
vacuum in the place where the firing equip-
ment is installed does not exceed 4 Pa
(0.04 mbar). This can be achieved whenever
the air needed for combustion is able to enter
through openings that cannot be sealed, for
example in doors, windows, incoming/exhaust
air wall boxes or other technical means.
– If the appliance is to be operated only with the
window open (to ensure adequate incoming
air), you can use the window switch.
A switch (normally open) is fitted on the window.
On the appliance, this switch is connected to the
window switch terminal on the main electronics.
The appliance can now only be operated when
the window is open.
Important: the window switch must only be
connected by an authorised specialist.
Note: The light function works without restriction.
–After a power failure, the extactor will not go
on again automatically. You can recommence
operation by turning a knob or by pressing any
key.
Technical modifications reserved.

1.2 Operating for the first time
Before operating the appliance for the first time,
please pay attention to the following notes:
–The appliance must be installed and connected
by a specialist before it is operated for the first
time.
–The rating plate for this appliance is included
with the instructions on a separate sheet. Store
the rating plate in the same location as your
operating and assembly instructions. You need
the rating plate for possible damage and
warranty cases.
–Conscientiously read through the operating
and assembly instructions before operating the
appliance for the first time.
–Remove the packaging from the appliance and
dispose of it properly. Pay attention to the fact
that there are accessories in the packaging.
Keep packaging elements out of the reach of
children!
–Thoroughly clean the appliance before using it
for the first time. (see chapter entitled “Cleaning
and care”).
–Before operating the appliance for the first
time, check that the mains connection is in
proper working order.
1.3 A out use
–The appliance is intended solely for use in the
household and must not be put to any other uses.
–In the event of malfunctions, first of all check
the household fuses. If the problem has nothing
to do with the power supply, please contact your
specialist dealer or your local Gaggenau after-
sales service.
4

2. Structure and operating principle
2.1 Structure of the appliance
2.2 Accessories/special accessories
You can order the following special accessories:
– Activated charcoal filter: KF 600-090
– Back draught flap RK 040-150: Back draught
flap for insertion in the extractor’s blow-out
opening
– Flexible aluminium pipe AR 040-150:
DN 1 0 up to 3. m
Length with 2 hose clamps:
1Display
2Glass plates
3Air duct
4Control panel
5Grease filter key
6Ventilation level display
7“Coanda level” key
8“Light” control knob
9“Ventilation level” control knob
10 “After-running” key
11 “After-running” symbol
12 “Grease filter saturation” symbol
13 “Coanda level” symbol
14 “Intensive level” symbol
15 “Intensive level” key
Installation accessories:
Exhaust air:
Ventilation duct for ceiling heights of 2.27 - 2.60 m:
LK 600-010
Ventilation duct for ceiling heights of 2.61 - 3.00 m:
LK 600-020
Air recirculation:
Ventilation duct for ceiling heights of 2.39 - 2.60 m:
LK 600-110
Ventilation duct for ceiling heights of 2.61 - 3.00 m:
LK 600-120
00
1
2
3
Fig. 2
00
1
2
3
Fig. 3
567 8 9
10 11 12 13 14 15
3
2
4
2
1

2.3 Operating principle
This extractor hood swiftly and silently extracts
all odours produced while cooking. You can set
different intensity levels depending on the intensity
of odours.
The exhaust air first passes through the integrated
grease filter. The grease filter intercepts and traps
the grease and odour particles in the air.
In the exhaust air mode:
The fan in the extractor hood sucks in the kitchen
vapours and passes them through the grease filter
to outdoors. The grease filter absorbs the greasy
components in the kitchen vapours (see Fig. 4).
In the air recirculation mode:
An activated charcoal filter (special accessory)
must be installed. The fan in the extractor hood
sucks in kitchen vapours and returns them to
the kitchen after purification in the grease and
activated charcoal filter. The grease filter absorbs
the greasy components in the kitchen vapours.
The activated charcoal filter binds odour particles
(see Fig. ).
The “Coanda effect”
Kitchen vapours are extracted even better with the
“Coanda effect”. By means of an additional motor,
kitchen vapours are passed swiftly and effectively
into the hood’s extraction zone. An additional fan
on the front edge of the kitchen extractor hood
generates an air stream that is diverted around a
cylinder towards the rear. This ensures that kitchen
vapours are routed completely into the extractor
hood’s filter area (see Fig. 6).
6
Fig. 4
Fig.
Fig. 6

3.1 Switching on and off
Switching on
– Turn the “Ventilation level” control knob to the
ventilation level you require (Fig. 7).
– The set level is displayed.
Switching off
– Turn the “Ventilation level” control knob to
the 0 position (Fig. 8).
– The set level 0 is displayed for a few seconds.
Note:
The light can be switched on and off at any time.
To do this, turn the “Light” control knob to the
(Light) position.
Switching on the Coanda level
– Turn the “Ventilation level” control knob to the
level you require.
– Press the Coanda level key.
– The level you have set and the Coanda level
symbol appear on the display (Fig. 9).
Note: You can change to any ventilation level, and
the Coanda level remains set.
Switching off the Coanda level:
– Press the “Coanda level” key or turn the
“Ventilation level” knob to the 0 position.
3. Operation
7
00
1
2
3
Fig. 7
00
1
2
Fig. 8
Fig. 9
00
1
2
3

8
3.2 Special functions
Intensive level
You should select the intensive level when
browning and frying in an open pan.
Switching on: (Fig. 10)
– Turn the control knob to a ventilation level (1-3).
– Press the intensive level key. The intensive level
symbol appears on the display. The previously
selected ventilation level flashes on the display.
After a few minutes, the appliance switches
back automatically to the previously selected
ventilation level.
or
– Press the intensive level key. The intensive level
symbol appears on the display. The appliance
is now operated at the intensive level for a few
minutes and then switches off automatically.
Ending the intensive level prematurely:
– Turn the “Ventilation level” knob to the 0 position
or
– turn the “Ventilation level” knob to any level or
– press the intensive level key once again.
After-running
Switching on:
– Press the (After-running) key.
– The (After-running) symbol and ventilation
level 2 light up on the display (Fig. 11).
or
– Turn the “Ventilation level” control knob to any
level.
– Press the (After-running) key.
– The (After-running) symbol and the set
ventilation level light up on the display (Fig. 12).
– The extractor hood continues running for
10 minutes.
Switching off:
– Turn the “Ventilation level” control knob to the 0
position.
or
– Press the (After-running) key.
00
1
2
3
Fig. 10
Fig. 11
Fig. 12
00
1
2
3

Cleaning the grease filters:
The (Grease filter saturation) symbol flashes
on the display after an operating time of 30 hours.
Flashing of this symbol signals to you that the
grease filters have to be cleaned. The grease filters
can be cleaned at any time, even if the (Grease
filter saturation) symbol does not flash. The metal
filters can be removed easily for cleaning.
Proceed as follows:
– Grip the grease filter handles and press the
slide towards the rear.
– Pull the grease filter out of its mount in the
downward direction (Fig. 13).
– Repeat the operation with the other grease
filters.
You can clean the metal grease filters in a
dishwasher at a maximum temperature of 6 °C.
Place the grease filters vertically in the dishwasher
to ensure that no food remainders will stay on them.
Slight discoloration can occur when cleaning the
grease filters in a dishwasher.
When replacing the grease filters, wipe out
the inner part of the housing with hot detergent
solution.
Reinsert the grease filters in the hood after
cleaning. Install them in the reverse order to
removal.
Press the (Grease filter) key to set the elapsed
hours counter to zero; the (Grease filter) symbol
stops flashing.
Do not clean the appliance with a steam cleaning
apparatus or with water pressure because this
poses a risk of short-circuits.
9
4. Cleaning and care
Note:
The handles of the grease filters must be visible
after installation. They can no longer be removed
if the handles are in the inner part of the housing.
Fig. 13

Air recirculation
If, when purchasing the extractor hood, you have
decided in favour of the air recirculation mode,
the activated charcoal filter KF 600-090 must be
replaced after a certain amount of hood operation.
Note: The activated charcoal filter is not included
in the scope of delivery of the hood.
Activated charcoal filters do not contain any
polluting substances. Old activated charcoal filters
can be disposed of as domestic waste. If used once
daily, the activated charcoal filter must be replaced
approximately once to twice every year. First
remove the grease filter. Press out the two tabs in
the downward direction and remove the activated
charcoal filter from the hood in the downward
direction (see Fig. 14). Replace the old activated
charcoal filter by the new one. Install in the reverse
order.
Cleaning the extractor hood
Clean the stainless steel parts of the extractor
hood with mild rinsing detergent and apply
stainless steel care agent to the metal surfaces
using a soft cloth.
Clean the two glass plates in a dishwasher.
Do not use any strong or caustic cleaning agents or
brushes and abrasive cleaner.
Do not use any abrasive sponges either. Use
commercially available window cleaner and apply
it to a soft, moist cloth.
Only clean the switch panel with a soft cloth. Do
not use any cleaning agent as it might be agressive
to the inscription markings.
10
Fig. 14

11
First disconnect the appliance from the mains
efore carrying out any repairs.
In the event of malfunctions, first of all check
the household fuses.
If the power supply is in proper working order,
but the appliance is nevertheless not functioning,
then please contact your specialist dealer or your
responsible Gaggenau after-sales service.
Specify the appliance type (see rating plate).
Repairs must only be carried out by authorised
specialists, thus ensuring the safety of the
appliance. Improper tampering will render all
warranty claims null and void.
Lamp replacement
Caution: Disconnect the power supply before
replacing lamps!
Caution: Lamps may still be hot shortly after use!
Risk of burns.
– Remove the grease filters.
– Remove the screws on the lamp cover. The lamp
cover tilts down and cannot be removed from
the appliance (Fig. 1 ).
– Turn the lamp to the left and remove the lamp
(Fig. 16).
Defective lamps must only be replaced by lamps
of the same type (Cool Beam)! You can obtain
the original spare part (No. 03602611) from trade
dealers or via Gaggenau after-sales service.
Inserting the lamp
– Insert the lamp and turn it to the right.
– Screw down the lamp cover again.
– Connect the appliance to the mains again.
. Maintenance
Fig. 16
Fig. 1

12
6.1 Technical data
Weight: 28 kg
Dimensions: 898 x 20 mm
Electrical connection
Pay attention to the rating plate data.
The mains connecting cable must at least
correspond to the type H 0 VV-F G 0,7 .
When replacing the mains cable, you must
dismantle the tubular connection piece (undo
2 screws).
The appliance must only be connected by an
authorised specialist. The specialist is respon-
sible for perfect functioning of the appliance at its
installation location. He must explain the operating
principle of the appliance to the user with refe-
rence to the operating instructions. He must explain
to the user how the appliance can be isolated from
the mains whenever required.
Connection possi ilities
The extractor hood was conceived for the exhaust
air or air recirculation mode. The exhaust air can be
routed into a separate exhaust air shaft or directly
into the open through the outside wall.
The connector of the connecting cable is connec-
ted to the socket that is located behind the duct
cover on the wall. If this is not possible, it must be
possible to isolate all poles of the appliance from
the mains by way of the domestic fuse, or by means
of accessible isolating device with a contact gap
of at least 3 mm.
6.2 Installation
The applicable regulations of the energy supply
companies and the regional construction
regulations must be observed when installing
the hood.
The minimum distance from the worktop to the
bottom edge of the wall hood is for electrical
appliances 600 mm and for gas appliances 670 mm.
The wall hood was conceived for the exhaust air
or air recirculation mode. The exhaust air can be
routed into a separate exhaust air shaft or directly
into the open through the outside wall.
It is not allowed to pass the exhaust air into a flue
or exhaust air chimney that is in operation or into a
shaft that is linked to the heating basement. Consult
the chimney sweep responsible for your district
whenever you wish to pass the exhaust air into a
chimney that is not in operation.
During the course of planning, a chimney sweep
must be consulted if a room air-dependent hearth
is operated in the same room as the one in which a
hood is operated in the exhaust air mode. Adequate
incoming air must be ensured. The applicable
construction and safety regulations must be
observed.
Adequate incoming air must be ensured if a wood,
coal, gas or oil heater or an open hearth is operated
in the same room as the one in which the hood is
installed.
Safe operation is possible whenever the partial
vacuum in the place where the firing equipment
is installed does not exceed 4 Pa (0.04 mbar).
This can be achieved whenever the air needed for
combustion is able to enter through openings that
cannot be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or other technical
means.
6. Assembly instructions
AH 600-190 FD xxxx xxxx
AC 220-240V 0Hz 34 W xxxx
160W 3 W 3x 0W

Flexible aluminium pipes, corrosion-protected
sheet metal pipes and exhaust air pipes whose
material conforms to fire B1 in accordance with
DIN 4102 can be used. Exhaust air pipes should
have a nominal diameter of 1 0 mm.
Pay particular attention to ensuring that
– the exhaust air ducts and pipes are kept as short
as possible
– the pipes are not laid at an acute angle, but as
bends and that they are inserted into the shaft at
an inclined upward angle and
– there are no cross-sectional constrictions in the
upward direction (this reduces the volume flow).
As standard, the blow-out opening of the wall hood
is in the upward direction.
To pass exhaust air through the outer wall, we
recommend the use of our telescopic wall box
TM 1 0-04 (Ø 1 0).
Note:
To prevent the ingress of water, e.g. condensate or
rain water from an uncovered exhaust air shaft, our
condensate separator RV 060-1 0 must be installed
in the exhaust air line. The condensate separator
must still be acciessible after installation.
Air recirculation
You need the following accessories to install the
air recirculation hood:
–KF 600-090: activated charcoal filter:
Depending on the ceiling height, the following duct
units are at your disposal for air recirculation:
–LK 600-110: Ventilation duct for a ceiling height
of 2.39 - 2.60 m
–LK 600-120: Ventilation duct for a ceiling height
of 2.61 - 3.00 m
The dimensions above refer to a distance of 1.60 m
from the floor to the bottom edge of the hood.
Exhaust air operation
Depending on the ceiling height, the following duct
units are at your disposal for exhaust air operation:
–LK 600-010: Ventilation duct for a ceiling height
of 2.27 to 2.60 m
–LK 600-020: Ventilation duct for a ceiling height
of 2.61 - 3.00 m
The dimensions above refer to a distance of 1.60 m
from the floor to the bottom edge of the hood.
If required, a side outlet for the air duct is available
at an extra charge.
The socket must be place behind the duct cover on
the wall.
13
520
260
150 480
1600
522.5
min. 600
over electric cooker
min. 670
over gas cooker Exhaust air:
750 - 1400
Air recirculation:
825 - 1400
ood height
Exhaust air: 2.35 - 3.0
Air recirculation: 2.43 - 3.0
Ceiling height
Sus-
pension
Fig. 17

Proceed as follows:
Exhaust air operation:
– From the bottom edge of the hood, mark a center
line on the wall.
– With the aid of the drilling template, mark the
positions of the screws on the wall. Mark the
contour of the hook-in area. This will make it
easier to hook in the hood (Fig. 18).
– Pay attention to the minimum clearance of 600 mm
for electric cookers and 670 mm for gas cookers.
The bottom edge of the template corresponds to
the bottom from edge of the hood.
– Using the drilling template, drill the 6 holes for
the hood (area I of the drilling template) and the
two holes for suspending the chimney (area II of
the drilling template). In the top two securing
holes for the hood, fix the two hooks ewith the
countersunk screws d. Make sure that the hooks
lie flatly on the wall. In certain circumstances you
may have to countersink the drill holes. Fit the
included dowels ain the other drill holes.
Note: Pay attention to any special accessories that
you may have to fit.
– Screw on the retaining bracket for the chimney
paneling.
– Detach the grease filters.
– Unscrew the two black plates on the left and right
of the chimney.
– Hang the hood on the two hooks. Adjust the
suspended element with the recessed head
screw and align the hood using a spirit level
(Fig. 19).
14
448
137
625
270
300
15
310
mind. 600 Elektro
mind. 670 Gas
230
Fig. 18
Fig. 19
min. 600 electric
min. 670 gas
Important: Before marking the securing holes,
make sure that no electricity or water lines or
other lines are laid at the drilling points in the wall.

– Secure the hood to the wall using the 4 screws
with shims c(Fig. 20).
– Establish the pipe connection.
– Establish the electrical connection.
– Extract the protective file from the chimney
paneling.
Note: Avoid damaging the sensitive stainless steel
surfaces.
– Join the chimney shoe with the chimney base
using the 6 screws (3. x 9. mm) (Fig. 21).
– Fit the top of the chimney into the base. Make
sure that the fastening holes on the side are at the
top.
– Secure the top duct unit with 2 screws on the
ceiling holder.
– Pull the shoe down into its final position
(Fig. 22).
Note: Avoid scratches when fitting the elements
into one another by placing the assembly template,
for example, over the edge of the bottom chimney
paneling to protect it.
– Reinsert the grease filters.
– Again screw in the two black plates on the left
and right of the chimney.
– Place the glass plates on the black plates.
1
Fig. 20
Fig. 21
Fig. 22

Recirculation air operation
– From the bottom edge of the hood, mark a center
line on the wall.
– With the aid of the drilling template, mark the
positions of the screws on the wall. Mark the
contour of the hook-in area. This will make it
easier to hook in the hood (Fig. 23).
– Pay attention to the minimum clearance of 600 mm
for electric cookers and 670 mm for gas cookers.
The bottom edge of the template corresponds to
the bottom from edge of the hood.
– Using the drilling template, drill the 6 holes for the
hood (area I of the drilling template) and the two
holes for suspending the chimney (area II of the
drilling template). In the top two securing holes for
the hood, fix the two hooks ewith the countersunk
screws d. Make sure that the hooks lie flatly on the
wall. In certain circumstances you may have to
countersink the drill holes. Fit the included dowels
ain the other drill holes.
Note: Pay attention to any special accessories that
you may have to fit.
– Detach the grease filters.
– Unscrew the two black plates on the left and right
of the chimney.
– Hang the hood on the two hooks. Adjust the
suspended element with the recessed head screw
and align the hood using a spirit level (Figure 19).
– Secure the hood to the wall using the 4 screws
with shims c.
– Screw the retaining bracket for the chimney
paneling onto the wall together with the two
retaining brackets for the housing (air guidance)
(Fig. 24).
16
448
137
625
270
300
15
310
mind. 600 Elektro
mind. 670 Gas
230
Fig. 23
Fig. 24
min. 600 electric
min. 670 gas

– Screw together the air guidance housing and
screw it onto the two retaining brackets (Fig. 2 ).
– Establish the pipe connection between the air
connection piece and the air guidance housing.
– Establish the electrical connection.
– Stick the included sealing strips (8 strips) around
the air slots on the top chimney paneling.
– Remove the protective foil from the chimney
paneling.
Note: Avoid damaging the sensitive stainless steel
surfaces.
– Join the chimney shoe with the chimney base
using the 6 screws (3. x 9. mm) (Fig. 26).
– Fit the top of the chimney into the base. Make
sure that the fastening holes on the side are at the
top.
– Secure the top duct unit with 2 screws on the
ceiling holder.
– Pull the shoe down into its final position
(Fig. 27)
Note: Avoid scratches when fitting the elements
into one another by placing the assembly template,
for example, over the edge of the bottom chimney
paneling to protect it.
– Make sure that an activated charcoal filter is
installed (see page 10).
– Reinsert the grease filters.
– Again screw in the two black plates on the left
and right of the chimney.
– Place the glass plates on the black plates.
03.6028.63 12.99 SK 17
Fig. 2
Fig. 26
Fig. 27

GAGGENAU HAUSGERÄTE GMBH
P.O. BOX 12 60 · D-76568 GAGGENAU, GERMANY
Y(0 72 25) 67-0 · FAX [phone]
Y(018 01) 11 22 11 (KUNDENDIENST) · Y(018 01) 33 53 04 (ERSATZTEILE)
www.gaggenau.com
GAGGENAU HAUSGERÄTE GMBH
P.O. BOX 10 02 50 · D-80076 MÜNCHEN
Y(0 8 ) 45 0-01
FAX (0 8 ) 45 0-23 47