Galaxy Press GS-207M User manual

1
Operation Manual
(GS-207M)
Safety Instructions
When using your heat press,
basic precautions should always be followed,
including the following:
1. Read all instructions.
2. Use heat press only for its intended use.
3. To reduce the risk of electric shock, do not immerse the heat press in water or other liquids.
4. Never pull cord to disconnect from outlet, instead grasp plug and pull to disconnect.
5. Do not allow cord to touch hot surfaces, allow heat press to cool completely before storing.
6. Do not operate heat press with a damaged cord or if the equipment has been dropped or
damaged.To reduce the risk of electric shock, do not disassemble or attempt to repair the
heat press. Take it to a qualified service person for examination and repair. Incorrect
assembly or repair could increase the risk of fire, electric shock, or injury to persons when the
equipment is used.
7. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
8. Close supervision is necessary for any heat press being used by or near children. Do not
leave equipment unattended while connected.
9. Burns can occur when touching hot metal parts.
10. To reduce the likelihood of circuit overload, do not operate other high voltage equipment on
the same circuit.
11. If an extension cord is necessary, then a 20 amperage rated cord should be used. Cords
rated for less amperage may overheat. Care should be taken to arrange the cord so that it
cannot be pulled or tripped over.

2
Table Of Contents
Safety Instructions………………………..1
Technical Parameters……………………
Machine View……………………………..
Control Panel Guide……………………...
Operating Instructions……………………
⚫Connecting the System…………………………………………...……5
⚫Turning the System On…………………………………….………......6
⚫Adjusting the Temperature……………………………………….........6-7
⚫Adjusting the Time………………………………………………..….....7
⚫Printing and Pressing………………………………………………......8-9
⚫How to Change Heater…………………………………………………9
⚫Sub Menu Setting…........………………………………………...……10-11
Exploded Views And Parts List…………..12-10
Electrical Schematic……………………....20
1
1
3
1
4
1
5
1
5-11
1

3
Technical Parameters
Model:
GS-207M
Heater Size:
W195mm*H170mm
for 400ml/500ml/600ml aluminum sports water bottle.
Power(120volt)
4*300W/4*120W
16.1 Amps(max)
Power(240volt)
4*300W/4*120W
8.1Amps(max)
Temperature Range：
Max.220℃/430℉
Time Range：
0~999S
Machine Size：
65.2×33.9×28.5cm
Packing Size：
73×43×40cm
Packing Weight：
24kg
Maximum Paper
Printing Size:
400ml sports bottle: 175*99mm(L*W)
500ml sports bottle: 175*114mm(L*W)
600ml sports bottle: 175*134mm(L*W)
Suggest Temp&Time
Setting:
150C/190C 40-50secs
302F/374F 40-50secs
Certificate：
CE,FCC
Warranty:
One year for whole machine except heaters

4
Machine View

5
Control Panel Guide
Operation Instructions
1.Connecting the System
⚫CONNECT THE POWER CORD
Connect the power cord into a properly grounded electrical outlet with a sufficient amperage
rating.
⚫VOLTAGE
120 Volt –GS-207M requires a full 20 amp grounded circuit for 120 volt operation.
240 Volt –GS-207M requires a full 10 amp grounded circuit for 240 volt operation.
⚫EXTENSION CORDS If used, should be as short as possible and not less than 12
gauge.Heavy duty cords are recommended.
⚫CIRCUITS that have less than 15 amps or that have other high demand equipment or
appliances(especially more than one heat seal machine) plugged in, should not be used.

6
NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or a similarly qualified person in order to avoid hazard.
2.Turn On the System
3.Adjusting the Temperature
3.1 Press the Mode Select button located
in the center of the Control Panel
(fig.3.1).Press (+) and (-) button to
select different heater. (fig.3.2).
3.2 For heater 1/2 and 3/4, press “set”
button to choose “start temp”or
“finish temp”, press (+) and (-)button
to set temperature. For heater 5 and
6,press “set” button to choose “start
temp”, press (+) and (-)button to set
temperature.The temperature can be
set from 0° C (0° F) to 220° C (428°
F). (fig.3.2)
3.3 press set button again to finish
setting,move the cursor to “next”,
ready to enter time setting page.
(fig.3.3)
⚫Switch on the system. (fig.2.1)
3.1
3.2
3.3
2.1

7
4.Adjusting Time
4.2 Press “set”button to activate time
value setting. Press (-) button to
lower the value ,or press the (+)
button to raise the time value .The
time setting range can be set from
0~999. Move the cursor to
“back”,press “set’button to get back
to the main interface. (fig.4.2)
4.1 In the time setting page, Press (+)
and (-) button to select different
heater..(fig.4.1)
Remark:
1. heater 1/2 represent no.1 and no.2 heater, can only be set temperature at once time
together, because left air cylinder close the heater 1/2 together. Heater 1/2 can set “start
temp”and “finish temp”.
2. heater 3/4 represent no.3 and no.4 heater, can only be set temperature at once time
together, because right air cylinder close the heater 3/4 together. Heater 3/4 can set “start
temp”and “finish temp”.
3. Heater 5 does not work for GS-207M.
4. Heater 6 does not work for GS-207M
4.1
4.2

8
5.Printing And Pressing
5.3 Then close handle to start transfer
printing process.
5.1 Once heater reaches start
temperature,put bottles inside of mug heater
5.1
Remark:
1. Station 1/2 must work with two mugs inside together, working only with 1 mug inside
will damage the machine.
2. Station 3/4 must work with two mugs inside together, working only with 1 mug inside
will damage the machine.
3. Each heater’s temperature is separately controlled by different triac, can be calibrated
separately. But we do not suggest customer make calibration unless there is a need.
5.2
5.3 Once printing process is over, buzzer
will alarm and open the handle then take
out bottles out of machine.
5.4
5.2 Adjust suitable pressure by turning
pressure knob.
5.3

9
6.How to Change Heater
7.Sub Menu Introduction
Plug off the 4 phase plug
Take off the heater. Then do the
opposite operation can change a new
heater onto the machine
7.1 Language setting.we offer 4
language for customer needs.
English/Spanish/Russia/Portuguese.
(fig.7.1). Once finish setting,go to
next page.
In the time setting page, there is sub menu button, move the cursor to the button,
press “set”button to enter into sub menu
7.1

10
7.2 Temperature calibration setting.
Customer can make calibration on
each heater once the heater’s
temperature is not
correct.(fig.7.2).Once finish
setting,go to next page.
7.3 Fahrenheit and Celsius setting.
(fig.7.3).Once finish setting,go to
next page.
7.4 Auto-sleep setting. Customer can
set auto-sleep time. Once time is
reached,machine will auto close
without any operation (fig.7.4).Once
finish setting,go to next page.
7.2
7.3
7.4

11
7.5 Brightness setting.Customer can
reduce or increase brightness of the
screen. (fig.7.5).Once finish
setting,go to next page.
7.6 Counter Collection.Here customer
can see how many mugs have been
printer by each heater. This setting
can not be changed.. (fig.7.6).Once
finish setting,go back to the main
interface.
7.5
7.6

12
Exploded Views
GS-207M contains 4 main parts：
1. Machine base assemble
2. Control box assemble
3. Heating elements assemble
4. Pressure system assemble

13
1. Machine Base Assemble:
Parts list：
No.
P/N
Name
Qty
1
J.03.05.0600
Machine Base
1
2
J.03.06.0104
Round head bolt M3x6
2
3
J.03.04.0011
Switch Power Supply DC12V
1
4
J.03.04.0077
socket
1
5
J.03.06.0077
Countersunk screw M3x8
2
6
J.03.04.0079
On/off switch
1
7
J.02.04.0138
Circuit breaker 18A
1
J.02.04.0139
Circuit breaker 10A
1
8
J.03.04.0078
Terminal Block
1
9
J.03.06.0117
Ball headed bolt M4*10
2
10
J.03.03.0037
Rubber foot
4

14
2. Control Box Assemble
Parts List：
No.
P/N
Name
Qty
1
J.03.05.0602
Top Cover
1
2
J.02.04.0164
4 phase aviation plug(Male)
with wires welded
4
3
J.03.06.0165
Ball headed bolt M5-12
6
4
J.03.04.0166
Circuit board GSK-07
1
5
J.03.06.0117
Ball headed bolt M4*10
4
6
J.03.01.0025
Sticker
1
7
J.03.05.0403
Circuit board cover
1
8
J.03.06.0104
Round head bolt M3x6
4

15
3.Heating Element Assemble：

16
3.1.Heater Cover Assemble：
Parts List：
No.
P/N
Name
Qty
1
J.03.06.0102
Round head bolt M6x16
4
2
J.03.04.0184
Buzzer
4
3
J.03.05.0601
Heater cover
1
4
J.03.06.0032
Handle Screw
8
5
J.03.05.0456
Supporting pillar
2
6
J.03.05.0417
Heater fix board
4
7
J.03.05.0421
Bottom base
4
8
J.03.05.0414
Door type cover-1
4
9
J.03.05.0415
Door type cofer-2
4

17
3.2. Heater Shaft Assemble：
Parts List：
No.
P/N
Name
Qty
1
J.03.06.0117
Ball headed bolt M4*10
6
2
J.03.05.0426
Arc supporting plate
2
3
J.03.05.0419
Supporting board-1
1
4
J.03.05.0420
Supporting board-2
1
5
J.03.05.0418
connector-2
1
6
J.03.06.0103
Ball headed bolt M5*10
2
7
J.03.06.0142
Shoulder screw M5-6*12
1
8
J.03.05.0455
Connecting sheet
1

18
4.Pressure System Assemble：
Parts List
No.
P/N
Name
Qty
1
J.03.06.0005
Clamp
1
2
J.02.04.0148
Magnet switch
1
3
J.03.03.0003
Ball Shape Handle
1
4
J.03.06.0212
Screw M10-70
1
5
J.03.06.0127
Nut M10
1
6
J.03.05.0595
Connecting sheet
1
7
J.03.06.0140
Ball headed bolt M5*8
1
8
J.03.05.0596
Connecting set
1
9
J.03.06.0144
Cup head screw M10-20
1
10
J.03.05.0615
Connecting sheet
1

19
Electrical Schematic