Ganz PIXELPRO SERIES User manual

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 1

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 2
Precaution
Please read this manual carefully before installing the unit.
Never disassemble the camera. Unauthorized disassembly may cause equipment failure
or damage to the unit.
Please do not install the camera in a place exposed to direct sunlight.
Do not operate the camera in environments beyond the specified temperature.
Refer to “Environment Condition”on “APPENDIX (A) : SPECIFICATIONS”in this manual.
Before applying power to the camera, check the power source to ensure that it is within
the specifications. Refer to “Electrical Characteristics”on “APPENDIX (A) :
SPECIFICATIONS”

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 3
Table of Contents
Precaution................................................................................................................ 2
1. FEATURES............................................................................................................. 4
2. PACKAGE CONTENTS............................................................................................. 5
3. PART NAMES ........................................................................................................ 6
4. INSTALLATION ...................................................................................................... 7
4.1. Installing the camera.......................................................................................................... 7
4.2. Adjusting the angle of the camera..................................................................................... 8
4.3. Adjusting zoom and focus.................................................................................................. 8
4.4. Setting the Image Attribute ............................................................................................... 8
5. CONNECTIONS...................................................................................................... 9
6. CONFIGURATION ................................................................................................ 12
6.1.Set up network environment............................................................................................ 12
6.1.1. Generic IP Environment ............................................................................................ 12
6.1.2. Custom IP Environment............................................................................................. 13
6.2. View video on web page .................................................................................................. 14
6.2.1. ActiveX Installation.................................................................................................... 14
6.2.2. View video using IPAdmin Tool................................................................................. 15
6.3. Reset................................................................................................................................. 16
6.4. Factory Default ................................................................................................................ 16
6.5. Safe Mode ........................................................................................................................ 17
APPENDIX (A): SPECIFICATIONS .............................................................................. 19
Summary ................................................................................................................................. 19
Electrical Characteristics ......................................................................................................... 20
Environment Condition........................................................................................................... 20
Mechanical Condition ............................................................................................................. 20
APPENDIX (B): POWER OVER ETHERNET ................................................................. 21
PoE compatibility .................................................................................................................... 21
Power Comparison.................................................................................................................. 21
APPENDIX (C): DIMENSIONS ................................................................................... 22
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ................................. 23
REVISION HISTORY ................................................................................................. 24

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 4
1. FEATURES
Camera
1/3” 1080p CMOS Image Sensor
True Day/Night
DC Auto Iris Lens
WDR
20x Optical and 8x Digital zoom
Video
H.264 Baseline, Main, High profile (MPEG-4 Part 10/ AVC), MJPEG(Motion JPEG)
Max 30 fps in 1080p
Text Overlay
Analog Video Output
Audio
Two-way Audio Streaming
G.711 µLaw
Network
10/100 Base-T Ethernet
Integration
Software Development Kit (SDK) available
ONVIF Compliant (Profile S)
General
RS-485 (TBD)
microSD
Power Over Ethernet Plus(PoE+)
Video Contents Analytics (VCA)
VCA Presence (Standard)
VCA Surveillance (Optional)
VCA PTZ Auto Tracking

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 5
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
Camera
Video Output Cable
Quick installation guide
Terminal Blocks

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 6
3. PART NAMES
①3-Pin terminal block connector
For power connection (AC, FG, AC)
②Video Output Cable socket
Sockets for the video output cable included in
the package(CVBS : 1.0 Vp-p / 75ΩBNC)
③Audio microphone stereo jack connector
Connector for Audio input
④Audio speaker stereo jack connector
Connector for Audio output
⑤8-Pin terminal block (Digital Input)
Interface connector (IN4, IN3, GND, IN2, IN1)
⑥6-Pin terminal block (Digital Out)
Interface connector (2N.O, COM2, 2N.C, 1N.O,
COM1, 1N.C)
⑦LAN connector
RJ45 LAN connector for 10/100 Base-T Ethernet
(PoE+ supported)
⑧32-pin slot
Main socket for 32-pin connector on PCB.
⑨microSD slot
Supports up to 64GB.
Recommend Class 4 and higher for HD recordings
⑩Reset button
Use the button to restart the device or to reset it
to Factory Default. Refer to 6.3. Reboot and 6.4.
Factory Default for more details.
②
③
⑤
④
①
PCB View
⑦
⑥
Main Camera Top View
⑧
⑨
* Models and their appearance are subject to change without any prior notice.

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 7
4. INSTALLATION
4.1. Installing the camera
Caution
!
To prevent products from damage, place the camera on stable and non-vibrating
surfaces. If the stability is in doubt, consult safety personnel for reinforcements,
and then proceed with the installation.
1) Open the camera’s main top by
twisting it counter-clockwise.
2) Detach the roll-up string from the
main body to separate the main top
from the main body, and securely place
the main body on a stable surface.
3) Drop all the necessary cables from
the ceiling.
4) Push the lever inside the camera’s
main top inward to detach the center
part (PCB board) from the rest of the
main top.
5) Fix the main top to the ceiling by
inserting and tightening the three
screws into the holes.
6) Connect the cables to the connectors
and the terminal blocks on the PCB
board of the main top, and reattach the
center part by pushing back the lever to
the camera’s main top.
7) Pull up the roll up string from inside
of the camera’s main top, and insert it
to the roll-up string holder on the
camera’s main body while carefully
holding the main body.
8) Attach the main body and the main
top by aligning the triangle marks on
both parts.
9) Twist the main body counter-
clockwise once the two parts are
properly aligned.
32-pin socket
Roll-up
String
Holder
hole

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 8
4.2. Adjusting the angle of the camera
The device is 360° rotating camera and fully controlled by web user interface.
Refer to the provided “PixelPro GXi series Web Page User's Manual”for more details.
4.3. Adjusting zoom and focus
The device is equipped with 20x optical zoom lens with auto focus feature and fully controlled
by web user interface.
Refer to the provided “PixelPro GXi series Web Page User's Manual”for more details.
4.4. Setting the Image Attribute
Through the camera’s webpage, users can configure image settings.
The menu of image attribute is available under Video Appearance menu in Setup > Video &
Audio > Camera. The following features can be adjusted:
Brightness, Contrast, Saturation, Orientation
For more detailed information, refer to the provided “PixelPro GXi series Web Page User's
Manual”.

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 9
5. CONNECTIONS
①Audio connection
The camera provides a mono audio input and output. Due to low audio output power, an
amplified speaker is recommended for enhanced sound (Refrain from connecting a headphone
or an earphone directly to the camera).
②Sensor (DI) connection
Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor like the
following figures. The interface type can be controlled by web user interface.
Refer to the provided “PixelPro GXi series Web Page User's Manual”for more details.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Caution
!
Before connecting sensors, check driving voltage and output signal type of the
sensor. Since the connection is different according to sensor type, be careful to
connect the sensor. Do not exceed the maximum input voltage or relay rate.
Name
Descriptions
IN4
Alarm Signal Input 4
IN3
Alarm Signal Input 3
GND
Ground
IN2
Alarm Signal Input 2
IN1
Alarm Signal Input 1
GND
Ground
485+
Reserved
485-
Reserved
②
③
⑤
* Models and their appearance are subject to change without any prior notice.
④
①
Top View

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 10
③Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 30VDC/2A, 125VAC/0.5A, and 250VAC/0.25A
Name
Descriptions
NC1
Normal Close 1
COM1
Common 1
NO1
Normal Open 1
NC2
Normal Close 2
COM2
Common 2
NO2
Normal Open 2
Caution
!
Do not exceed the maximum relay rating.
④LAN connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45) to
connect the device to a hub or a router in the network. Refer to Appendix (B). Power over
Ethernet for more details.
⑤Power connection
The camera can be powered from either 24VAC or PoE+. If the camera is powered via PoE+,
refer to Appendix (B). Power over Ethernet for more details. To operate your camera using
24VAC, make sure the polarity is correct before connecting the power cable. Incorrect
connection may cause damages to the device.
Function
Pin
AC
input
AC~
1
FG
2
AC~
3
1 2 3

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 11
⑥microSD slot
Located on top of main device, next to 32-pin socket, a user must push the upper cover as
inscribed arrow direction next to “OPEN”to open the case.
Slide the microSD card into the opened cover with its gold contacts facing down.
Once the card is inserted, close down the upper cover, and push the cover as inscribed arrow
direction next to “LOCK”to lock the card down.
OPEN
LOCK
⑥

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 12
6. CONFIGURATION
6.1.Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the
device from converting the MAC address’s hexadecimal numbers, which is attached to the
device. Be sure that the device and PC are on a same network before running the installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.1.1. Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX are used,
users may view the live streaming images on a web page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal
Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of the device.
3. Web streaming and device configurations are supported through ActiveX program. When the
ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-1C-B8-01-23-45 →IP address = 192.168.35.69
Convert the last two sets of hexadecimal numbers to decimal numbers.

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 13
6.1.2. Custom IP Environment
IPAdminTool is a management tool, which automatically scans all of the network products for
users to perform administrative tasks, which includes network configurations, firmware update,
device reboot, and device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select “IP Address”; IP Setup window appears.
3. In the IP Setup’s window, information under ‘Local Network information’ displays the
user/PC’s network area information. Those information need to be incorporated to the IP
Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP Address, which
are to be the unique numbers for the device. Refer to the image above for the setting
4. Click ‘Setup’ to complete the modification.

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 14
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web browser.
The default username and password is root / pass.
6.2.1. ActiveX Installation
1. When the browser asks to install the AxUMF software, click Install to proceed.
2. When Setup installation pop-up window appears, click install to proceed with rest of
installations.
Note
i
Depends on system OS and Internet Explorer version, Installation experience
may differ from one another. Figures described above are from Windows 7,
Internet Explorer 9 environment.

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 15
Caution
!
6.2.2. View video using IPAdmin Tool
IPAdminTool automatically searches all activated network encoders and IP cameras and shows
the product name, IP address, MAC address and etc.
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse and select Web view
3. The system’s default web browser opens the device’s address.
Whether directly accessing the streaming video through typing IP address on a
web page or taking steps through IPAdminTool, the ActiveX is needed to be
installed for the Microsoft® Internet Explorer to have the complete
configuration privileges.

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 16
6.3. Reset
Perform the following procedures to reset your device:
1. Press the Reset button for 2 seconds while the device is in use.
2. Wait for the system to reboot.
Caution
!
Please do not hold the reset button for more than 2 seconds. Otherwise, the
camera may be switched to its Factory Default settings.
6.4. Factory Default
Resetting the device back to the factory default will initialize all parameters including the IP
address back to the factory defaults. To reset back to the factory default;
1. Press reset button and hold.
2. Release the button after 10 seconds.
3. Wait for the system to reboot.
Note
i
The factory default settings can be inferred as follows:
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway: 192.168.0.1
User ID: root
Password: pass
Reset Button Location

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 17
6.5. Safe Mode
What is Safe Mode?
Your IP camera or encoder could encounter an unexpected occasion such as broken firmware
file or uncompleted loading of firmware file during system booting. To restore the device from
the occasions, the device provides the emergency firmware as a factory default. Your device
will get restarted with safe mode when there is any error on your booting system files.
Why does your IP camera or encoder boot in Safe Mode?
Normally, the cause of ‘safe mode’ is classified into two types.
* When the power supply is unplugged in the middle of system booting.
* When the firmware files required for system booting are damaged.
IMPORTANT: Your device will turn into the safe mode when it fails to boot certain times.
How to recover your system from Safe Mode
The messages above will appear on the webpage when your device has been rebooted in ‘safe
mode’. Then, you should follow the instructions on the webpage according to the steps in a
row.
Note
i
There are two types of firmware files when you receive a firmware folder from
your vendor. When you need to update the firmware as the final resolution in case
your device is in safe mode like above, ensure that the firmware means the
firmware file for the device with the file name as GXi-V.1.X.X.X-~~~.enc.
Browse

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 18
Note
i
There is another method to update firmware, which is using IPAdminTool.
Please refer to ‘IPAdminTool User’s Manual.pdf’for the detailed procedure.
Note
i
If your device is still at safe mode after trying to update firmware, please contact
your local agency to get further assistance.
* Firmware update for safe mode itself: If you want to update the firmware for safe mode, you
should upload a firmware file with the following file name: GXi-SAFEMODE.~~~.enc.

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 19
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
CMOS
Image Sensor
1/3” 1080p CMOS
Scanning system
Progressive scanning
ELECTRICAL
Resolution
1920 x 1080
Min.
Illumination
Color: 1.5Lux(50 IRE) / 0.02Lux(Sens-up)
B/W : 0.1Lux(50 IRE) / 0.001Lux(Sens-up)
Auto IRIS(DC)
Supported
Lens
Focal Length
4.45 ~ 89mm (Optical x20)
Aperture Ratio
F1.6(Wide) / F2.9(Tele)
Angular Field of
View
H : 56.56°(Wide) ~ 3.10°(Tele)
V : 43.32°(Wide) ~ 2.34°(Tele)
Day & Night
Auto / Day / Night
Video
Compression Format
H.264, MJPEG Selectable per Stream
Number of Streams
Dual Stream, Configurable
Resolution
1920 x 1080, 1280 x 720, 1120 x 630, 960 x 540, 800 x 450,
640 x 360, 480 x 270, 320 x 180
Compression FPS
30fps@1080p
Motion Detection
Built-in
Burnt-in Text (Digital)
Video stream overlay text
Output
BNC, NTSC/PAL
Audio
Input/output
1/1 channel
Compression Format
G.711 uLaw
Function
Digital Input/output
1/1 channel
RS-485
Reserved (TBD)
Network
10/100 Base-T
Power over Ethernet
Supported
Protocol
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, RTSP,
RTCP, RTP/UDP, RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS,
DynDNS, NTP, SNMPv1/v2c/v3(MIB-II), IGMP, ICMP,
SSLv2/v3, TLSv1
SD Slot
1 microSD slot (up to 64GB)
※microSD Card is not included
(Recommend Class 4 and higher for HD recordings)

PixelPro GXi Series ZN-PTZ202XE Installation Guide
04-2014-A 20
Electrical Characteristics
Power Source
24VAC ±10%, PoE+ (IEEE802.3at)
Power Consumption
Max. 18W @ 24VAC
Video Output
1 Vp-p, 75Ω, Composite
Audio Input / Output
Mic in, Line out
D/I
Input voltage range:
0VDC minimum to 5VDC maximum, Max 50mA
D/O
Relay Rating:
Max 30VDC/2A, 125VAC/0.5A, and 250VAC/0.25A
Environment Condition
Operating Temperature
Operating Range (Indoor)
24VAC : 0˚C ~ 50˚C (32˚F ~ 122˚F)
PoE+ : 0˚C ~ 50˚C (32˚F ~ 122˚F)
Operating Humidity
Up to 85% RH
Mechanical Condition
Material
Plastic (ABS)
Color
Ivory
Dimension
180(Ø) x 240 (H) mm
Weight (Approx.)
2.1Kg (4.63 lb)
* The specifications above are subject to change without any prior notice.