FLIR Lorex LBV2711 Series User manual

Copyright © 2015 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE
LBV2711_SERIES_TRIFOLDQSG_EN_R1
MPX 1080P WEATHERPROOF
NIGHT VISION SECURITY CAMERA
Quick Start Guide
English Version 1.0
LBV2711 SERIES
153mm / 6.0”
70mm / 2.7”
Dimensions
70mm / 2.7”
Contents
• IR Night Vision Camera*
• Mounting Kit*
• 60ft BNC / Power Extension Cable*
• Power Adapter*
WARNING - A REGULATED power supply is REQUIRED for use with this
camera. Use of a non-regulated, non-conforming power supply can damage
this product and voids the warranty.
Warning/Caution
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the cameras within given temperature, humidity and voltage levels
noted in ‘Camera Specifications’.
• Do not disassemble the cameras.
• Do not point the cameras directly towards the sun or a source of intense
light.
• Use only the supplied regulated power supply. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use
harsh cleaners or aerosol cleaners.
Installation Tips
• Point the cameras where there is the least amount of obstructions (i.e. tree
branches).
• Install the cameras where they are difficult for vandals to reach.
• Secure cabling so that it is not exposed or easily cut.
• Cameras rated for outdoor use. Installation in a sheltered location
recommended.
* Per camera in multi-camera packs.
Camera Specifications
Image Sensor* 1/2.7” 2.1 MP
Video Format NTSC (LBV2711) / PAL (LBV2711P)
Effective Pixels H: 1930 V: 1088
Resolution 1080p @ 30FPS / 25FPS
Scan System Progressive
Sync System Internal
S / N Ratio 53dB (AGC Off)
Iris AES
AES Shutter Speed 1/60 (1/50) ~ 1/100,000 Sec.
Min. Illumination 0.2 Lux without IR LED
0 Lux with IR LED
Video Output MPX
Lens / Lens Type 3.6mm F2.1 / Fixed
FOV (Horizontal) 75°
Termination BNC Type
IR LED Qty. / Type 24 pieces / 850nm
Night Vision Range** 152ft (46m) / 102ft (31m)
Power Requirement 12V DC ±10%
Power Consumption Max. 290mA (w / IR)
Operating Temp. Range –22° ~ 140°F / –30° ~ 60°C
Operating Humidity Range < 95% RH
Indoor/Outdoor*** Both (IP66)
Weight (including stand) 0.8lbs / 0.36kg
* Compatible with Lorex MPX series DVRs only.
** Stated IR illumination range is based on ideal conditions in typical outdoor night time ambient
lighting and in total darkness. Actual range and image clarity depends on installation location,
viewing area and light reflection / absorption level of object.
*** Not intended for submersion in water. Installation in a sheltered location recommended.
Go to www.lorextechnology.com
Search the model number of your product
Click on your product in the search results
Click on the Downloads tab
1
2
3
4
Need Help?
Visit us online for up-to-date
software and complete instruction manuals
Resources

Setup Diagram
To Camera: To DVR:
Male Power
BNC
1. Connect the BNC and
power connectors to the
camera.
Female Power
2. Connect the BNC connector to
the video input of your DVR.
3. Connect camera to a power
adapter.
Connecting the Cameras
Before installing the camera:
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the wall
/ ceiling, you must run the cable
through the cable notch on the base.
This will keep the camera base flush
to the surface when mounted.
To install the camera:
1. Set the camera in the desired mounting position and
mark holes for screws through the camera base.
2. Drill the holes, then feed the cable through the
mounting surface or cable notch.
NOTE: Insert the included drywall anchors if
installing the camera in drywall.
3. Mount the camera stand to the surface using the
provided screws. Make sure all screws are fastened
tightly.
Installing the Camera Cable Extension Options
Extend the cable run for your camera depending on the cable type
used. Additional extension cables sold separately. See table below:
Option Cable Type Max Cable Run
Distance
1 Lorex model MCBL-60BNCU / MCBL-
60BNCU2 BNC Cable (included with
camera)
60ft / 18m
2 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’
Siamese (Video and Power)
300ft / 92m
3 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’
(Video Only)2
800ft / 242m
Notes:
1. The extension cable must be a single stretch of cable between the DVR
and camera. You cannot connect multiple extension cables to each other.
2. For cable runs above 300ft / 92m (option 3), you must connect the
power adapter directly to the camera, rather than at the end of the
extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently black & white (even during day time)
• Video is unclear, soft, or distorted
4. For more information on extension cables, visit
www.lorextechnology.com.
Problem Solution
No picture / signal •Ensure the camera is connected to an MPX
Series DVR. Camera is not compatible with
other DVR models. Visit www.lorextechnology.
com for compatibility information.
•Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.
•Ensure your DVR is properly connected to your
TV / Monitor.
•Ensure connections are properly connected.
•Ensure the camera power supply is plugged in.
Picture is too bright •Ensure your camera isn’t pointed directly at a
source of light (e.g. sun or spot light).
•Move your camera to a different location.
Picture is too dark •Check the brightness and contrast settings of
the DVR or monitor.
Night vision is not
working
•The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear •Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean
cloth.
•Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.
Bright spot in video
when viewing camera
at night
•Night vision reflects when pointing a camera
at a window. Move the camera to a different
location.
Troubleshooting
Cable Notch
ATTENTION - Test each camera prior to selecting a permanent mounting
location by temporarily connecting the camera(s) and cables to the DVR.
ATTENTION - This camera includes an Auto Mechanical IR Cut Filter. When
the camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and indicates
that the camera filter is working.
MPX DVR
LBV2711_SERIES_TRIFOLDQSG_EN_R1
Adjusting the Camera
A.
B.
C.
Adjustment Screw
1. Use a Philips head screwdriver (not included) to
loosen the adjustment screw.
2. Adjust the postion of the camera as needed:
A. Rotate the camera base 360°.
B. Twist the camera around the stand 360°.
C. Tilt the camera on the stand up to 90°.
3. Tighten the adjustment screw when finished.