Ganz ZC-PT series User manual

Installation Guide
1
Preface
The information provided in this manual was current when published. The company reserves the
right to revise and improve its products. All specifications are subject to change without notice.
Notice
To work with the PTZ cameras, any installer or technician must have the following
minimum qualifications:
•A basic knowledge of CCTV systems and components
•A basic knowledge of electrical wiring and low-voltage electrical connections
•Thorough familiarity with the contents of this manual
Important Information
Before proceeding, please read and observe all instructions and warnings in this
manual. Retain this manual with the original bill of sale for future reference and, if
necessary, warranty service. When unpacking your unit, check for missing or
damaged items. If any item is missing, or if damage is evident, DO NOT INSTALL OR
OPERATE THIS PRODUCT. Contact your dealer for assistance.
Copyright
Under copyright laws, the contents of this user manual may not be copied,
photocopied, translated, reproduced or replicated in any electronic medium or
machine-readable format, in whole or in part, without the prior written permission of
CBC Co. Ltd.
©Copyright2006CBC Co. Ltd.
Regulation
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.

Installation Guide
2
English
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the
product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact
your city office, waste disposal service or the shop where you purchased the
product.
Français/French
Élimination de votre ancien appareil
1. Ce symbole, représentant une poubelle sur roulettes barrée d'une croix, signifi e
que le produit est couvert par la directive européenne 2002/96/EC.
2. Tous les produits électriques et électroniques doivent être éliminés séparément
de la chaîne de collecte municipale des ordures, par l’
intermédiaire des installations de collecte prescrites et désignées par le
gouvernement ou les autorités locales.
3. Une élimination conforme aux instructions aidera à réduire les conséquences
negatives et risqueséventuelspour l'environnement et la
santé humaine.
4. Pour plus d'informations concernant l'élimination de votre ancien appareil, veuillez
contacter votre mairie, le service des ordures ménagères ou encore le magasin où
vous avez acheté ce produit.
Deutsch/German
Entsorgung von Altgeräten
1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt
angebracht ist, unterliegt dieses Produkt der europäischen Richtlinie 2002/96/EC.
2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom Hausmüll über die
dafür staatlich vorgesehenen Stellen entsorgt werden.
3. Mit der ordnungsgemäßen Entsorgung des alten Geräts vermeiden Sie
Umweltschäden und eine Gefährdung der persönlichen Gesundheit.

Installation Guide
3
4. Weitere Informationen zur Entsorgung des alten Geräts erhalten Sie bei der
Stadtverwaltung, beim Entsorgungsamt oder in dem Geschäft, wo Sie das Produkt
erworben haben.
Italiano/Italian
INFORMAZIONE AGLI UTENTI
Ai sensi dell’art. 13 del Decreto Legislativo 25 luglio 2005, n. 151 "Attuazione delle
direttive 2002/95/CE, 2002/96/CE e 2003/108/CE, relative alla riduzione dell'uso di
sostanze pericolose nelle apparecchiature elettriche ed elettroniche, nonché allo
smaltimento dei rifiuti"
Il simbolo del cassonetto barrato riportato sull’ apparecchiatura o sulla sua
confezione indica che il prodotto alla fi ne della propria vita utile deve essere raccolto
separatamente dagli altri rifiuti.
La raccolta differenziata della presente apparecchiatura giunta a fi ne vita è
organizzata e gestita dal produttore. L’utente che vorrà disfarsi della presente
apparecchiatura dovrà quindi contattare il produttore e seguire il sistema che questo
ha adottato per consentire la raccolta separata dell'apparecchiatura giunta a fi ne
vita.
L’adeguata raccolta differenziata per l’avvio successivo dell’apparecchiatura
dismessa al riciclaggio, al trattamento e allo smaltimento ambientalmente
compatibile contribuisce ad evitare possibili effetti negativi sull’ambiente e sulla
salute e favorisce il reimpiego e/o il riciclo dei materiali di cui è composta
l’apparecchiatura.
Lo smaltimento abusivo del prodotto da parte del detentore comporta l’applicazione
delle sanzioni amministrative previste dalla normativa vigente.
Polski/Polish
Utylizacja starych urządzeń
1. Kiedy do produktu dołączony jest niniejszy przekreślony symbol kołowego
pojemnika na śmieci, oznacza to, że produkt jest objęty europejskądyrektywą
2002/96/EC.
2. Wszystkie elektryczne i elektroniczne produkty powinny byćutylizowane
niezależnie od odpadów miejskich, z wykorzystaniem przeznaczonych do tego
miejsc składowania wskazanych przez rząd lub miejscowe władze.
3. Właściwy sposób utylizacji starego urządzenia pomoże zapobiec potencjalnie
negatywnemu wpływowi na zdrowie i środowisko.
4. Aby uzyskaćwięcej informacji o sposobach utylizacji starych urządzeń, należy
skontaktowaćsięz władzami lokalnymi, przedsiębiorstwem zajmującym się
utylizacjąodpadów lub sklepem, w którym produkt zostałkupiony.

Installation Guide
4
Português/Portuguese
Eliminação do seu antigo aparelho
1. Quando este símbolo de latão cruzado estiver afi xado a um produto, signifi ca
que o produto é abrangido pela Directiva Europeia 2002/96/EC.
2. Todos os produtos eléctricos e electrónicos devem ser eliminados
separadamente da coleta de lixo municipal através de pontos de recolha designados,
facilitados pelo governo ou autoridades locais.
3. A eliminação correcta do seu aparelho antigo ajuda a evitar potenciais
consequências negativas para o ambiente e para a saúde humana.
4. Para obter informaçõs mais detalhadas acerca da eliminação do seu aparelho
antigo, contacte as autoridades locais, um service de eliminação de resíduos ou a
loja onde comprou o produto.
Español/Spanish
Cómo deshacerse de aparatos
eléctricos y electrónicos viejos
1. Si en un producto aparece el símbolo de un contenedor de basura tachado, signifi
ca que éste se acoge a la Directiva 2002/96/EC.
2. Todos los aparatos eléctricos o electrónicos se deben desechar de forma distinta
del servicio municipal de recogida de basura, a través de puntos de recogida
designados por el gobierno o las autoridades locales.
3. La correcta recogida y tratamiento de los dispositivos inservibles contribuye a
evitar riesgos potenciales para el medio ambiente y la salud pública.
4. Para obtener más información sobre cómo deshacerse de sus aparatos eléctricos
y electrónicos viejos, póngase en contacto con su ayuntamiento, el servicio de
recogida de basuras o el establecimiento donde adquirió el producto.
Русско/Russian
Избавление вашего старого прибора
Этот символ на продукте или его упаковке означает, что данный продукт
нельзя подвергать утилизации вместе сбытовыми отходами всоответствии с
Директивой 2002/96/EC. Его нужно передать всоответствующий пункт сбора
для переработки электрического иэлектронного оборудования. Должная
переработка этого продукта позволит обеспечить отсутствие негативных
последствий для окружающей среды ичеловеческого здоровья, которые могут
возникнуть при выбрасывании продукта вмусорную корзину. Переработка
материалов позволяет сохранять природные ресурсы.
Для получения подробных сведений опереработке этого продукта обратитесь
вгородской офис компании, службу ликвидации бытовых отходов или магазин,
где был приобретен продукт.

Installation Guide
5
Cautions
•Handle the camera carefully
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be
damaged by improper handing or storage.
•Do not disassemble the camera
To prevent electric shock, do not remove screws or covers. There are no user
serviceable parts inside. Ask a qualified service person for servicing.
•Do not block cooling holes on the bracket
This camera has a cooling fan inside. Blocking the cooling holes leads to build up
of heat the camera and may cause malfunction.
•Do not operate the camera beyond the specified temperature, humidity or
power source ratings
Use the indoor camera under conditions where temperature is between 0~40°C
(32~104°F), outdoor camera between -50~50°C (-58~122°F), and humidity is
below 90%.
•Do not use strong or abrasive detergents when cleaning the camera body
Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove,
use a mild detergent and wipe gently.
•Never face the camera towards the sun
Do not aim the camera at bright objects. Whether the camera is in use or not,
never aim it at the sun or other extremely bright objects. Otherwise, the camera
may be smeared or damaged.

Installation Guide
6
Table of Contents
1. Introduction ............................................................................................................................. 8
2. Package Content................................................................................................................... 10
3. PTZ Camera Setups and Cable Connections ..................................................................... 12
3.1 Preparations for PTZ Camera Setups (Indoor Camera) ..................................12
3.2 Preparations for PTZ Camera Setups (Outdoor Camera)................................12
3.3 PTZ Camera Setups ........................................................................................15
3.3.1 Switch Definition ..................................................................................15
3.3.2 Communication Switch Setting ............................................................15
3.3.3 PTZ Camera ID Setting .......................................................................16
3.3.4 PTZ Camera Control Protocol .............................................................16
3.4 Cables and Connections..................................................................................18
3.4.1 Cable Requirements............................................................................18
3.4.2 22-Pin Data Cable ...............................................................................18
3.4.3 22-Pin Connector Definition.................................................................19
3.4.4 RS-485 Connector Definition ...............................................................20
3.5 Cable Wiring and Connection ..........................................................................21
4. PTZ Camera Installation ....................................................................................................... 22
4.1 PTZ Camera Dimension ..................................................................................22
4.2 Optional Accessories .......................................................................................23
4.3 Ceiling Mount...................................................................................................31
4.3.1 Hard-Ceiling Mounting / Indoor............................................................32
4.3.2 In-Ceiling Mounting / Indoor.................................................................34
4.3.3 In-Ceiling Mounting with Ceiling Panel ................................................37
4.3.4 Ceiling Mounting with Straight Tube (ZCA-ST25/ST50) ......................37
4.4 Wall Mount.......................................................................................................41
4.4.1 Mini Pendant Mount (ZCA-GT100) ......................................................41
4.4.2 Standard Pendent Mount.....................................................................45
4.4.3 Wall Box Mounting (ZCA-WBM) ..........................................................48
4.5 Corner Mount...................................................................................................51
4.5.1 Standard/Mini Corner Mounting Plate (ZCA-CST/MCP)......................51
4.5.2 Corner Thin/Wide Box Mounting (ZCA-CTB/CWB) .............................54
4.6 Pole Mount ......................................................................................................57
4.6.1 Pole Thin/Wide Direct Mounting (ZCA-PTDM/PWDM) ........................57
4.6.2 Pole Thin/Wide Box Mounting (ZCA-PTB/PWB)..................................60
5. System Expansion ................................................................................................................63
5.1 Connecting with Connector Box (Indoor Use)..................................................63
5.2 Connecting with Power Box.............................................................................64
5.3 Repeater Application .......................................................................................65
5.4 RS485 Distribution Unit (ZCA-DS4/8/16).........................................................66

Installation Guide
7
6. System Integration................................................................................................................ 67
6.1 Using Pelco Keyboard .....................................................................................67
6.2 Using Phillips Allegiant Keyboard ....................................................................69
Appendix A: Technical Specification.......................................................................................... 71

Installation Guide
8
1. Introduction
ZC-PT series integrated indoor PTZ Camera is a new subcompact designed to
deliver superb performance and durability with an intelligent and stylish housing that
is suitable in any security and surveillance installation. ZC-PT-XT series is a new
weather resistant integrated outdoor PTZ Camera. Both ZC-PT and ZC-PT-XT
series PTZ Cameras support one cabling for easy installation, and can be integrated
with CCTV products, such as DVRs, Control Keyboards, and CCTV accessories for
a total surveillance solution.
The PTZ Camera provides four models of new generation advanced DSP color
camera:
zZC-PT236 Model: 36× optical zoom / 12× digital magnification
zZC-PT235 Model: 35× optical zoom / 12× digital magnification
zZC-PT230 Model: 30× optical zoom / 12× digital magnification
zZC-PT226 model: 26× optical zoom / 12× digital magnification
zZC-PT218 model: 18× optical zoom / 12× digital magnification
General Operation Requirements:
A minimum of one control device is required for operation, such as a control
keyboard, a DVR or a PC. The integrated high speed dome camera contains a
built-in receiver that decodes commands originating from a control device.
The PTZ Camera supports one cabling for easy installation. Large set of built-in
protocols, including GANZ, Pelco, VCL, Philips, AD-422 (Manchester), etc, which
allow the PTZ Camera to be integrated with other suppliers' surveillance systems.

Installation Guide
9
Connect the PTZ Camera to other devices as shown in the diagram to complete a
video surveillance solution.
NOTE: To extend the network distance up to 1.2 km (4000 feet) and to
protect the connected devices, it is highly recommended to place a repeater
at the mid-point. However, a repeater may be needed in the network distance less
than 1.2 km if the used cables are not the CAT 5, 24-gauge cables (see 3.4.4
RS-485 Connector Definition). Refer to the repeater user manual for detailed
information.

Installation Guide
10
2. Package Content
Before proceeding, please check the box contains the items listed here. If any item is
missing, or if damage is evident, DO NOT install or operate the product and contact
your dealer for assistance.
Indoor PTZ Camera Standard Package
Camera Body
Hard Ceiling Mount
and Decoration Ring
Fixing Plate Optical Cover
Cable for Power,
Video, RS-485
and Alarm
Power Cord
Installation Guide
& Quick Guide
CD

Installation Guide
11
Outdoor PTZ Camera Standard Package
Camera Body with
Outdoor Mount Kit
Screws
Security screw
set
Water-proof rubber
Lubricant
Cable for Power,
Video, RS-485
and Alarm
Power Cord
Installation Guide
& Quick Guide
CD

Installation Guide
12
3. PTZ Camera Setups and Cable Connections
Before installing or connecting the PTZ Camera, please refer to this section and
complete preparations for camera setups and various switch setting.
3.1 Preparations for PTZ Camera Setups (Indoor Camera)
There will be a PE cloth sheet covered inside the camera cover and a lens cap on
the lens for shipping protection. Follow the steps below to remove those protective
materials.
Step 1: Unpack the PTZ Camera’s package and take out the camera body.
Step 2: Rotate the dome cover.
Step 3: Remove the PE cloth sheet and take off the lens cap.
Step 4: Replace the dome cover back.
3.2 Preparations for PTZ Camera Setups (Outdoor Camera)
This installation procedure is for the outdoor camera equipped with sunshield
housing. Please follow the steps below to complete camera housing installation.
STEP 1
Unpack the standard camera
package and take out the camera.
STEP 2
Rotate the Outdoor Mount Kit,
and take it off from the camera
body.

Installation Guide
13
STEP 3
Remove the protective cover and
PE cloth.
STEP 4
Attach the camera cover to the
camera body. Before doing that,
apply some lubricant on the
cover’s water-proof rubber to
make the installation process
smoother.
Note that the tiny protrusion on
the camera cover must align with
one of the four holes on the
camera body.
STEP 5
Gently pressure the camera cover
downward with two hands on the
side of it.
DO NOT press the cover as
shown in the figure; this might
cause damage to the camera
body.

Installation Guide
14
STEP 6
Screw the camera cover and
body together.
STEP 7
Set the switches located on the
bottom of the camera body. Refer
to section 3.3 PTZ Camera
Setups for detailed information
about various switch setting.

Installation Guide
15
3.3 PTZ Camera Setups
Before connecting the camera to other devices of CCTV system, please complete
the camera ID and communication switch setting. These switches are located on the
bottom of the camera.
3.3.1 Switch Definition
Please refer to the following figures and table for switch location and definitions.
Indoor PTZ Camera Outdoor PTZ Camera
A Camera Control Protocol Switch
B Communication Switch
C None
D 22-Pin Connector
E ID Switch
F Reserved
G ISP Connector (for FW upgrade)
3.3.2 Communication Switch Setting
The table below shows the function of each switch within the Communication Switch.
Communication Switch SW 1
SW 2 RS-485 Setting
SW 3 Termination
SW 4 Line Lock
SW 5 Factory Default Reset
SW 6 Reserved

Installation Guide
16
RS-485 is the interface that communicates the PTZ Camera and its control device;
for this reason, the RS-485 setup of the PTZ Camera and the control device must be
the same. The RS-485 default setting is half-duplex (see the diagram follows).
Please do not change the default setting without qualified specialist or supplier’s
notice. As for the SW 3 and SW 4, they are used for termination and Line Lock
adjustment respectively. The SW 5 is mainly used when users want to restore the
PTZ Camera to the factory default status; moreover, once firmware upgrade is
carried out, users also need to reset the SW 5 afterward.
RS-485 Setting
Half-duplex
Full-duplex
3.3.3 PTZ Camera ID Setting
Please change the camera ID if there is more than one camera on the same
installation site. To change your camera ID, please turn the arrow of the ID switch to
a desired number respectively. For instance, if the camera ID is 123, the ID switch
should be set as below. The default camera ID is “001”.
NOTE: No two cameras should be given the same ID, or communication
conflict may occur.
Hundreds Tens Units
NOTE: The number “0” should locate upwards as shown in above diagram
for correct switch definition.
3.3.4 PTZ Camera Control Protocol
Protocol is a specific set of rules, procedures used for data communications. Basing
on the devices of your surveillance system and define the protocol you are going to
use. Generally, use one protocol even the devices are provided from different
manufacturers. Use the switch to set your PTZ Camera control protocol and the

Installation Guide
17
baud rate. Refer to below table and turn the arrow to choose a protocol for your
camera.
Switch No. Protocol Baud Rate
00 VCL 9600
01 Pelco D 2400
02 Pelco P 4800
04 Chiper 9600
05 Philips 9600
07 GANZ-PT 9600
08 AD422 4800
09 DM P 9600
11 Pelco D 4800
12 Pelco D 9600
13 Pelco P 2400
14 Pelco P 9600
15 JVC 9600
16 GANZ-S 4800
17 GANZ-S 9600
18 GANZ-S 19200
19 GANZ-S 38400
21 Kalatel-485 9600
22 Kalatel-422 4800
Select protocol: Pelco D with Baud rate 2400, for instance, the protocol switch should
be set as below.
Tens Units
NOTE: The number “0” should locate upwards as shown in above diagram
for correct switch definition.

Installation Guide
18
3.4 Cables and Connections
The PTZ Camera is supplied with one integrated 22-pin Data Cable for connecting
with the power, video, and RS-485/audio input & audio output cables. Please read
the following sections thoroughly before making connections.
3.4.1 Cable Requirements
For operation, the PTZ Camera requires video, RS-485 and power cables as
described below:
•The video cable sends video signals to a remote viewing site. Using a coaxial
cable to send video signals is recommended.
•RS-485 cable carries commands from a control device to the dome cameras. A
CAT 5, 24 gauge cable is recommended.
•Power supply: AC 24V output voltage
NOTE: Ensure power supply meets the PTZ Camera’s power requirement,
or product impairment will occur. If any mistake happens, please contact with
a qualified maintenance engineer.
3.4.2 22-Pin Data Cable
A data cable (see the figure below) is shipped with the PTZ Camera for quick
installation for demo or testing usage.
NOTE: If the power lines use three wires, make sure the Ground wire is
inserted into the mid-pin of the terminal block as shown in the figure above.

Installation Guide
19
3.4.3 22-Pin Connector Definition
With the 22-pin connector, installers can simply connect the power, video and
RS-485 cables to the camera at once. For the definition of each pin, please refer to
the list below.
Pin Definition Cable Pin
Definition Cable
1AC 24-1 20AWG/18AWG
12 ALM-1
2ALM NC 13 ALM-3
3AC 24-2 20AWG/18AWG
14 ALM-2
4ALM NO 15 ALM-4
5FG 20AWG/18AWG
16 ALM-5
6 ALM COM 17 ALM-6
7 T+ 18 ALM-7
8 R- 19 ALM-8
9 T- 20 ALM GND
10 R+
24AWG
21 VGND
11 Alarm ISOG 22 Video 20AWG
NOTE: For alarm connection, please refer to section 3.5 Cable Wiring and
Connection.